How to disassemble the Kraton 8S down to the chassis
Пікірлер: 58
@PS3Nightassassin1249 ай бұрын
Was curious about opening my ESC Module to maybe upgrade my Receiver on my Kraton 8s and luckily this video was one of the first ones. I love the camera view and narrating, I love this new hobby I recently got into
@moereefer Жыл бұрын
i didn’t realize how old this was but i sure needed I never thought it was going to be this EASY 😮 I’m shocked been looking for a video like this for a few months. i bought the EXB version it was missing wheel wrench , it had no glue on one tire, left upper arm broken with like a crack and a lot of slop, all shocks leaking from bottom... i just received a care package basically even sway bars took. thank you 🙏 did i need this
@gaylanlee6447 Жыл бұрын
Just ordered this truck. I found your presentation very informative and enjoyed watching-even though 2 years after you produced it.
@bicketybamRC Жыл бұрын
Thank you!
@dis3nchant3d424 жыл бұрын
Nice dude! I just landed from a work trip and I'm literally driving right now at this moment to pick mine up. Super excited.
@RoadsideRC4 жыл бұрын
Nice video. These types of videos are really useful, and seem to just get repeated views over time. Well done!
@rchotboy1544 жыл бұрын
Loving the videos bro learning a lot 💯💪🤜🤛🤝🤙💯💯💯
@quazarraynor13624 жыл бұрын
Such a beautiful chassis.
@chrislrocks4 жыл бұрын
Excellent instructional video, to the best of my knowledge your the first owner doing so. Much appreciated, (saved). Very nice blend of bashing videos and with these instructional video. Makes your channel a one stop shop.
@lridebashitrc94224 жыл бұрын
Awesome instructional video.👍👍👍. Might be using it again. 👊🏻👊🏻
@porschetech24914 жыл бұрын
Wow. You wasted no time taking it apart. 👍 Chances of me getting one is more likely the more I watch vids like this
@marvinheadrick35114 жыл бұрын
The thick bead rolls in the chassis are exactly what these trucks (including the 6s versions) need. I’ve said it since the v4 came out. That being said, if there was a way to extend the bead rolls the entire length of the chassis, it would not bend near as easily (at least not front to rear). That may interfere with the attachment of the font and rear diffs, but I’m sure they could figure it out. Where do bends normally occur? Right at the front or back, where the chassis narrows at the front and rear bulkhead attatchment points. That’s where those bead rolls are needed most. This would lessen the need for pricey aftermarket chassis. Thanks for the tear down, informative👍🏻
@jessewoodworth3888 Жыл бұрын
But if the chassis were not to bend so easily there would be no need for the aftermarket high dollar chassis everyone's buying.Its all apart of there strategy 😉
@genreaper2 ай бұрын
Good to see you keep your fuilds up. 😂 Good vid. Tidy Rig too. Enjoy. PS: It is better to take to skid plates off before you slide the rear and front and that way to dont damage to O'rings that seal the lower diff housing. Up to you tho.
@thomaswalton90894 ай бұрын
Would it be ok to use a heat gun on the screws under the chassis cause they are way to tight and must have a good amount of thread lock
@maddogmiked12274 жыл бұрын
14:14 Wow, that was a near miss... Can't rebuild that as easy!!! LOL Great info.
@imserious21873 жыл бұрын
If you have to replace the servo saver, would you have to readjust the servo when you put on the new servo saver?
@Crewchief2274 жыл бұрын
Instead of waiting for a bigger servo mount, why not use a reducer and get a Savox 2290sg? Over 900oz of torque at 8.4v in a standard case
@Crewchief2274 жыл бұрын
Did I just see dual droop screws per arm? I was looking for them thinking "wow wonder how big those monsters are gonna be?", then saw dual M4s🤔
@bicketybamRC4 жыл бұрын
The highest the Max5 puts out is 7.4 and from what I can see that puts the 2290 at 694 oz. Not enough. Plus I know the optional electronics mount is due very soon 😎👍👊
@RCDUDE814 жыл бұрын
Nice breakdown and tips of disassembly Ed!👊Very helpful info to a lot!! I don't usually take time to do vids like this although I've been asked to a lot!😂I even hate doing unboxings..I leave that to the professionals! I just want to bash!!😅🤘👊👊🍻
@bicketybamRC4 жыл бұрын
I hear you, Eric. I don't do many but I figured since I was tearing it apart anyway I would try and help some people out. I remember when I first started with Arrma 18 months ago. I relied on "How to" videos all the time. Now I just wing it 😎👍👊
@nemocheerio4 жыл бұрын
Great video! Can you tell me how much the front should kick up when laid flat on the table? I'm going to check mine this weekend thanks to this guide.
@bicketybamRC4 жыл бұрын
I'll measure the angle in a bit.
@bicketybamRC4 жыл бұрын
Hi Ian. I used my angle finder and came up with a kick up of 8.3 degrees 😎 I hope that helps!
@nemocheerio4 жыл бұрын
@@bicketybamRC Awesome. THANKS!!
@nemocheerio4 жыл бұрын
@@bicketybamRC Thanks man. I was able to get my Kr8ton apart super easy and straighten everything out. Had a slight twist in the front due to a concrete pipe shooting up out of the ground when I wasn't looking. It's all good now. Keep up the great videos.
@imserious21873 жыл бұрын
The black connectors on the end of the motor fan wire and the ESC fan wire on mine was broken off during a crash, can those ends be replaced or can those wires be soldered back inside?
@bicketybamRC3 жыл бұрын
I would just buy a new fan. They are pretty cheap. But you can repair it if you have the tools and the skill.
@joshherrman32013 жыл бұрын
Have you had your shock bodies apart yet? I got some hotracing upper and lower caps and cannot for the life of me figure out how to remove the lower cap that the shaft goes through.
@bicketybamRC3 жыл бұрын
I have not.
@jasonbudd2950Jag4 жыл бұрын
Great Video buddy 👌 👌 First tear down I've seen on KZbin of K8S! Can you tell me please what you use to heat up Threadlocked Screws? I use a Soldering Iron which works most of the time & gets in nooks n crannies, but sometimes just not enough heat!! Do you use torch maybe? TIA
@bicketybamRC4 жыл бұрын
I use a mini torch or a heat gun. Both work well 😎👊👍
@jpdollasignakajpscorsese10264 жыл бұрын
Hey can u use rear shocks for front shocks I can’t find the fronts shocks no where complete i
@bicketybamRC4 жыл бұрын
Rear shocks are longer.
@jpdollasignakajpscorsese10264 жыл бұрын
bicketybam thanks alots
@williamalde81114 жыл бұрын
Have done a video of how to change the steering bellcrank kraton 8S?
@bicketybamRC4 жыл бұрын
I have not but it's not that hard. I think I show how to get it off in my bearing replacement video.
@williamalde81114 жыл бұрын
@@bicketybamRC first day out with hit a cement light pole. Broke front bumper and bellcrank so bummed. It ripped until that happened. Thank for your videos. Reason I bought one was for its durability.
@schmitty36074 жыл бұрын
What bits do you use for your impact
@bicketybamRC4 жыл бұрын
MIP
@kdhill114 жыл бұрын
Does HobbyWing make the stock esc?
@bicketybamRC4 жыл бұрын
It looks like a watered down Max6.
@hendrybudi84624 жыл бұрын
In this video did you change the rear cvd..?..if not what's going to happen cause i have a same issue..thanks
@bicketybamRC4 жыл бұрын
I can't remember if I did. What is the issue you are having? Is it bent?
@hendrybudi84624 жыл бұрын
@@bicketybamRC little bit it's look like your cvd..
@hendrybudi84624 жыл бұрын
Cause im worried if i run the rc is gonna ruin the diff..center or rear
@bicketybamRC4 жыл бұрын
@@hendrybudi8462 Well I just replaced mine this morning. I had a spare floating around so I did it.
@hendrybudi84624 жыл бұрын
@@bicketybamRC but my question is..is there something happened with your Diff center or rear when u run it or bashed it with bent cvd..?
@GreatLakesRC4 жыл бұрын
Yeah man getting to the center diff is a bit cumbersome 🤔 Nice teardown video 👍
@bicketybamRC4 жыл бұрын
It's a piece of cake compared to my Losi Super Rock Rey!😂
@GreatLakesRC4 жыл бұрын
@@bicketybamRC 😂😂 Yeah SRR like the SBR ain't easy to get to!
@Angel-dn9sm4 жыл бұрын
Your going to take it apart alot lol
@bicketybamRC4 жыл бұрын
Yes. I will be adding a lot of mods to this beast so I'm sure I will have it apart I'm the future 😎👍👊 One thing I wont be taking apart are the diffs. Man they are huge and so well made. I wonder if they could be retrofitted into an Xmaxx 😂
@nemocheerio4 жыл бұрын
I think if you're into RC and not taking things apart a lot, you're doing it wrong. :-) I'm personally glad to see this is such a breeze to disassemble into respective modules. Nice engineering.