Arrma vendetta Hot Racing spool slipper clutch eliminator for High Speed RUNs

[@avalanche0111]

What is the part number of the "little thing" you speak of?

[@rcusa201]

Wat time frame u hear me say

[@tonysmith7989]

Never saw you get an answer for the washers. They go on the screw after the thicker sloped spacer. 👍

[@Baronanto]

Your video had a glare, what exact parts did you use? Can I please get part numbers. Thank you

[@rcusa201]

Here watch this video I show parts and do it again kzbin.info/www/bejne/qIqYo4VseMRkjpI

[@janghyunc]

What is parts numbers? I just see only 0.8mod spur… Can you give me link?

[@rcusa201]

I don’t have link purchased it from hobby store

[@crystalellington7357]

Thank you Can you plz tell me what size GRP you used

[@rcusa201]

There’s only one size

[@crystalellington7357]

@@rcusa201 thank you

[@christiansrcs7789]

do you think this could be ran on a basher rc car? for example ima run this on a senton 4s with hot racing gears and 1/8 buggy wheels they are the same size as a slash/senton wheels

[@rcusa201]

Not a Good idea it will brake the plastic axles and drive shaft from bashing u need the slipper clutch for bashing wouldn’t be good idea

[@christiansrcs7789]

@@rcusa201 i have upgraded ones! the arrma ones

[@RangeKimTactical]

@@christiansrcs7789did you ever get rid of your slipper clutch for bashing and go spool?

[@SilentSassin]

Does anyone know what's the smallest size pinion that can physically fit on a setup like this (34T spool, arrma 3S motor mount)

[@rcusa201]

Not sure about that maybe 15

[@SilentSassin]

@@rcusa201 okay np thanks, just gonna buy an assortment of sizes and see

[@RittenhouseLifestyle7]

If your wanting to go for top speed your wanting to go up on the pinion.

[@WulfandCub]

Probably a dumb question but is the spool lighter than the clutch setup 🤔

[@rcusa201]

No spool heavier but more power not loss

[@JordanMaxwel-y6o]

Did you have to upgrade the diffs

[@rcusa201]

Nope stock did 116 my highest my friend did 150 stock diffs

[@TheTylerjoy04]

What Does The Spool Do? I Also Have A Vendetta.. But Thinking Of Making It Go Even FASTER..😊 I've Alredy Installed The Speed Pinion.. Got Use To The Speed, So Need To Go Even FASTER..Lol!

[@rcusa201]

Well the spool get Rids of the slipper clutch so no slip but trust me u can do good speed with slipper clutch but ur taking a chance they brake and then u loose control also I change gears to gonfaster I did 119

[@TheTylerjoy04]

@@rcusa201 Ooh I See..Thanks!! Will Changing The Motor Will Do, Like Installing A 4s 2500Kv Motor Increase My Speed & Faster Acceleration?

[@RittenhouseLifestyle7]

I had to learn the hard way with speed runs. I first built a TT02RR chassis. Then I put a 54T spur gear with a 32T pinion. Then kept moving up on the pinion one tooth at a time. I got to 98mph. Then I wrecked. Now the cars being rebuilt. I bought a brand new Vendetta and get it tomorrow. I intend to keep as is with just an upgraded center driveshaft aluminum, high speed center bearing and 2s and 3s batteries ready to go. Once I go for top speed, I will do the spool. Then come down in the spur gear teeth and up in the pinion teeth. This is how you build speed. Then once I max out the Esc and motor. Then you have to upgrade the motor and Esc amperage to get more power and run more battery cells. 4s-5s-6s-8s….16s ? You can even mount dual motors into an arrma chassis. They sell a mount for it. This requires other mods to the chassis but it can be done.

[@theconsciousone9017]

How fast does the car when you do this

[@rcusa201]

So far I did 116mph I’m sure I can push it to 130s

[@dover1966]

i install aftermarket fans if they are to powerful it will make the vendetta go into limp mode have u notice this stock esc and motor

[@rcusa201]

I don’t have stock esc

[@dover1966]

@@rcusa201 I thought u may know

[@rcusa201]

@@dover1966 yeah I keep that in mind for the castle system it’s true tho I work on real cars so when they r too cold they burn too much gas and don’t preform as they should

[@MrKillerhaze]

What gearing would you recommend for a 1900kv motors with 100amp esc ?

[@rcusa201]

For this car u gonna get 29 pinion unless u cut the case I would go down on the spool or try to get close 1-1 gearing ratio

[@riskaddictionrc]

What size pinion gear is that?

[@rcusa201]

27

[@SilentSassin]

@RC USA 201 nice video man, very detailed install. Do you know whats the smallest size pinion (16t, 18t, 20t) that would physically fit this 34T spur setup? I'm still on the stock 3900kv so need to gear way down till I upgrade.

[@doughoggatt1645]

Is this the same build for the Vortex?😀

[@rcusa201]

Same I have videos on vortex

[@ronjonesphotos]

I think I what to try this but I have a question for you... The little red insert you put on the front end of the eliminator, what is that called and where did you get it? Thanks!

[@newbierc650]

Arrma C9102 AR310881 Slipper Shaft Red 4x4 775 BLX 3S 4S

[@fbiagent3399]

I use blue/green and red loctite and all work in different departments.. If you want blue to work 100% at maximum strength you need to get A dremel with small wire brush wheel and hit the threads on the screws And Use something to clean them afterwards like rubbing alcohol on A napkin.. I've done this many many times and the screws always hold the way they should..

[@rcusa201]

Red!! All the way!! For me

[@yogamon]

Is that a 1515 1y?

[@rcusa201]

Yup

[@rcbustanut2057]

Nice vid bud😎👍 I believe this is the same setup for the Infraction 4x4 MEGA 1/8 scale. I was trying to see if there's a way to swap the gears with M1 gears. Hahaa, as I continued to watch the video it answered my question, it is the same for the Infraction. I just picked up one on their 50%off sale, $150.

[@rcusa201]

Yup it’s same

[@paulrakis]

Nice video man. Why aren't u using the slipper clutch it comes with ?

[@rcusa201]

I do speed runs not giving me good speed and it will brake and crash my car I did do good number with skipper clutch tho but I need to go faster

[@paulrakis]

@@rcusa201 ok wow yeah your like a speed racer. Yeah I'm using the same slipper clutch on my vorteks 3S but with the 55T spur been working great 👍

[@rcusa201]

@@paulrakis yeah it works good with stock systm once u change ur it will take bearing mines broke on one of the cars and lost control no brakes

[@modykujoperez261]

You couldn't even see the model numbers of the parts

[@rcusa201]

It’s on amazon all over and avable

[@Davespackey]

That’s wack af