ASUS B650E-F Strix Gaming Wifi [ Unboxing, specification, overview & additional Info ]

[@wakkowarner9522]

4:14 CORRECTION: The BOTTOM PCI-E expansion slot has a x16 connector but runs at x4, (for a maximum bandwidth of 8 GB/s using all 4 lanes). It does NOT run at x16. FURTHERMORE, when the third M.2 slot is used, the bottom PCI-E connector is DISABLED. Please read the manual before releasing a video with bad information!!

[@KleoYan]

Hi Wakko Warner. Welcome to my channel, point noted. Sorry for the misinfo. Apologies for that.

[@DiegoMartinez-vc5xy]

I have the same motherboard and going through the manual it says the bottom PCIe is 4.0 x16 (supports x4 mode) Does that mean it only supports x4 instead of x16 ?

[@KleoYan]

@@DiegoMartinez-vc5xy hi Diego Martinez, welcome to my channel and yes. That was my mistake. The bottom PCIe slot runs only at 4x.

[@JoeLiberto]

I was just about to say you can see in the video that the bottom PCIE slot doesn’t have pins throughout the 16x connector.

[@KleoYan]

@@JoeLiberto hi and welcome to my channel. yes that was my mistake. sorry about it.

[@bradcooper3306]

I have to really applaud you 👏🏼 👏🏼👏🏼 WOW. It is really incredible the level of detail you put into explaining and presenting products and components. I understand more from your videos than ANY other Computer/Build video I have a watched.

[@KleoYan]

Hi Brad Cooper, welcome back. Thank you for the compliment. hmm.. maybe this will interest you too. You don't have to get the theraml paste but the apply method is proven effective with the following advangates 1) dont have to worry if your thermal paste will cover or not cover the necessary areas (is it too much to too little) 2) evenly spread, 3) no wastage on thermal paste and 4) will not be in a mess when you want to do repaste. kzbin.info/www/bejne/rouVg2eopKtklbM

[@michaelmorales9697]

I'm so glad you mentioned the thing about the argb fans - i'm about to build my first PC with this board and don't want to overload or melt anything! Excellent, detailed review - Thank you :)

[@KleoYan]

Hi Michael Morales, welcome to my channel and all the very best with your build too. Thanks again for the feedback.

[@erdalguncel9038]

How to fix this problem ? Im first time builder and i wanna use 3 daisy chained fans(each 0.37A ) .fans and argb controlling looks the most confusing thing to me as a first timer

[@KleoYan]

@@erdalguncel9038 hi welcome to my channel. To resolve your issue. Find out more about an argb fan hub which you can use.

[@Djaym0]

@@KleoYan so if i bought of those Lian Li unifan with 3 daisychain fans kit with the controller i would be ok to use that with this board?

[@KleoYan]

@@Djaym0 yes they are as the fans are drawing power from the controller and not from your motherboard.

[@noxmu4715]

My god, two motherboards reviews in one day and both are in details. I am amazed by the time and efforts you've put in. Though you are not a English native speaker but the amount of work and efforts you have put in, you have my respect. Thank you Kleo. It seems like whatever PC component you've made the best out of them and to share what you know with us. You are truely awesome. Amazing work and keep it up buddy. 😘

[@KleoYan]

Lol, sorry Nox Mu,, too much to digest I guess, I was comparing three motherboards so decided to bring in two more motherboards experience to share with others. Just incase if you are not aware of those motherboards, they are the ASRock X670E Steel Legend, the ASUS B650E-F Strix and this motherboard. Thank you again for your support buddy.

[@kumaSOevl]

Kleo your English is really good. I understand you better than a lot of English native channels

[@KleoYan]

@@kumaSOevl hello and welcome to my channel, thank you for the compliment 😉

[@EkodeInk]

Thank you so much for the great video! You saved me from overloading a fan header, I was planning on putting three fans on one header but I completely forgot about the Amps! Liked and shared!

[@KleoYan]

Hi EkodeInk, welcome to my channel. I am glad you find this content useful. All the best with your build too.👍👍👍

[@Big_Gregg_B]

What a detailed fantastic video. I'll be using it as a reference most definitely! Thx!!!

[@KleoYan]

Hello Big_Gregg_B, welcome to my channel and thank you for your valuable feedback. I am gald this does aid you in certain ways. All the very best with your build 😉

[@EmperorJMX]

O M G The level of detail , the explanation, I learned a lot! sir you absolutely have my like, subscribe and a big thank you for the great in depth review.

[@KleoYan]

Hi Javier Miranda, welcome to my channel, call me Kleo will do. I am just like yourself a end user 😉 and thank you for the compliment. All the best with your build too.

[@topscene4u654]

hi man thanks for the video. i'm planning to get this motherboard. 7800x3D Will be fine in this?

[@KleoYan]

Hello Too Scene4u, welcome to my channel. It’s perfectly fine to run the x3D processor. Just make sure that you check the bios version and to update this board to support it.

[@PaulyDownUnder]

The ROG Asus website, it says the chipset is B650E, which you have in your title, but then during the video (@ 3:25) you mention it's only a B650. Can you please confirm?

[@KleoYan]

Hi Paul Down Under. Welcome to my channel. My bad it’s a B650E chipset.

[@Ohmnity]

Hey Kleo! I decided to jump the gun on this motherboard based on your review... and I'm now having second thoughts about it. Has it given you any troubles since your initial thoughts? I had a sour experience with this board given that the LAN drivers aren't recognized immediately when Windows is installed and because my USB3.0 header ripped and broke a pin after just one plug in, rendering 2 of my front USB-A ports useless. A USB port at the back also acts funny with an external DAC, if it's not turned on when booting it won't recognize it and it'll render the port useless until I reboot. Turning it on during normal use won't work, and if it's turned on when I boot my PC and then turn it off and try to turn it back on it won't work, it's just with that singular USB port though (top left from the blue USBs on the rear IO), the others work fine and this doesn't happen with anything else. The IO shield is also a tad loose on the top right corner for some reason. Curve Optimizer with -25 on all cores for a 7800x3D and 6000 MT/s G.Skill Trident Neo RAM with EXPO enabled work flawlessly though, I'd just like to know if it's a good board in the long run or if I'm better moving my system to an X670E Tomahawk instead. Running the latest drivers and BIOS too, pretty easy to set up to be quite honest. Keep up the great work! Also loved your LF III review and it's my cooler of choice with this CPU, really helped me make my purchase for both of these items. :)

[@KleoYan]

Hi Ohmnity, welcome to my channel. For me I didn’t run into any of your issue with this board but I do have to agree on the LAN part. I too have to do a local login in windows and to use a license key to activate windows. If given the choice of this and the MSI x670e tomahawk. I would take the tomahawk as it does have all the bells and whistles, plus during installation, the Lan/RJ45 is detected.

[@kevinbird8178]

Only plan on buying one AM5 motherboard so I need closer to the top with most of the advanced features, so I'm going with the X670E-E. I'm interested in the higher end VRM, AI Overclocking and asynchronous clock. I enjoy your channel. Thank you

[@KleoYan]

Hi Kevin Bird, welcome to my channel, though I do not have the ASUS Strix X670E-E board but after witnessing two budget boards can do, I beileve the X670-E has better VRM capabilities on overclocking. I am gald you have enjoyed my content and all the very best with your build too.

[@memeticist]

Thanks so much! I could not figure out what the other 4 pin connector was for on the CPU power connector, and now I know I don't need it. Messing with liquid nitrogen is a couple of levels beyond me.

[@KleoYan]

Hello Ken A, welcome to my channel and am glad you found something you needed.

[@synthruss3877]

Wait so now I'm confused, where have you heard that the chipset is B650, and not B650E? I've heard everywhere else and on every single source that it is B650E, and even on its product page it is AMD B650E certified.

[@KleoYan]

Hello Synthruss, my bad. Yup it’s b560e chipset alright. Thanks for pointing it out.

[@marceloxv7488]

Awesome video, very helpful. I'm gonna rewatch this video when I build my first pc. :)

[@KleoYan]

HEllo Marcelo xv, welcome to my channel and am glad you find this content useful. All the best with your build too. 😉

[@jawadturk]

Great explanation! You got my sub. I just bought this mother board today for my new Ryzen 9 build

[@KleoYan]

Hi جواد, welcome to my channel and thank you for your feedback. All the very best with your build too. 😉

[@heatheberly5838]

This is an AM5 motherboard. Not for Ryzen 9 AM4

[@NeeRock]

During your testing off the ASUS ROG Strix B650E-F did u find any Coil Whine i was going to buy that motherboard?

[@KleoYan]

Hi Nee Rock Jung Rana, welcome to my channel, nope I did not hear any coil whine while testing this board.

[@thedislikeguy9400]

goat reviewer

[@KleoYan]

Hi thedislike guy, welcome to my channel and thank you for your feedback.

[@Hellsfoul]

Very good video. Do you know, where the optical S/PDIF is at the rear panel? Of course Asus mentions, that there is one, but not which audio jack at the back is actually the correct one. Or is the manual wrong?

[@KleoYan]

Hi Hellsfoul, welcome to my channel. I am so sorry, I am not able to answer your question as I do not fiddle with optical S/PDIF. Terrible sorry.

[@SteveJohnson-f4b]

Hey thank you for the amazing in depth video,this is going to be my first time building a pc and I’m a little nervous and have a couple questions,I have ordered a Corsair 4000d airflow case and wish to install 5 case fans..is that possible with this motherboard? I was a little confused at 26:00 in the video where you explained a problem with the fan system,thanks if u decide to reply

[@KleoYan]

Hi Steve Johnson, welcome to my channel. I was trying to explain that each of these fan headers have a max capacity of 1ampere. And fans out there you are able to daisy chain them together which gives you only one connection point. you can do that but make sure to find our what's the total 3 fan ampere is before you plug. Example fan 1 to fan 3 are each rated at 0.30a. if you total them up, it will be at 0.90a which is not an issue to plug to any of these motherboard fan header (Each) If 3 fans daisy chained and total up above 1ampere, lets say each fan is at 0.4a, total will be 1.2a, then you should not be pluging to any of these motherboard fan header (Each)

[@daniel_wiersma]

@@KleoYan Hi KleoYan, thank you for your video. I recently bought this motherboard and I am planning on building my pc soon. Your comment abbout the Amps spooked me as I am really not experienced in computer parts and I didn't expect the amps to become a problem. After some digging around on the internet and researching the case I bought, it turns out a power repeater can be used for the fans. This way you can attach many fans to one fan header as the power is pulled directly from the PSU. Please correct me if I am wrong, but I think this would be the solution for this motherboard. I don't know if many cases come with a repeater, mine did in any case.

[@KleoYan]

@@daniel_wiersma Hi welcome to my channel. Yes you can use that and it's perfectly safe. Not all chassis comes with the Fan and argb hub which is powered by the PSU sata. That's the reason for some experience builders, they will purchase a fan and argb hub which draws power directly from the PSU instead from the motherboard and yes as you've mentioned, this will resolve the ampere issue. Thank you for your feedback and all the best with your build.

[@akkunzero]

Question about 9:34, do we have to use both 8-pin and 4-pin? or just 8-pin will do?

[@KleoYan]

@@akkunzero hi welcome to my channel. Only the 8pin EPS is required and it's more then sufficient to drive the processor, unless you are doing extreme overclocking.

[@crabbycat344]

thanks for this video !and the info ^^ and also the correction

[@KleoYan]

Hi crabbycat, welcome to my channel and thank you for your feedback, greatly appreciated it. All the best with your build too.

[@ten.kenobi]

Very detailed video. Helped me a lot. Thx & subscribed

[@KleoYan]

hi Ten Kenobi, welcome to my channel and thank yuo to have subcribed.

[@Takeshi1E]

hi, did u have any problems whit ram set at 6000mhz ? cuz i read a lot on reddit abut it, i wanna buy a 7800x3d whit this mbu and a 6000mhz corsair kit at cl30

[@KleoYan]

Hi Alex, welcome to my channel. nope I have not run into any issues. In this content am using a G.Skill Trident Z5 NEO Series (AMD Expo) 32GB Kit DDR5 6000 CL30-38-38-96 1.35V Dual Channel.

[@musm3367]

Good review. Regarding the fan header overheating issue, what fans do you recommend? I'm getting this board and wanted to hook up a 2 or 3 fan aio at the top, 3 fans on the right side of the case, and then 1 fan on the left

[@KleoYan]

Hi Mus M, welcome to my channel. For fan recommendation, I personally do not like ARGBs and will only go for budget fans like Arctic P12, P14, Montecl P120 METAL PWM or even Lian Li P28. It's all depending on the situation.

[@chewwy8858]

Is the rgb on the motherboard customizable?

[@KleoYan]

Hi Chewwy88, welcome to my channel. Yes it does, so long you have the Aura Sync installed with Asus Armoury Crate application.

[@Mrgoodnyt]

I was looking at using this board in the lancool 3 with an arctic 420mm AIO. Clearance for the rear I/O seems pretty tight judgeing by your previous videos. Do you think this combo would work? Thanks

[@KleoYan]

Hello oBrett McEwan-Jones, welcome to my channel. phew lucky you came here to ask. No you can't fit as the rear I/O of this board is 45mm tall. you only have 40mm clearance on the Lancool III if you mount the 420 AIO.

[@Mrgoodnyt]

@@KleoYan Big thanks for the reply, saved me a huge headache later. Its so hard to come across good info like that. youve defo earnt another sub love the videos cheers!

[@KleoYan]

@@Mrgoodnyt you are most welcome. I am glad to help. Infact do note that I am not a reviewer. This channel is base as a end user experience.

[@BigShotsEric]

THANK YOU for this review ..I just bought this mobo for a new pc build (my 2nd build ever) ..I have 2 questions I am hoping you or someone can help me with ..on this mobo I bought some gskill ripjaws s5 6000 cl30 "intell xmp" ram ..now on pcpartpicker it showed no conflicts but now I noticed the "intell xmp" on the ram ...will that intell xmp ram work with this mobo with a amd ryzen 7 7700x ? will I still be able to get the 6000mhz oc speed out of that ram? ....my 2nd question is on the m.2 slots should I be buying m.2 with or without heat shields? I can not find any info if i buy a m.2 gen 4 samsung 980pro with the heat shield if it will fit in this mobo or since this has those metal shields is having a heat shield on the m.2 itself even needed? ...I thank you so much in advance

[@KleoYan]

Hi, Iron Hidex, welcome to my channel. Yes I find it strange too when this board only mentioned about expo. Nevertheless if it does not support xmp. It will run at default 4800. Let me write in to check. And as for m.2 if it’s of 7000 speed. You can rely on the m.2 shield not an issue. Either way. You can get m.2 with it without the heatsink but as mentioned the m.2 armour shield on this motherboard is sufficient for gen 3 and gen 4 m.2

[@BigShotsEric]

@@KleoYan thank you so much for you quick reply... so the ram I bought i just made a mistake I didn't know about the xmp or expo or any of that like I said this is my 2nd build ever and now I'm kicking myself about it cause I really wanted that 6000 speed which guides say is the sweet spot ...my mobo arrives tomorrow and I'm gona try the ram and if it doesn't work at 6000mhz I'm gona half to try n return it and buy expo ram... on this mobo qvl it does not even show any 6000 cl30 ram on the list ...for a beginner ish builder like myself not knowing what parts will or won't work is super frustrating .... so what I meant with the m.2 is I bought a m.2 that has a heat shield on the m.2 itself ...will I be able to plug that in and still be able to put the metal covers that come with the mobo on top of the m.2 that has a heatshield build in? .... thank you so much again m8 ...I am having a heck of a time finding info on these issues I'm guessing because the parts are so new.... for around the 200-350 dollar mark do you think this mobo is one of the better options? I bought it just incase in the future 5.0 slots are used with new gpu or m.2 ...I only gona use this pc for gaming and will only use the auto OC features on the motherboard I don't know how to do any of that myself....... thank you so much again

[@KleoYan]

@@BigShotsEric Hi, you are most welcome, I do understand it can be fustrating at times to get PC components right, nevertheless thats our learning in progress :) dont be as you are not alone. ok as for the board to be honest it will last for awhile as compared to Intel current platform, at least what you've gotten now will pull through till Year 2025 if you need processor upgrades or even to get a PCI-E 5.0 GPU. so no issue there. As for your m.2 that comes with the heastink, in most cases, you can't include that while using the motherboard m.2 amour shield. You will need to remove the m.2 original heatsink and to use the motherboard m.2 shield instead.

[@BigShotsEric]

@@KleoYan Thanks again for the info ...I am going to be building my new PC tomorrow and will see how it goes ... this will be my 2nd build but using a bunch of parts for the first time ..water cooling, smaller case etc

[@KleoYan]

@@BigShotsEric ok if you need help and if unable to reach me here. You can always send me an email [e-mail] I will be glad to help you out if you need any. All the very best in your build.

[@ghettowoodfb6772]

hi Kleo Yan have you had any issued with the mother board and its bios since purchase? The reviews ia have read in the last 6 months have all been about problems with the bios. Can you make a follow up video on this motherboard perhaps? thank you great content

[@KleoYan]

Hi Ghetto Wood FB, welcome to my channel. I am so sorry I am not able to test this again as I have returned this motherboard. I do recall before updating to the latest bios. It works fine and even after the bios update. I have no issues.

[@juku619]

I have been looking to get this motherboard, is it possible to turn off the argb because i dont want lights inside my pc?

[@KleoYan]

Hi Juku, welcome to my channel. You can set Zero for brightness in Armoury Crate application. This will turn off the argb.

[@juku619]

@@KleoYan Thank you!

[@KleoYan]

@@juku619 you are most welcome.

[@matulu-p6x]

are you a part-time mechanic or arm wrestler? great detail though. thanks

[@KleoYan]

Hi matu lu, welcome to my channel. Thank you for your feedback. I am just a tech and diy person 😁

[@matulu-p6x]

@@KleoYan Glad I found you. btw will I be able to use 6600MHz ram on this board or it'll not support?

[@KleoYan]

@@matulu-p6x Hi and welcome to my channel. This board only support up to 6400Mhz max. I dont think it will run above specs.

[@matulu-p6x]

@@KleoYanhi. thank you bro 🙂. ohh since I've bought this dual channel vengeance and can't bother myself for refund, is there any alternative way to go around this and boot it up , maybe by reducing the clock speed to 6400Mhz? another thing is there huge difference between CL38 and CL36?

[@KleoYan]

@@matulu-p6x Hi, I will load the EXPO profile of your rams and if you ask me is there a big difference betwwen CL36 to CL38. I dont think you will feel the diff but in practice CL36 is faster as it's of a tighting cycle timing or cas lentency.

[@UchihaSabastian]

I have this same motherboard and there is one big problem. When I play game, I'm pretty sure I'm getting coil whine from the top VRM section. Before this, I had B550 F gaming Wifi and it also had same coil whine problem. I don't know what causes this but I think it's pretty common problem in Asus motherboard. There are several reddit post about this problem but there is no proper solution.

[@KleoYan]

Hi Uchiha Sabastian, welcome to my channel. As you've mentioned, it's not only on Asus motherboard but on some others which I've tested. Infact my ASRock Z790 Sonic PG does have this problem too. what I did was to RMA my board and am lucky enough that in Singapore, motherboards which are purchase locally, we can bring in our boards to local distro, test the replacement board and to accept the 1 to 1 exchange. You might want to RMA your board if it's too noisy.

[@Jacks_wr]

Hey brotha, thank you for this video! I am going to pick up this motherboard, i’m going to use lian li fans with the fan hub controller. You talked about the fans being a con. So my question is: in what slot would you suggest connecting the fan controller? I see the video is 4 months old so i hope you have time to reply. Thanks again

[@KleoYan]

Hi Jakos Wild Rift, welcome to my channel. if you are using the Uni Fan controller (SL,AL or SL infinity) you need not have to worry as the drawing power of those fans are from the uni fan controller and not from your motherboard. even if you did plug the PWM cable between the Uni Fan controller to your motherboard, it's ok. as mentioned the fan power drawn is from the uni fan controller, just make sure that the power source (Sata) is plug to the uni fan controller.

[@bryonbraces]

Able to compare this against the b650e-e and how this compares to the b650e-f

[@KleoYan]

Hello bryon, welcome to my channel. nope am not able to compare between them as I do not have the b650e-e. I see what I can do. thank you!

[@yooturboo]

from what i know on the b650e-e all m.2 slots are PCIe 5.0, it has 16 + 2 power stages & also 2 PCIe x 16 slots… the b650e-f has 1 PCIe 5.0 m.2 slot rest are 4.0, 12 + 2 power stages & 1 PCIe x 16, slot the rest are 4.0… not crazy differences if you really really want to “future proof” i’d go with the b650e-e

[@KleoYan]

@@yooturboo Hi and welcome back, thank you for the explaination. I should have read the manual and to answer his question. nevertheless, thank you.

[@yooturboo]

@@KleoYan no worries bro glad i can help

[@KleoYan]

@@yooturboo thanks buddy. greatly appreciate you help 😉

[@Metabus_]

very nice review, thanks for showing and explaning the bios. i was wondering which m.2 slot i should use because i heard some are better than others

[@KleoYan]

Hello Metabus, welcome to my channel, use the m.2 slot that is nearer to the CPU. That will be the fastest slot.

[@Metabus_]

@@KleoYan i see, thank you. So if i have two ssd's should i put my game drive in the top slot or the one that my operating system is stored on?

[@KleoYan]

@@Metabus_ hi for me I would install both OS and gaming program into one m.2 and to slot at the top slot nearer to the cpu. The rest of the m.2 like storage to the 2nd and 3rd slot. But if you have limited storage space on your m.2s then I will just have the os drive at the top slot and the game m.2 at the 2nd slot.

[@billnwa2250]

Thanks very much for a quality review on this motherboard.

[@KleoYan]

Hello BillnWa, welcome to my channel, am gald you like my content. Thank you to have visit my channel and you are most welcome. All the best with your build.😉

[@Anomaliateam]

There Is a way to use my gskill trident z5 6400 to his stock frequency without downcloak ? I have same mobo

[@KleoYan]

Hi Andrea Andolfo, if your g.skill runs at expo profile to 6400 which is unstable, pump the volatage by 0.5v. I hope thats what you are trying to ask.

[@Anomaliateam]

@@KleoYan thanks for the fast tips Bro , new follower . On mobo box It says 6400 compatibility , i Wish that 0.5 v could help me to run these RAM , if It Will not work how rightly downcloak to reach 6000 ?

[@KleoYan]

@@Anomaliateam mind if I ask what’s your ram timing?

[@fluzzles]

Do you think this Motherboard is a good option for a build with a Ryzen 7 7700X and 4070 Ti? Maybe also Overclocking

[@KleoYan]

Hello fluzzles, welcome to my channel. This I can’t answer you but undervolting is rock solid. I am sure this board is capable to overclock is at the middle of the E-A Prime and E-E-E Strix.

[@penguinclips9551]

Yes it a good board 👍

[@rodnietorres3082]

Can you do a review on the Asus rog strix b650E -E gaming Wi-Fi mobo? I’ve been trying to find videos on if it is worth buying but seems like their are none. This would be very helpful.

[@KleoYan]

Hi Rodnie Torres, welcome to my channel, I see what I can do, no promises though.

[@rodnietorres3082]

Another question, since motherboard has expo, if I buy a ram that has xmp, will it still work? Also what is the voltage/wattage of the fan header and rgb because I would like to use the Lian li uni infinity but I don’t know if the mother board can withstand those fans. I would greatly appreciate you help.

[@rodnietorres3082]

My bad, I didn’t realize you mentioned the amps but still will the Lian li infinity fans still work and if not, is their a way where you can make it work? Also the question with the xmp and expo.

[@KleoYan]

@@rodnietorres3082 if you are using the 3 fan pack set. It comes with a uni controller. Just supply sata power to it and connect the SL Inf fans and it will run fine. But if you purchase single pack fans then do not daisy chain more the 4 fan to an argb header to your motherboard.

[@kozmo5342]

Very informative you have my thanks !

[@KleoYan]

Hi Kozmo, welcome to my channel. I am glad you like the content. All the best with your build too. 😉

[@kozmo5342]

im building a pc for my brother and thanks to your info i found that this motherboard is perfect for his build, thanks i rarely give subs but your vid truly showed me that you deserve more. all the kind wishes bro. one more thing if you dont mind could i perhaps reach you on any platform privately for some pc building issue that i had?@@KleoYan

[@JetPackJuggernaut]

Thanks for this overview, I Just have one question I have two, m.2 nvme drives, one I plan to use for games, and the other for the OS. Which m.2 slot should the OS go in to? Considering the fasted slot closest to the cpu, I would assume would be better for gaming. Or does it not matter? thanks again for the video.

[@KleoYan]

Hi lsotrev, welcome to my channel. Assuming you have 2 x 2tb nvme and both are of PCIe 4.0 , install both OS and Games in one m.2 which is to slot the m.2 slot nearest to the processor on your motherboard and the other m.2 at the middle slot on your motherboard as game storage or data storage. That will be ideal. As both os and game load will be faster.

[@JetPackJuggernaut]

@@KleoYan Subscribed! the video helped a ton and thanks for the fast reply.

[@KleoYan]

@@JetPackJuggernaut you are most welcome and thank you to have subscribed. 😊

[@zane4006]

Hello, first I want to say that you have a fantastic and informative channel, now about this board, I read a lot of issues with his i225-v Ethernet chip by Intel, did you find any problem with that? (If you tested it) thanks for your job, you’re amazing!

[@KleoYan]

Hi Zane, welcome to my channel. I have no issues with internet connection with the i225-V, I mean what's your issue with it. I see what I can do to help you out and do pardon me for the late repy.

[@zane4006]

@@KleoYan I was about to buy this mb but I have read many issues with this i225-v Ethernet chip, such as drop connection to 100mega or even losing it for seconds/minutes depending on the case, but it is a well know hardware problem with these chip so I was wondering if the revision on this board suffer from that too! But anyway I bought the Tuf one watching your video, so thank you 🙏

[@KleoYan]

@@zane4006 hi and welcome back, I see, let me reach out to Asus to see if anything can be fix on this board. Do you mind to drop me an email [e-mail], if I find out anything, lets communicate through email on this subject as I might lost sight on where to reply. Thank you! btw congrats on your purchase on the Asus Tuf board. 😉

[@reiyoh_]

pairing this with the Lian Li Lancool 216 and was confused at why my fans the front weren’t lighting up. so i can plug the rgb into any of the 3 pin slots you mentioned or does it have to be a specific one?

[@KleoYan]

@@reiyoh_ hi and welcome to my channel. So long it’s argb 3pin 5v header of your motherboard. It will work. I will also advise you to install armoury crate and download the aura sync application. Then point to the argb header of your motherboard where you’ve plug your front fan argb connector to, then control the effects on aura sync.

[@matrix4342010]

Thanks a lot! This is so helpful, especially the part about the fan voltage. I bought this motherboard and I'm waiting for delivery. Do you recommend flashing the BIOS before assembling the PC, or should I assemble the PC and then update the BIOS through the UI?

[@KleoYan]

Hi The Myth The Legend, welcome to my channel. I will update the bios first before installing Windows OS. As the os will just register the new microcode binary.

[@myroslav6873]

Hey, nice vid. I have this board. How do I make use of that SPDIF header? What part do I need to buy to get the SPDIF out I connect to my speakers?

[@KleoYan]

Hi Myroslav, welcome to my channel. You will need a SPDIF amplifier or you can get speakers that has build in SPDIF.

[@gamingfromjohnwayne]

So my prebuilt came with asus prime b650m-a ax motherboard so I bought this one for 160😊.my prebuilt has 4 fans on my aio pump radiator. Will I have to unhook them from dazzle chain and run separately?

[@KleoYan]

Hi john wayne gaming, welcome to my channel. For prebuilt, I am not able to advise you as different SI (System Integrator ) have their own ways to plug fans to the motherboard header. I would advise you to check all the fans and argb connection points of your old motherboard and to determine which fans are to which headers. Then based on the old motherboard header layout. fit accordingly to your new motherboard. An example, liquid AIO radiator fans are plug to CPU_FAN on old motherboard fan header. then plug that to your new motherboard CPU_FAN header.

[@gamingfromjohnwayne]

@KleoYan thanks I will take it slow lol

[@KleoYan]

@@gamingfromjohnwayne ok, all the very best with your migration. Just a hint.. liquid AIO Pump, you should plug to the AIO_PUMP and as for Liquid AIO radiator fans, it should be CPU_FAN. the rest are case fans which you can use CHA_FAN 1 to CHA_FAN 4. The blue print of B650E-F on page 22 dlcdnets.asus.com/pub/ASUS/mb/Socket%20AM5/ROG_STRIX_B650E-F_GAMING_WIFI/E23880_ROG_STRIX_B650E-F_GAMING_WIFI_UM_V4_WEB.pdf?model=ROG%20STRIX%20B650E-F%20GAMING%20WIFI

[@gamingfromjohnwayne]

@KleoYan great thanks so much!

[@gamingfromjohnwayne]

@@KleoYan ur life saver lol

[@geecodeloco1138]

Awsome review I bought one my self but ran into a problem after installing it into my pc. I am stuck in bios. It recognises my m.2s, I have reseated my graphics card, I have removed the cmos battery and checked all my connections. Would you have any suggestions ? As I do not want to have to reinstall windows again and download everything all over again 😢

[@KleoYan]

HI GEECODELOCO, welcome to my channel. By right it should work when you plug your m.2 SSD to the first slot, but if you are bring forward from another motherboard to this motherboard, I would advise you to re-install windows.

[@geecodeloco1138]

@@KleoYan okay I’ll try reinstalling windows, will I still have all my previous programs and whatnot

[@KleoYan]

@@geecodeloco1138 if you do a fresh re-installation, you have to reinstall your other programs.

[@daviid27.]

There are some m.2 thermal pads that come in the box am I suppose to stick those in the m.2 ignoring the already existing thermal pad?

[@KleoYan]

Hello Ganymede, welcome to my channel. The thermal pad in the box is for spare. You can just use the existing pad that are on the m.2 shield.

[@daviid27.]

@@KleoYan Thank you Kleomede :) Unrelated question, perhaps you could help me. Im building my PC today. I have a AK620 cooler and used the included thermal past for the CPU (7600X) I also bought another thermal paste (Mars Gaming MT0), is it ok to use the deepcool thermal paste should I replace it for a better one?

[@KleoYan]

@@daviid27. you should be fine using either. Maybe test out both to see which gives you better result. Try this method to apply the thermal paste.kzbin.info/www/bejne/rouVg2eopKtklbM

[@Drvucb]

motherboard manufacturers are removing real POST CODE LEDs from low end boards, which is a shame, and replacing them with LEDs. the problem isnt positioning of the replacement indicator LEDs, its that there isnt a POST CODE 7 segment LED. The other problem with M.2s and connectivity in general, there is no longer a high end desktop segment, at least one that is affordable, that offers enough PCIe lanes to allow for things like M.2 slots, and full bandwidth PCIe slots, and more of them. Who wants to run their GPU that maybe they spent $1000 on, at X8? Also, ill bet the real market for people plugging in PCIe 5.0 M.2 into the second PCIe x16 (real x8) is very very small.

[@KleoYan]

Hi scbadq, welcome to my channel. I do share the same sentiment as in having to remove the debug LED digital screen on mid tier boards, for lowend I can understand. Now as for the PCI-E 5.0 slot with the Gen 5 m.2. I guess in every evolution stage, it will be there till a much mature board in future will be able to cater for full x 16 on both slots, the keypoint is time.

[@Direwoof]

why is teh plices so klazy for b650? Teh b550 of same baord was like 500 malaysian ringgit cheaper D:

[@KleoYan]

Hi Direwoof, welcome to my channel. I believe is for future set as you can upgrade processor and rams. Unlike b550 you can’t change to am5 processor or upgrade to DDR5 rams.

[@ten.kenobi]

I want to use 3 daisy-chained Lian Li Uni Fan Sl inf 120mm RGB on this board. Their Ampere rating isn't written on the Fan itself, nor can I find it in the manuals that come with it. Dr. Google didn't help either. Any chance u can tell me, whether or not it will work on the 1 Ampere rated headers on this board? Thx in advance!

[@KleoYan]

Ten Kenobi hi, for fan load (PWM) you dont have to worry, max fans you can use is 3 which each SL Inifinity fan load is at 0.18a = total 0.54a but for argb load is 0.60a thats where you need to think how many fans will you be using and to check the argb load of this motherboard. (refer to manual)

[@ten.kenobi]

@@KleoYan thank u very much. I will study the motherboard manual for max argb header load.

[@KleoYan]

@@ten.kenobi you are most welcome. all the best with your build.

[@lucasniemeyer3381]

As i have just bought the Mainboard im asking myself how to connect the Case Fan 4. The location of the header is very inconvenient.

[@KleoYan]

Hi Lucas Niemeyer, welcome to my channel and I am so sorry for the delay response as I didn't get any notification. Thanks for your feedback and yes if you have fans at the bottom, it will be hard to unplug and to plug it back in at the bottom.

[@Ro7770]

Should i get this or the Gigabyte X670 Aorus Elite AX would you say? The gigabyte one has better vrm design (16+2+2) but am i missing something ?

[@KleoYan]

Hi Socrates, welcome to my channel. do pardon me as I've no experience on the Gigabyte X670 Aorus Elite AX, but they are well known for good VRM heatsink. you can give it a try.

[@thehahahaha88]

hi , good review. do you think this mobo can handle 7950x no problem ? thanks

[@KleoYan]

Hello Gon Is Gone. Welcome to my channel. Yes it can handle. No issue.

[@dirkhenkel9410]

Hi, nice video and very detailed, thanks for that. I´m planing to buy one of those, so thank you for the video. One thing I think is not right is with your take on these fanheaders. There is no way they could melt, the headers themselves would be able to handle more than 5 amps. But the fan controller is of course limited. So your critics may be basically right, when you think of connecting many fans and a pump. Exept you have a short of course, but than the traces would fail first. You should watch your powerdraw, that can be an issue! Another thing I´m wondering, you said this is not a E- chipset? That would be a fraud by ASUS since they call it a "B650E-F Strix Gaming Wifi" ...

[@KleoYan]

@@dirkhenkel9410 Hi and welcome to my channel. I wouldn’t say am an expert on the fan ampere but I do have encounter or had bad experience with connector melt. It does melt when one fan is at 0.5A which 3 total up of 1.5A. As headers you have mentioned, capable up to 5amp, but not to each header. For me to use an asus board, I normally use a fan hub with a sata power source, which current is drawing directly from the PSU. Next to plug the hub PWM cable to the motherboard fan header. I feel safer this way without damaging the fan headers. Yes I do take precautions when plugging daisy chained fans to any motherboard header. As for the chipset, it’s my bad, it is a b650e and not a B650. Thanks for your feedback and the best with your build. 👍👍👍

[@S.D1010]

Would ot be able to handle 9900x ?

[@KleoYan]

@@S.D1010 hi and welcome to my channel. Do pardon me as this board was returned to ASUS SG. But I believe it does. You will need to update your bios. Kindly refer to this list rog.asus.com/motherboards/rog-strix/rog-strix-b650e-f-gaming-wifi-model/helpdesk_qvl_cpu/

[@gandharkambare2335]

Is this motherboard good for future amd am5 processors? Just asking because it has 12+2 vrm.

[@KleoYan]

Hi Gandhar Kambare, welcome to my channel. Now I am not able to commit to tell you that this board is future proofing but based on AMD promise, the AM5 socket will stay till year 2025. So if it's based on what AMD have mentioned, yes, this board is able to carry to the next few generation, do note that a bios update might be necessary for newer generation AM5 processor.

[@gandharkambare2335]

​@@KleoYanthanks mate

[@KleoYan]

@@gandharkambare2335 you are most welcome. All the best with your build. 😉

[@shadybang3362]

Great job this video just made my decision easier to decide

[@KleoYan]

Hi Shadybang, welcome to my channel. Am glad you did find this content useful, all the very best with your build too.😉

[@182BlinkStar]

Would this motherboard pair nicely with the R7 7700x?

[@KleoYan]

Hi 182BlinkStar, welcome to my channel. yes this board will pair up nicely with 7700x without issue. Infact if you are into gaming, you can choose to use the Tuf too if 2 m.2 is sufficient for you. kzbin.info/www/bejne/r5TXeaWPm7anj6s you see, the Tuf board is as good too and it's much cheaper, so that you can use that to get a better graphic card. This is just my opinion.

[@182BlinkStar]

I ended up purchasing the R7 7700x and the b650E-F. Also just ordered a 3090 graphics card. Can you recommend ram and power supply?

[@KleoYan]

@@182BlinkStar oh congrats on the newly purchase. as for rams, I have good experience with G.SKill Z5 Neo and the Ripjaw XS series. I have yet to test another others. As for PSU, majority will go for Corsair RM or HX series, personally I like Seasonic Prime series.

[@ahmedghanimal8278]

is it enough power for 7950x3d full load ?

[@KleoYan]

Hi ahmed ghanimal, welcome to my channel. by default yes, this board is sufficient to drive your 7950X3D

[@ahmedghanimal8278]

@@KleoYan this MB or rog x670E-A ?

[@KleoYan]

@@ahmedghanimal8278 I would go for ASRock X670E Steel Legend. kzbin.info/www/bejne/l526oqCHftZnq9k

[@yooturboo]

been waiting for someone to make this video thank you

[@KleoYan]

Hi Aue Dj, welcome to my channel. You arr most welcome and thank you for your valuable feedback. All the very best to your build too 😉

[@adrienmeesemaecker2054]

Great videos, you really deserved more !! Do you know if I can plug 3 Lian Li TL LCD non reverse 120mm in daisy chain on one plug like you talked in end of video ? Can’t find informations :(

[@KleoYan]

Hi Adrien Meesemaecker, welcome to my channel. For the TL LCD fans, you will need to plug to it's controller. it's not advisable to plug directly to the motherboard fan headers Once you have plug the TL LCD to its controller, from the controller there is a PWM connector where you can then plug to any fan headers of your motherboard.

[@adrienmeesemaecker2054]

@@KleoYan thank you for your answer. Keep the great work !

[@KleoYan]

@@adrienmeesemaecker2054 you are most welcome. All the best with your build too.

[@adrienmeesemaecker2054]

@@KleoYan O11 vision with watercooling on rear fans and 3 tl lcd in front then 3 p14 max bottom if can put a vertical mounting GPU on b650e-f rog strix :)

[@KleoYan]

​@@adrienmeesemaecker2054 I am unable to answer your question as this content is about this B650E-F strix motherboard. I have no idea whicih PC case will you be using to apply the GPU vertical mount bracket.

[@TheDiabeticWay]

Thank you for this video extremely helpful!

[@KleoYan]

Hi The Diabetic Way, welcome to my channel, am glad you find something useful, all the best with your build too. 😉

[@TheDiabeticWay]

@@KleoYan Thank you lots seem to have changed since my last Asus Motherboard and will be trying to follow your video as much as possibe thank you for your time in doing this really helps! Did you have any hiccups on th efirst boot with it at all? I think thats the worst bit switching it on for the first time hoping it does not melt your process 🙂

[@KleoYan]

@@TheDiabeticWay Hi and nope, I dont have any issues on first boot. Infact what I normally do is to plug only the essential componets on a test bench which include these. 1) Processor 2) Rams 3) Plus only the 24pin and 8pin EPS cable to the motherboard. boot it up to UEFI. It will take sometime to boot as newer generation system which make use of DDR5, you will need to let it run (Memory Training Cycle). You might feel that it's not running but it is.. just need a couple of minutes and to wait for it to boot.

[@TheDiabeticWay]

@@KleoYan thanks for the reminders! I nwas being braver and adding the HD audio and usb2.0 but nice to know you booted up first time, Im always ready to turn off fast in case fans don't start hehehe :-) and cross fingers as first boot I thinks the worst at knowing if you have any issues. I also seen a good video on ASUS Motherboard Troubleshooting via Q-LED in case needed. Nice to know though its going to take a while thank you!

[@TheDiabeticWay]

@@KleoYan It also just says power connectors on my motherboard not as detailed as Id like really in the manuals! Has you called it EPS mines different I also got advice I do not need them all in for some strange reasons but if that's Tecnical I tend to stick to what they advice 🙂

[@matrix4342010]

I'll be using 7 Thermalright TL-M12 fan , The Asus ROG STRIX B650E-F GAMING WIFI motherboard supports up to 3A on its 5V ARGB headers. Each Thermalright TL-M12 fan draws 0.15A for ARGB lighting, totaling 1.05A for seven fans. This is well within the 3A limit per header. do you think connecting 7 ARGB fans to a single 5V ARGB header is safe and should not exceed the power limit of the header. ?

[@KleoYan]

Hi Human, welcome back. The readings of each fan’s LED are at 0.15a and you will not have a problem to daisy changed 10 fans to one ARGB header which is 3A. It is safe to so no worries. 😉

[@jackdawson4807]

I just bought this motherboard but the second m.2 drive does not show up no matter what i try. Any ideas would be helpfull.

[@KleoYan]

Hi Jack Dawson, welcome to my channel, kind of I ask which m.2 are you using. The brand and model?

[@jackdawson4807]

@@KleoYan its a samung m.2 . One is wd which i am using . But the second one is installed but is not showing up on bios or windows. I think it has something to do with the pcie slots but not sure what it is. Can u help out

[@KleoYan]

@@jackdawson4807 hmm 🤔 1st remove the Samsung m.2 from the slot, place the WD m.2 to the slot, see if it detects? If it does, the motherboard slot is not faulty. 2nd if this slot is not faulty, use an eraser, rub and clean the Samsung m.2 contact point. Then try again. If it still does not work then most likely is the m.2 issue and not the slot.

[@skidrow-black]

Awesome review bro

[@KleoYan]

Hi Skidrow Black, welcome to my channel and thank you for the feedback. But do read the pin comment from AX as I did a mistake about the PCI-E lane. Thank you again to have visited.

[@Raindeer0448]

Would 64gb of ram work well with this motherboard? Smbdy let me know

[@KleoYan]

Hi Fryem, welcome to my channel with 2 sticks as in 2 x 32G Kit is not an issue but if you are thinking of doing 4 sticks as 4 x 16G, there might be some issues. you might need to do some ram tweaks to make it run. often 4 stick rams can't go with tighter timing and higher bus speed.

[@Raindeer0448]

@@KleoYan thank you so much for your reply I had to make sure I didn’t have to buy a b670 motherboard in order to run 64gb of ram

[@KleoYan]

@@Raindeer0448 you are most welcome and which rams are you getting and do you might to share the timing and bus speed?

[@Raindeer0448]

@@KleoYan I’m getting 2x32gb 6400mz of RAM with your same motherboard with a Ryzen 7 7800x3d unless you think me getting a b670hero would be better?

[@KleoYan]

@@Raindeer0448 In general, any mid tier Asus board is capable to run 2 sticks 64G Kit. Personally I will stick to this board if you are just getting a 7800X3D, spend more on your GPU hee hee.

[@Alex45684]

16:22 does this mobo support windows 11 /has it TMP ?

[@KleoYan]

Hi __press_me_every_day_, welcome to my channel, yes it does support TPM for windows 11.

[@the_red_knight1581]

Hey, love the reviews! I have a question for you would this motherboard fit in a lian li lancool III together with a Arctic Liquid freezer II 420mm? Thank you for the many great reviews keep up the good work!

[@KleoYan]

Hello The_Red_Knight, welcome to my channel. I am sorry to tell you. Nope it does not fit with a 420mm AIO. Unless you use a 360mm. Thank you for visiting and all the best with your build.

[@the_red_knight1581]

@@KleoYan Do you have an idea which am5 motherboard would fit with a 420mm? If not I guess I have to give up the idea of using a 420mm rad unfortunately.😁

[@KleoYan]

@@the_red_knight1581 am sorry to say. Nope I do not know if any as those I have reviewed are all unable to fit. Unless you want to fit a 420mm AIO at the front but you have to use the corsair 420 AIO though.

[@koraykorac5463]

Hello,can you tell what about boot time and Ethernet i225 problem. I m planing to buy this board with 4800Mhz, 16GB (2x8), going to use stock setting.If ı use higher Mhz and use expo, i read all over the inter boot time will be slower.Also most user have Ethernet i225 problem about internet.Have you encounter these problem?

[@KleoYan]

Hi koray koraç, welcome to my channel, yes I do face this issue. As what I did is this 1) download the current driver of this board. rog.asus.com/motherboards/rog-strix/rog-strix-b650e-f-gaming-wifi-model/helpdesk_download/ (Intel I225/I226 LAN Driver V2.1.3.3 For Windows 11 64-bit.) 2) uninstall the driver that's on your windows 3) reboot your PC 4) install the new driver you have install, check and see if you have the issue. 5) If you are having issues, go to the network adaptor and to disable these - Advanced EEE - Energy-Efficient Ethernet - Power Saving Mode - Green Ethernet

[@koraykorac5463]

@@KleoYan I read that the problem is with the hardware related and they release the i225 v3 of the motherboard. But I don't know which version of the motherboard I will buy from the market. Most vendors still sell the first version.

[@KleoYan]

@@koraykorac5463 I see, in most builds I have done for friends. I just update the driver from the motherboard website and then turn off the EEE settings in network adaptor and the Power Green settings. That fix the issue in most of my cases. It's not only AMD platform. Intel Z690s and Z790s too, also with the E3100 2.5Gbe too. All these boards that are having the issue, I performed what I've shared with you and issues are gone.

[@NightWwolf]

I have this motherboard and it’s not detecting the tpm 2.0 so I can upgrade to windows 11 do I have to buy the tpm2.0 add on and plug it into motherboard or is it already built in

[@KleoYan]

@@NightWwolf hi welcome to my channel. It’s with the board. TPM mode chip is only needed if you want full encryption which are meant for enterprise level. You do not need the chip to start with. This board already have the socket or pin. Just enable it and you will be able to install windows.

[@NightWwolf]

@@KleoYan I have it enabled in bios but windows still isn’t detecting tpm2.0

[@KleoYan]

@@NightWwolf hmm. Remove the tpm chip and do a clear cmos, see if that helps.

[@NightWwolf]

@@KleoYan where is the tpm chip located

[@KleoYan]

@@NightWwolf oh sorry I read incorrectly. I thought you purchased the tpm chip. If ignore my last response. Did you clear cmos and try again. By default after clear cmos. Go to bios or UEFI. Go to advance and check under AMD fTPM configuration, make sure it’s enabled.

[@boboboy8189]

I just want to sleep and I saw this video....I planning to buy x670E Steel legend or this board. I still undecided to choose which one

[@KleoYan]

Hello Bobo Boy, welcome to my channel. Indeed both are good boards. I would be stuck like you too and myself have the steel legend. I grow to like it but when this board is out. I have second thoughts but I end up happier with the steel legend as it has another m.2 slot. One again thank you to have visit and to leave your valuable feedback. 👍

[@shaza1910]

Hello! I bought a Samsung 980 Pro 2TB M.2 .Which slot should I put it in?The top one? Thank you!

[@KleoYan]

Hello Shaza, welcome to my channel. it greatly depends what you are using your m.2 for? if it's for storage, any of the bottom m.2 slot will do. if you are using it as an OS or Grame app drive, then plug it to the 1st m.2 slot nearest to your Processor.

[@shaza1910]

@@KleoYan Thanks for the quick response.Everything will be on it. Windows, games.

[@KleoYan]

@@shaza1910 I see, then plug to the first slot near the processor, you will get to enjoy the fast response.

[@shaza1910]

@@KleoYan Thank you!

[@KleoYan]

@@shaza1910 most welcome and all the best with your build.

[@vkmalik610]

i have subbed the channel and loved your review I Just ordered Ryzen 7600x Asus Rog strix B650E-F G.Skill 32 GB 6000Mhz Now when you pointed out the ARGB header issue I am kinda nervous… I have Lian Li dynamic o11 and 6 ST120 and lian li 360mm Galahad AIO and 1 More Fan My recent MSI B450 gaming pro Carbon AC showed VGA error everything was working tried another GPU PSU RAM CPU cleared and reset the CMOS, Bios flashback too but VGA light was on and no Motherboard logo came on screen. Luckily I saved enough money for the upgrade.

[@KleoYan]

Hi VK Malik, welcome to my channel and thank you for the compliment. As for the argb and rgb header which are blocking the post code, that will be minimal if the cables are zip tied away from the post code led. It should be alright. Btw all the very best with your build and as for your Pro Carbon AC, if it’s still under warranty, you might when to have it repaired.

[@tarnishedtony9925]

thank you so much I was looking at my psu like I dont see another 12 pin connector lol so I just need the 8 pin cpu not the extra 4 lol. thank you so much u helped me a lot. I subbed to your channel❤❤❤❤

[@KleoYan]

Hi Tarnished Tony, welcome to my channel and thank you to have subscribe to my channel. All the best with your build too.

[@personwhosayshelloparrot3983]

can work with a ssd at 7000mbps??

[@KleoYan]

Hi Person who Says Hello parrot 396, welcome to my channel. If you are referring to nvme n.2. Yes it does work. No issue.

[@penguinclips9551]

Love this board 👍

[@KleoYan]

Hi penguin clips, welcome to my channel and am glad you love the board 😉

[@jeanjohnson2743]

Thank You

[@KleoYan]

Hi J, welcome to my channel. you are most welcome.

[@gregbrown9647]

I really liked your review...up!!😃😃😃

[@KleoYan]

Hi Greg Browm, welcome to my channel. Do pardon me for the late reply and thank you for your valueable feedback.

[@christoph1313]

Anyone have their bios menu and splash screen change from black to green?

[@KleoYan]

Hello Christopher Naggy, welcome back, use to do that like years ago. Now I don’t think you can do that as UFEI has the tpm and secure boot thing. Maybe try Reddit forum to ask.

[@YummiestOrphan]

Great review but I have a stupid question. How do I get into the BIOS? 😂 The pc loads so fast I can't even read what it says 🙃

[@KleoYan]

Hello YummiestOrphan, welcome to my channel. the moment you click on restart from windwos or did a cold start on your PC, keep pressing the delele key till you see the BIOS.

[@YummiestOrphan]

@@KleoYan thank you my friend 🤟🏼

[@KleoYan]

@@YummiestOrphan you are most welcome, all the best with your build.

[@Patrick-pv4ud]

Nice Board i have always a Asus Borad but i wait for next year price drop. Thanks Kleo Good Video. I buy one 2023. Best Regards

[@KleoYan]

Hi Patrick, welcome to my channel and thank you for your valuable feedback. Hopefully they will drop prices of to have some sales. Then we willl benefit 😬

[@Patrick-pv4ud]

@@KleoYan yes i hope

[@KleoYan]

@@Patrick-pv4ud hi. There will be. Just need to wait for good deals 😉

[@Tehntex]

"Hi, could you please help me? I’m building a PC with 3 fans from an AIO cooler and 4 case fans. Do I need a fan header hub, or will the motherboard have enough headers?

[@KleoYan]

Hi Jesaja, welcome to my channel. Maybe list down the AIO Cooler and the fans you are using, I will need to know the brand and model to check the Ampere of those fans.

[@Tehntex]

@@KleoYan The case, an ENDORFY Arx 700 ARGB, comes equipped with three pre-installed basic fans. For cooling the CPU, DeepCool LS720 AIO liquid cooler i will use. Thanks you very much for your response and help.🙏🏼

[@KleoYan]

@@Tehntex for the LS720 AIO, the ampere of each fan is at 0.29A which you should not have an issue as 3 x 0.29a is at 0.87A, this motherboard CPU_FAN is at 1A so it's ok. as for your case fans, I have no idea what's the ampere. can you check on the fans if it does shows you the ampere used.

[@Tehntex]

@@KleoYanokay

[@KleoYan]

@@Tehntex most welcome.

[@rigomeraz9340]

Nice video

[@KleoYan]

@@rigomeraz9340 hi ya and welcome to my channel. Thank you for your kind words and all the best with your build 😉