Audi S Tronic Gearbox Problems

[@pravardhanus]

I don't know who in Volkswagen group asked the engineers to use such a large hybrid circuit (based on ceramic substrate) to use it in car transmission where the vibrations are too much. I know ceramic have better heat dissipation than a FR4 PCB but they can't handle vibrations if it's not attached properly and also it has to be hermetically sealed.

[@antm2296]

Just bought an A6 Black edition from an Audi approved used dealer. One day into having the car this message came up and 20 minutes later I was stuck in the middle of a junction and it would not go into gear! Had to be towed away. Thank god the car is warrantied for its full term and currently been given another Audi courtesy car. Making me consider terminating my pcp contract while I still can. Just goes to show a car may look great but what’s going on under the bonnet is evidently more important. Never had any problems with my Ford 😅

[@mrmartin2079]

Hi Q5 2012 tfsi 135klms Had parking break malfunction come on/ off once a month for a few months This week epc came on with Stabilization programe fault - see owners manul ,parking break makfunction and Gearbox Malfunction - you can continue driving Took it too garage ( indy ) He scanned it and cleared the codes ( didnt get the exact codes from him ,but he didnt seem concerned,said i can continue driving ,even long distance) Got the car back - no error showing After driving a little the same GB Malf message came on - then off again Whilst still driving I am based in thailand so any info about what i should do next gratefully appreciated The car seems to be driving normally now I have a long drive planned and am nervous Cheers

[@MdRubel-gy8ms]

Hi sir I'm mdrubel mechnice from bangladsh good information thank you sir

[@urbanjentry222]

Great information thankyou for creating this video

[@m.a.6526]

In Audi A4 B9 (8W) there is no 0B5 gearbox installed! There is the gearbox 0CK DL382 installed!

[@jamesjohn3435]

Hello mate my wife has a a1 2014 never had a issue she jumped started my mates van witch is a good van so probably has 2 battery’s on it…not knowing she should not off but now it want go into any gear and has the yellow warning on the box, we was told it can be caused from the jump start maybe cooked the mechatronic unit is this true thanks as it’s going to be a massive bill…

[@jamesjohn3435]

I meant food van and also her car is 7 speed auto it’s saying valve issue or pressure

[@thepubwiththeboys]

Can you upgrade the A4 B8.5 gearbox with a more performance orientated one from another model?

[@johngraym5517]

What if you only get P179E00 and P179F00 on the transmission?? Once the gearbox gets abit warm it chucks it into Neutral and N light flashes then parking brake error gearbox malfunction continue driving.. I switch the car off to take it out of any gear to put in park.. then switch it back on an can put it in D and drive goes through all the gears 1234567 still has gearbox malfunction cog on dash.. if I leave for couple hours then gearbox light goes off and back to normal till it warms up.. any help and advice would be appreciated.. is it definitely the drive position sensor as I'm splitting the gearbox soon so wanted any advice

[@dambar8056]

Hi I have problem with Reverse Gear on the hill.. When Oil is cold Gearbox work perfect but when oil is hot 80-100 *C In reverse gear, I have to add a lot of gas to make it fatten uphill. I replaced the Borg Wagner mechatronics kit 3 valves + harness errors there are none

[@Ecutestinglimited]

Hi there, our technical team will be happy to look into this and advise further for you. If you can send an email to [e-mail] with your vehicle details, symptoms, fault codes if any are present, a part number if available and any other relevant information, we will be happy to help. Thank you

[@knt2660]

Hey mate I’m just looking at auto a3 2009 plates I heard there’s lots of issues with the gear box just wanted to know if that’s true? Cheers

[@kotkesha]

why no recall case from audi about this common problem on all beginning 2011 cars??????}

[@jimvargas5085]

From California USA what would be the pickup and return shipping costs?

[@Ecutestinglimited]

Hi. All shipping from the USA is $50, however we cannot arrange pick up so you will have to send it to us yourself. Please fill in our online test form to get started: myaccount.ecutesting.com/. If you have any further questions please email our technical support team at [e-mail] and they will be happy to assist you further.

[@Gabriel-km2xi]

In this video is a A4 B9 that has S-tronic DL382 (0ck).

[@alexmotov4]

Good video !!! The Audi A4 2015- which is also featured in the video A4 2015-0CK is the automatic transmission A4 -2014 0B5 which in the video is mechatronic The video is not entirely correct! Hi

[@mortezagachkar6366]

Hi I don't get any fult code when the car is cold it's fine bout when is get hot when I stop get clinking when put to D or revarse

[@meteora8888]

Still issues after so many years?

[@markmcclintoc2077]

Hi, Tim, I have an Audi Q5 2009 just got it about 2 days and the Gears are a bit Harsh and Jerky as you said, and sometimes when you stop the Engine cut out it will restart ok. when you put it in gear if you are too Quick Between forward and reverse it goes in limp home mode do you have a rough cost to fix them and I am in Australia have you done one from there Thanks, Mark

[@mw5961]

Hi , did you sort out this issue with your Q5 ?

[@mtutumasiza2579]

The gears pf My 2020 Audi A6 2.0 TDI wouldn't move beyond 2nd gear. This happened about 3 days after it was serviced for 16 000km at Audi Arcadia in Pretoria. It's now been with Audi for 10 days with NO resolution as they say the do not have the spanner to open up the faulty part. All those days the don't even offer a replacement vehicle for such an expensive car. Totally disappointing! Masiza

[@jarrodwebster8166]

I recently threw codes p060a and p0798. Parking brake and gearbox malfunction lights on as well. Car had to be towed. After a couple days of sitting and battery charge codes are clear. Mechatronic failing?

[@adriandeb2710]

We have a 2010 audi tt 2.0 fsi. We had the box oil change carried out over a year ago but lately noticed on pull away its jerky every thing else is fine, do you think this could be low oil level or something else we have no warning lights car has done about 58,000

[@FinancialRPr]

i have audi tt 2011 2.0 fst exactly same problem

[@bigped845]

I've not long changed my mechatronic unit in my s3 8p, it was holding onto gears sumtimes to long so got a new second hand unit and worked well for a week ore 2 now is starting to creep back in what could this be any help appreciated

[@willywinwin]

audi 2003 a8 4.0 tdi gear shift light dose not light ,does anybody know what the problem might be, gear box performs well and all other eletrics are working just cant sus were the gear shift light gets it feed from it has lit up every now and then

[@swx1188]

Hello. Its possible to have axel joint broken and gearbox shows failure and can’t drive?

[@cipriandanciu8187]

Hello i have audi a6 2016 avant 2.0tdi fwd ,car is not selecting gear,error codes P074800,P07500,P07600

[@Ecutestinglimited]

Hi. The symptoms you are describing could indicate a fault with the mechatronic unit. Please email our technical support team on [e-mail] with the details in your comment above, as well as the part number for the mechatronic unit, and they will advise you further. Thanks.

[@chevrolet1616]

How similar is the Porsche PDK mechatronics unit to the Audi? Specifically talking the Macan and the Panamera.

[@darwincollado8993]

I have a 2018 macan and the internal are identical to a DL501 only the casing and rear tail are different! I have the parts illustrated manual and the parts star with 0B5! Don’t let Porsche fool you! The macan is running on an old transmission! DSG-7 until 2018 and then a DSG-8

[@OneIdeaTooMany]

Do you guys service international customers as well?

[@Ecutestinglimited]

Hi. Yes, we offer a worldwide service so you can send your unit into us wherever you are! Please follow this link: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/ and select your make and model of vehicle for our most up to date pricing. Be sure to check the part number is correct, and if you cannot find your part number on our website then please contact our technical support team at [e-mail] and they will be happy to assist you. Cheers.

[@dnjacel]

i have error code P17D000, what is the problem? diagnostic system says its clutch 2 slip too great Do i need oil change because its long time no change or i need complete new clutches and expensive repair ?

[@zsoltrafael4063]

is this fault code belong to the mechatronics ? i have 2009 audi q5 7 speed automatic P284A00 Shift Fork 'B' Stuck

[@mightymulatto3000]

Any one who is shying away from the TT-RS this is all the reason to pull the trigger for one with the manual gear box here in the US. The multi clutch alone is a $6K job. Timing belt $4K. This Mechatronic unit sounds like a $3K-$5K job.

[@EazyDuz18]

the manual clutch only lasts 10,000 miles, DSG all the way

[@1DJGRAY]

Hi I have a 2013 a5 2.0 tdi auto I have noticed that sometimes I can go to set off in 1st gear and the revs build up and it just crawls along then jumps into gear. The rest of the gears seem fine. Almost like the clutch is slipping? It also doesn't seem as responsive as my Mrs q3 with same engine. Both 170bhp

[@Ecutestinglimited]

Hi. Erratic gear changing can be a sign of a failing mechatronic unit, however we would recommend getting a diagnostic scan to see if any fault codes are being produced before condemning the unit. If you are able to do this, please email the results to our technical support team at [e-mail], along with the the make and model of vehicle, and symptoms of the fault. They will be happy to assist you further and advise you of any re-build solution we can offer. Thanks

[@tonyo3814]

Have you managed to resolve the issue? My 2013 A6 2.0 TDI also does this when cold but other than this the gearbox works perfect

[@ze_german2921]

How do I identify which transmission I have?

[@ferdinandparungao1359]

I have an Audi Q2......does the aftermarket battery can cause to delete the Gearbox ECU program?

[@Ecutestinglimited]

Hi. We haven't heard of a replacement battery deleting any software sorry.

[@ferdinandparungao1359]

@@Ecutestinglimited ....Thanks for the prompt reply and this is true. Audi claims that putting a non-OEM battery was the cause of strong jerking and the need of gearbox software update.

[@ferdinandparungao1359]

Then is it normal that after the correction. There is still Clutch burning smell and according to them it will fade later as you drive.

[@jimmyroos1677]

If u could help Audi Q5 2014 Diesel, the ID card said it's got a G1D transmission, is this the same as a O5B?

[@abahsain]

Hi .. I have Audi 7 2013.. transmission working absolutely fine just I’m getting error Gear is overheating change driving style .. and fault code is P1765 hydraulic sensor 2 adaptation limit reached .. pls advise what could be the actual problem??

[@bordangosic4834]

Hello. I would like to ask you a question about my error code that has aperead several days ago. It says code number P179D00 and by description says "cooling oil valve electrical error"? I was wondering does that mean I have to repair my mechatronic or is it possible to repair just that one fuse on cooling oil valve? Thanks in advance for your help.

[@Ecutestinglimited]

Hi. The error code P179D00 is a common sign that the mechatronic unit is faulty. In our re-build solution, we replace common failing components with our own re-engineered parts, so the fault doesn't re-occur later down the line. Please visit our website for more information on how to send your unit into us: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/

[@davidmyg7825]

Does it apply to A4 2017? This model faces many problems?

[@mikakesti5471]

I have an A5 V6 tdi with S-tronic 7speed. My problem is, that when car is stationary and I select "D", and take my foot off the breakpedal the car tends to "jump" forward and sometimes the engine stalls and go off even. I've noticed that the gearbox is very slow, when selecting "D" wether I'm backing up and then selecting "D", or selecting "D" and go forward! All the gears works fine other than described above, there's no any sounds or anything! If I select the gear by stopping gearshift on "N" for a 2-3sec, then selecting "D", it works pretty much ok? What could be the problem here? 🤔

[@Ecutestinglimited]

Hi. Have you scanned the vehicle for any fault codes? If you are able to get a diagnostic scan, please email the results to our technical support team at [e-mail] and they will assist you further. Please also include your make and model of vehicle and symptoms of the fault. Thanks.

[@abahsain]

Hi .. can you replace hydraulic pressure sensor G194.. for fault code p1765

[@Ecutestinglimited]

Hi, apologies for the delayed response. We do offer a test for the P1765 fault and, depending on the outcome of the test, we may be able to re-build your unit. Fill in our online test form at ecutesting.com to get started, and if you have any further questions please contact us at [e-mail]. Cheers.

[@johnecu2637]

Audi A4 2010 give gear box malfunction on the dash.when scanned it gives me (gear selector 2 engaging process not successfull)what could be the issue

[@Ecutestinglimited]

Hi. Please email our technical support team at [e-mail] with the results of the diagnostic scan, any fault symptoms, and the part number of the unit itself, and they will be happy to advise you further. Thanks.

[@chriswood7165]

I live in Mexico getting. i am getting all the above issues on my Q7. Trouble is nobody here will service the Unit. the cost here for a new unit after Tax is 8000 dollars. I wonder if it is worth posting it to UK then Back to Mexico.

[@Ecutestinglimited]

Hi. We offer a worldwide service so you can send your unit into us no matter where you are located. Please email our technical support team at [e-mail] with the following details. Your make and model of vehicle, the part number of your unit, symptoms of the fault, any fault codes present on the vehicle, and any further diagnostic information. They will be happy to advise you further. Many thanks.

[@chriswood7165]

@@Ecutestinglimited This is great. It's in Cancun now they will get all the info shortly

[@marioguardia2120]

Hello mate. I’m in Australia can that be done here

[@Ecutestinglimited]

Hi. Yes, we offer a worldwide service so you can send your unit in no matter where you are! Fill in our online test form at ecutesting.com to get started. Cheers

[@ChupapiVic]

My 2017 a4 wouldn’t go in to reverse the other day. 😢 I think I now have an idea what could caused it to do that.

[@dreadla2835]

Did you find out

[@dirtbiker8851]

bought my s3 and it’s stage 1 but not sure if tcu is tuned .. i have some issues with mu transmission when i pull off and it changes gear it sometimes have like a jerk in the shift but mostly in low rpm so only when i pull of .. doesn’t happen when i put mu foot down all the way .. any help please?

[@akush42069]

A tcu tune would probably help but I would definitely change the transmission fluid or get it looked it

[@miloslavholy5168]

No wonder you're so good considering 3:19 Harry Potter works for you guys!

[@SP-io5mm]

I,ve got this codes P0914, P0607, P2805, please help Audi A6 2018

[@outdoorcapturingmoments]

Hi , on audi tt mk2 2007 with s tronic gearbox,the car's crawling through traffic around idle RPM and just above, and in auto-selected 2nd gear. It results in a refined ride at this speed being extremely jerky and well, downright embaressing. Is this quite normal?

[@Ecutestinglimited]

Hi. Have you had the vehicle scanned for any fault codes at all? These can help with diagnosing the cause of the symptoms you have described.

[@hossenbasil14]

My car is audi r8 2013 with auto trans obza the gear ingage dirct to 2-speed the fault find in vcds is p073f unable to engage gear one cynchronization gear 1 failed can any help .. thank

[@Ecutestinglimited]

Hi. We can test your unit, however when the mechatronic unit fails it usually brings up more than one fault code, so it's more likely be something external causing that fault. Cheers.

[@robphilip1646]

Can I ship mine to you from Australia

[@gabitzu88oky1]

Hello..I have one Audi A4 B7 1.8t multitronic gearbox 7 gears and I need to reflashing my TCU in my car ..you can help me pls ??

[@stevecardenas8035]

Hello, would total power loss on any upshifting gear for a second or two under WOT be a symptom of a mechatronic issue? I've replaced circuits, and solenoids from the updated transmission and it fixed many issues but that power cut remains. I'm really trying to fix this.

[@Ecutestinglimited]

Hi. This isn't an issue we have encountered before. Have you scanned the vehicle for any fault codes?

[@tylerpadlina943]

i have the same thing going on

[@stevecardenas8035]

@@tylerpadlina943 sadly, i was never able to figure it out. we even took apart the transmission entirely to replace the internal speed sensor for the gears, still no solution. It never gave any fault codes.

[@tylerpadlina943]

i have no idea what to do. mine has very little torque down low and will upshift at a very low rpm even going up a hill. after shifts it will bog and then the boost will come in like a surge. wondering if i should just put a used trans in it? i replaced the circuit boards and clutch solenoids which made it better for a week but now its back to where it was or even worse now.@@stevecardenas8035

[@hossenbasil14]

Hi my car is audi r8 2013 7 speed dsg (0bza) is the part number for megatronic . the fault read is p073f unable to engage gear one / synchronization gear one failed . and car run onley reverse gear and speed 2 and speed 4 can any help .... thank you .

[@Ecutestinglimited]

Hi. Is that the only fault code being produced when scanned? Usually when the mechatronic unit fails it usually brings up more than one fault code, so it's more likely be something external causing that fault. However we do offer a test and re-build service, but again, it could be something other than the mechatronic unit that is causing the fault. Cheers

[@boxingmonthly]

My s5 has a message gearbox overheating adapt driving style, any suggestions?

[@Ecutestinglimited]

Hi. Are you able to scan the vehicle for any fault codes as these will aid with the diagnosis. If you are able, then please email our technical support team at [e-mail] with the following details: Your make and model of vehicle, you transmission part number (if possible), the symptoms of your fault, and the results of the diagnostic scan. They will assist you further and advise you on any re-build solution we can offer. Thanks.

[@szakacsattila9985]

I've got an Audi A4 b9 from 2016 with a 7 speed s-tronic dsg gearbox and I got the message : Selector lever fault but everything works fine,no symptoms at all.Can that be only a sensor error?

[@AlexandruTDK]

I had the same problem around 2 years ago but it’s disappearing by himself and never come back

[@szakacsattila9985]

@AlexandruTDK Seems like I found out the problem.I tested at Audi they did a software update and told me if the message comes back then they need to change the gear knob.

[@geraldvaughan5103]

Send it to where?

[@Ecutestinglimited]

Hi. We are based in Derbyshire in the United Kingdom, but we offer a worldwide service so you can send your unit into us no matter where you are located! Please follow this link for more information: www.ecutesting.com/contact-us/

[@monteZUK1]

I'm going thru gearbox malfunction and am scared to take it on the motorway

[@Ecutestinglimited]

Hi, if you are experiencing the gearbox malfunction then we would recommend getting the vehicle scanned for fault codes to help aid the diagnosis. Please then email the results of this scan to our technical support team, on [e-mail], along with your make and model of vehicle, any other symptoms of the fault and the part number printed on your mechatronic unit. They will happy to advise you further.

[@шрусбатькович-ъ7п]

Hello.my code p17e1 and p17e0.what could be the problem?

[@xhulianobashaj2514]

Hallo zusammen. Ich habe einen Audi Q5 3.0 TDI 7 2013 Gang Automatikgetriebe Facelift- Modell. Wenn ich den Rückwärtsgang einlege, fährt er nicht mehr zurück. Wenn ich Gas gebe passiert da nichts. Als ob es den Rückwärtsgang nicht packen würde. Ich muss dann wieder auf P und dann wieder auf R stellen. Es gibt dann ein Ruck und dann geht es wieder ein paar Meter und dann wieder Bremse und zurück will, geht es nicht mehr. Vorgestern wollte ich aus einem Hof rückwärts raus. Es gab wieder ein Ruck und im FIS kam dann ein Hinweis mit Getriebe-problem. Danach kam das TPMS und Reifendruck-Symbol. Ich habe mein Audi dann abgestellt und nach einer Std wieder in Bewegung gesetzt. Alle Symbole sind dann wieder erloschen. Beim normalen Fahren gehen die Gänge butterweich rein. Nun ist er in einer Meisterwerkstatt und es ist kein Ge-triebefehler zu sehen. Ich hoffe das ich kein neues Getriebe brauche. Kennt jemand dieses Problem ? Über eure Hilfe wäre

[@dickie8184]

German reliability. Fixed by the British, in a shed, while drinking a cup of tea. 🇬🇧👌👍

[@taktak2891]

Hallo , do you have this service in Germany?

[@Ecutestinglimited]

Hi. We are based in Derbyshire in the United Kingdom, but we offer a worldwide service. Fill in our online test form at ecutesting.com or you can contact us via email at [e-mail] to get started. Cheers.

[@arahimbhatti]

I getting 'Clutch overheating, please stop vehicle' and car does not move. Its Audi A3 Stronic 2010. not getting any code. Thanks

[@Ecutestinglimited]

Hi. We would recommend getting a diagnostic scan to see if any fault codes are being produced to help diagnose what the potential cause could be. If you are able to do this, please email the results to our technical support team at [e-mail], along with the the make and model of vehicle, and symptoms of the fault. They will be happy to assist you further and advise you of any testing and re-build solutions we can offer. Thanks

[@arahimbhatti]

@@Ecutestinglimited Thanks, is it possible that no fault code comes on diagnose tool? i got diagnostic done from couple of mechanics but both are not able to get any code from diagnostic scan.

[@Ecutestinglimited]

Hi. If you have no codes present in the TCM, then it is unlikely the fault is being caused by a faulty S Tronic.

[@sheldonbrown438]

hello please i live all the way in Jamaica do you see these unit

[@Ecutestinglimited]

Hi Sheldon, we offer a worldwide service and would be happy to help.

[@warrenwright1904]

Sheldon did you receive any help?

[@mercomemomo2112]

I have problem with 0b5 audi q5 how much you can reparere

[@Ecutestinglimited]

Hi. Please select your unit's part number from this list: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/ for our most up to date pricing. If you cannot find your part number on the list then please email our technical support team via email at [e-mail] with your part number and they will advise you further. Thanks.

[@florincenusa7507]

Ii trebuie facut schimbu de ulei si filtre si sa vezi ca apoi este ok

[@cristian_roblox_gaming2024]

How much to rebuild the mechatronic from Audi A6 3.0 tdi quattro S-tronic gearbox please.

[@Ecutestinglimited]

Hi - head on over to our website with your part number to get a price for rebuild and shipping

[@SOL3YCEEGAMING]

How much was it

[@chrisleon27]

Hello, fault number P177500 CVT 2011 Audi a4 , can u fix it?

[@Ecutestinglimited]

Hi. Please send your details into our technical support team at [e-mail] and they will be happy to advise you. Cheers

[@chrisleon27]

@@Ecutestinglimited OK thank u

[@belminization]

My a3 2011 is shifting harsly in to 2 4 6 gear could this be the mecatrnic?

[@Ecutestinglimited]

Hi. Harsh gear changing is possibly a sign of a failing mechatronic unit. If you email our technical support team at [e-mail] with details of your car make and model, mechatronic part number, and any fault codes or diagnostic information you can get, then we will be happy to advise you further. Cheers.

[@thomasrobinson2746]

Hi bud I've got 2015 Audi A4 Avant CVT automatic gearbox 2lt diesel.. I'm having a issue with it starting from a slight hill it will take of on bidding point but when you stop and put your foot on peddle it will go nowhere then it will kick and take of doesn't happen every time but I've just realised that you take foot of and on again it's ok...any help would be great thanks

[@Ecutestinglimited]

Hi. Are you able to scan the vehicle for any fault codes at all? Without these it would be difficult to diagnose the cause of the fault. Cheers

[@thomasrobinson2746]

@@Ecutestinglimited hi yes scanned the vehicle no fault on gear box

[@Ecutestinglimited]

@@thomasrobinson2746 Hi, if there are no fault codes being produced then it will be tricky for us to properly advise on the cause of the fault. The best option would be to take it to a garage and having them troubleshoot further. Apologies.

[@thomasrobinson2746]

@@Ecutestinglimited Hi yes that's great thanks for your help

[@ln5747]

That sounds like normal multitronic behaviour, how long have you had it? It can be slow to react on a hill and a bit juddery/clunky but you get used to it and how to drive it. Had mine for 6 years/75k miles and at first I thought there was something wrong with it.

[@christopherephraimmbokane]

Hi how can I contact you got problem with cvt tcu

[@Ecutestinglimited]

Hi Christopher. You can either email us at [e-mail] or call us from 9am-10pm (GMT) on [phone].

[@tresurekings22]

Can i ship from the US?

[@Ecutestinglimited]

Hi. Yes we offer a worldwide service so you can send your unit in no matter where you are located. Please fill in our online test form at www.ecutesting.com to get started! If you have any questions please contact our technical support team via email at [e-mail] and they will be happy to assist you. Thanks

[@alexanderstefanxandraswedi5835]

good job

[@lambodude]

What is your contact information please. Dealing with a mechatronic issue on a 17 A3. Thank you

[@Ecutestinglimited]

Hi. If you would like to give us a call, our telephone number is [phone] Mon-Fri 9:00am-10:00pm (GMT+1), and our email address is [e-mail].

[@usef2003]

Hi I’m based in Dubai. Can I send you the mechatronic device and you guys fix and send it back?

[@Ecutestinglimited]

Hi. Yes we are able to re-build and send the mechatronic unit back to you in Dubai as we offer a worldwide service. Fill in our online test form at ecutesting.com or you can contact us via email at [e-mail]. Cheers

[@sehmusbilge9570]

Hello, I have such a problem with my vehicle And the service could not solve the problem, I would be very glad if you could help me AUDI A4 2016 2.0tdi quattro gear selector lever basic settings not made Error code: p287b00

[@bradley8300]

Mine went faulty on my S4. It cost me 5K to fix. It only had 70,000 ish miles on the clock

[@slo.asf.s386]

How much for the rebuild

[@Ecutestinglimited]

Hi, enter your part number on our website for a re-build quote: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/

[@Sebastian-tx9ft]

I took my 2011 Audi S4 to an Audi dealership because of a clunking noise at low speeds and reverse. The car shifts fine from what I’ve noticed. I took it to Audi and they said my car was completely fine and the noise I was hearing was due to the age of the vehicle. That noise got progressively worse. What could possibly be the issue?

[@JoshSmeda]

Depends where noise is coming from, possible suspension issue?

[@phillipforrest462]

Driveshaft

[@mightymulatto3000]

Does your vehicle not go into reverse until you stop and restart? Do you get a blinking gear indicator on your cluster? If you are getting an unexpected gear disengagement code with a car over 32,000 km then your dual clutch is toast. $6K to $7K bill incoming. That said there is something you can try first. That being the DSG service. The car will do this if the clutch overheats. Changing the gear oil and the filter could help.

[@davidfallon4899]

Does anybody experienced this audi a6 2013 S tronic. When I take off it jerks after it doesn't do it until I take off again. Then it's fine fluid has been changed and it has been recalibrated??

[@nickmiranda8761]

@@davidfallon4899 If it’s at low speeds 1-to 2nd shift feels jerky and when you are stoping and down shifting does the car lurch forward and feels hard to stop a bit It’s the transmission bushing gotta get a solid one, it’s like 50 bucks and its two bolts easy 5 minute job fixes all that believe it or not

[@nikeca9834]

Hello ppl, i drive a4 8k5 2012. When i use Sport mode (S) i get this gearbox fault and i need to stop to reset the car. can any1 help me .

[@JesusBarcelinia]

How much mechatronic

[@Ecutestinglimited]

Hi. For our most up to date pricing please visit our website and select your make and model of vehicle and then the part number that matches your unit: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/ If you can't find your part number on our website then please email our technical support team on [e-mail], and they will advise you further. Thanks.

[@mrd799]

My s6 has a problem, getting code P189200. basically, i have to start in N, if i go from N to P then the its stuck in P but looking at the letter its in R, But car wont move so i guess its in P also, to change from P i have to switch off ignition, and start ignition again, then i can put it in N and start engine, then down to D to drive, sometimes i cant get it to D, i have to stop start stop start stop start and then it gets to D, weird thing is this is not always, its random, and when it doesnt work it doesnt work for atleast an hour. however the stuck in P part is always happening, Any help would be appreciatet, one person said it probably can be something that is in the gear box that changes the gear selector thing, because it drives smoothly on all gears otherwise. opening up the gearbox would probably be very very expensive

[@mightymulatto3000]

Take your car in and demand they show you GFF (Guided Fault Finding) in their ODISS software. If they don't have ODISS, run!

[@juanpicado9964]

Hello I have a Audi q5 quatro 2.6 I having issues with the transmition do you have a repair shop I will like you guys to check it

[@Ecutestinglimited]

Hi Juan, we offer test and rebuild of electronic control units

[@natalietan3177]

If the reader shows a mechatronic fault. Is it a must to replace it? As the car is working perfectly fine

[@chronicle5719]

Help pls what about P02700 code?

[@Ecutestinglimited]

Hi. This isn't a common code we have seen when the transmission is failing. However if you suspect the mechatronic is at fault then please email our technical support team on [e-mail] with the following details. The make, model and year of manufacture of your vehicle, the symptoms of the fault including fault codes, and the part number printed on your unit. They will be able to advise you further. Thanks.

[@Arturofernandezslc]

How much is this ?

[@Ecutestinglimited]

Hi. Follow this link: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/ and select your vehicle model/part number for our most up to date pricing. Cheers.

[@wojciechkanclerski]

A4 B9 2019 2.0 TFSI with 0CJ transmission... I regret buying an Audi... throttle lag is freaking frustrating.

[@captainjeff6562]

I just recently got a 2010 audi S4 and when I floor it from a stop it will shift from like 1-2 or 2-3 and have a long delay. Does anyone know what this issue could be?

[@siyarahmad908]

Sell it. Even audi dealer can’t fix your problem. Audi is scam company

[@DroneLegacyUk]

Hello, i have an A5 3.0 TDI 2011 and every time i stop at the light, the RPM goes from 600 to 800, to 400 and sometimes the engine just turning off. It does this every time, i ve been to so many mechanics but they can't see the issue. But trust me, i cannot drive it like that, it make me sell it. Can you tell me what this can be? Thanks

[@canihazburgers]

Im getting a bouncing throttle and the car jerks when stationary as well. It doesn't stall but wants to and then the revs go up to about 1000 after dipping to 500 etc. This is a 2010 S5. So annoying!

[@winstonmcleish9602]

Hello, I’ve had fault codes 18004 - Gear Selector 4, P187D AND 18044 - shift Fork 4 position sensor, P2848. Any ideas please. Car is a 2014 B8.5 S4 Audi.

[@Ecutestinglimited]

Hi. With those fault codes being produced, it is unlikely that the fault will be with the S-Tronic control unit itself, and rather with something within the gear box. Cheers

[@lovelymckenzie3710]

were u able to solve ur issue..i have same problem

[@winstonmcleish9602]

Problem not solved at present. Audi specialist only offer was to replace the whole gearbox at £13.000. Four Gearbox specialist have indicate different solutions to the problem, from wiring loom, to mechatronics. None of the garages have indicated there solutions will definitely work but say it’s a process of elimination. I have the care scheduled for repair on the 29th June.

[@vytautaskryzius2556]

@@winstonmcleish9602 did you got it fixed ?

[@CaptainGondwe]

Your helpful

[@wipopsiri6152]

I have 1 go 3 go 5 go7 why 😭😭😭

[@PSCupraFormentor]

Can anybody answer me some stronic concerned questions please? 1) Can I change D to S and back to D during driving without any other steps? 2) What if I'm in situation, where I'm accelerating a little and "need" a downshift? Can I use paddle to shift down while pushing the gas pedal without causing any harm to the transmission? 3) In manual mode I'm pulling up the car on a light stop. Can I stop the car on 2nd gear and then downshift to 1st gear when the car is stationary? Or should I shift to 1st gear sooner due to RPM? 4) Is it normal to hear the shift from 2nd to 3rd gear with no load? Can't hear any other gear change other than 2 to 3 and even that is with almost no load. Under the load everything is silent and all I can hear is the exhaust. Only 70k km on the gearbox so far. If the described situation isn't completely normal, what is to blame? Mechatronic part? 5) Should the transmission be completely smooth in a car from 2010? Sometimes when the car goes without pushing the gas pedal I can notice a little lagging on the 2nd gear. I can imagine this is a nature of the older automatics transmissions, just wanna know :-) Thanks, P.

[@Pulstate]

I'll try answer some of these. 1.) Drive and Sport modes can be seamlessly swapped between during driving. 2.) You can downshift using a paddle which will bring you into 'manual' mode and then accelerate as normal. The S-Tronic will then revert back to D mode after a few seconds. 3.) You don't need to downshift into 1st in manual mode, the S-Tronic will do it automatically. Downshift as normal to 2nd then when coming to a stop, it'll automatically go into 1st. 4.) Will need more details on the sound. When you say 'hear' the shift, what do you mean? I sometimes hear a noise from 1st into 2nd on my S-Tronic which has been there for a long time and caused no problems. 5.) Cars up to 2014 (when Audi introduced the newest generation of Mechatronic design) can all be susceptible to problems. Audi also left this gearbox behind and opted for ZF's 8 Speed transmission as it is much more reliable. The smoothness of your transmission depends on your mechatronics being healthy and your clutch packs not being overly worn. A failing mechatronic unit tends to damage clutches as-well so it's a 2 for 1 scenario. (You change out the mechatronic, you generally do clutches as-well). Hope that helped.

[@veronicaferraro9556]

in reality , the DSG will never be Super smooth , like a regular Auto transmission . it is essentially a clutch engagement you feel .

[@morgandrives]

Can’t help with 4 and 5, but I can a bit with 1, 2, 3. 1. Yes. 2 and 3 are similar. You need to out-think it in a way, understanding it is always in 2 gears at once, trying to predict your next move. 2. If you want to down shift, let your foot off the gas for a second, it will anticipate a downshift so when you do it it will be instant. If you try to downshift while accelerating you confuse it because it is ready for the next highest gear not the lowest. 3. It took me a while to learn this one. You have 2 options when in M and coming to an stop. Just leave it in 3 and come to a stop slowly. It will understand you want 2 then 1 and do it smoothly. Or, if you have shifted to 2nd, come slowly to a stop, easing up ever so slightly on the brake as you stop - this gives to time to move from 3-1 on the 1-3-5 clutch/shaft. If you downshift to 2 and stop right away, it has trouble because it was ready for 3rd. The adjustments are small but important. It was hard for me because I drive manual cars mostly, so some habits had to be altered. Hope that helps.

[@syedmesfer1879]

Hi i am frm India Diagnostic Engineer in MB. Can I have a delarship in INDIA.

[@stringer6435]

iv had problems since audi serviced the gear box? i keep getting the fault shift to P before leaving the vehicle

[@Ecutestinglimited]

Hi. Are you able to scan the vehicle for any fault codes at all? Without these it would be difficult to diagnose the cause of the fault. However if it was working fine before the service then we would recommend bringing up this problem with the garage that carried it out. Cheers.

[@abahsain]

Pls provide tentative cost for repair mechatonic for Audi A7 2013

[@Ecutestinglimited]

Hi. Please select your car make and model on our website here for the most up to date pricing: www.ecutesting.com/common-faults/audi/audi-s-tronic-0b5-gearbox-mechatronic-problem/ Thanks.

[@abahsain]

@@Ecutestinglimited I live in Dubai ..

[@Ecutestinglimited]

@@abahsain That's not a problem, we offer a worldwide service! Fill in our online test form on www.ecutesting.com for more details regarding shipping. If you would like more information on this, please contact our technical support team at [e-mail]

[@abahsain]

@@Ecutestinglimited thank you .. fault code is P176500 hydraulic pressure sensor 2 adaption limit reached..is it a valve body is damage??

[@himanshutanna711]

@@abahsain Hi Bro did you resolved it. Need your help if you did. I’m in Dubai too.

[@Golfr2020]

Should never happen on a premium car, reason why people pay so much for them. Cheaper cars it seems are often more reliable

[@sasothestrategizer]

There’s always the tiptronic!!

[@DrMarioLuisBalcazarGanem]

he tenido 2 Audis : A1 (2013) y A3 (2017), ambos con falla catastrófica ( cambiar la caja ) antes de los 100,000Km con todos servicios de agencia . Adiós Audi , me voy con Tesla pronto !

[@monteZUK1]

Thank God Audi is not in airplane manufacturing Looks like they should close down

[@z06dave]

God I miss my 6 speed manual. First DSG I buy and I get fucking mech problems. Urgh

[@anthonychevy2078]

My friend literally just traded his 2019 Camry for a s4 yesterday and the transmission broke on him just hours after getting it smh and they both just hit 80k.

[@siyarahmad908]

Audi dealer have changed the whole mechatronic unit after 3000 miles still experiencing the same jerking gear, and still getting gearbox malfunction . Audi dealer has denied to repair and get responsibility. . Audi is scam , I will not buy audi

[@slinkyslk]

how did this story end ? thanks