1998-2006 Audi TT 8N Window not sealing when you open and close the door? Watch for more info!
Пікірлер: 48
@runningboots111 ай бұрын
Thank you so much ! Excellent tutorial - my son watched it too and helped me complete it. I used some thin rubber instead of the hose clip but it is a nice snug fit now. Drop, lights-on alarm, courtesy light and door open notification now all working. 👍🏼
@Croi_Fiain5 жыл бұрын
There are a lot of TT forums covering this in text and photos, but this is the first time I've seen a decent video on how to do this - it looks a lot easier than I thought. Thank you so much for posting this! Really useful :D
@currentcreation5 жыл бұрын
You are very welcome! Glad I could help!
@familyfun94745 жыл бұрын
Thanks to your video, I repaired mine. I used a 1.50 switch from radio shack online. Had to make a few modifications but it works.
@xNachoPandaXx4 жыл бұрын
hey man BEEN looking for about 3 years for a video like this good shit gonna try and see if this works on my passenger side window
@currentcreation4 жыл бұрын
Good luck!
@eyderfrancoospina76152 жыл бұрын
Hey, 19-December-2021, and this video was really useful, thanks a lot for your time and your video, i just repaired mine, great video!
@carlover97644 жыл бұрын
Thank you ! I just remove driver door lock and it have same exact problem like yours. I follow your metod and i fixed it, thank you very much.
@jacquesgouws5 жыл бұрын
Thank you! Seems easy enough. One guy said T25 you say T30, will figure it out when I get there haha
@TheBanks2745 жыл бұрын
Thanks for the video. My driver's side door has been driving me nuts with this. Going to try fixing it up now!
@currentcreation4 жыл бұрын
Good luck, glad I could be of service!
@dampf-gerry4 жыл бұрын
Thank you for this explanation! Greetz from Germany ✌😉
@currentcreation4 жыл бұрын
Glad to help!
@mrcharlesbenjamin5 жыл бұрын
Great video, I have got to do mine, on the tt forums alot of people glue a small strip of plastic (from a yoghurt pot or similar) over the microswitch.
@mrcharlesbenjamin5 жыл бұрын
I managed to do it without removing the door lock itself. Remove door card and you can see the switch, i had to snip the plastic below the switch to allow me to get the clip out but was a half hour job
@Spence_Bo4 жыл бұрын
How are you installing the hose clamp?! Are you cutting it and forcing it in the mounting position or is the clamp screw mechanism just not visible in this video? You've got me pulling my hair out because I need to do this and am unsure what you're doing on this video. Thanks for doing it...please answer asap.
@filipposcalia50003 жыл бұрын
Is it a XZN key to open le side?
@georgeeversham44334 жыл бұрын
How do you disconnect the main wiring harness that runs off the door lock mechanism?
@currentcreation4 жыл бұрын
It is a typical wire harness used with VAG cars. There is a little tab on the side that needs to be pushed. Sometimes they are broken and you can just pull the harness loose, or may need to get a small flat screwdriver to slide under and lift the tab piece up a little to release. The end of the harness connector, that is part of the mechanism, has a little plastic wedge that the loom part of the harness grabs onto.
@subaru46742 жыл бұрын
I got audi TT MK1... Why can't open the door after lock
@angelesworld38556 ай бұрын
Could you or anyone here be able to share how to replace the boot lock latch on audi tt
@seids75985 жыл бұрын
hi how did you disconnect the metal wire iside which is connected to the door lock?
@currentcreation5 жыл бұрын
Turn the connector 90 degrees and it slides right out
@isak25784 жыл бұрын
Thank you for this video, great material! :) I have a question. My driver side window has the same issue with the edition that in won't go down or up at all using the finger switch. Like when you open the window normally. I can't hear any relays clicking when i push the button. Do you have any idea what this could be? Wiring from the door to the inside of the car? Burnt motor? Any way to check this? Thank you for any replies :)
@currentcreation4 жыл бұрын
Sounds like the motor. I have another video that I haven’t produced yet, where I handle a full regulator repair. I will try to get that up soon, but in the meantime I suggest testing the motor. Could just put a volt meter on the motor harness to find out
@isak25784 жыл бұрын
@@currentcreation Thanks for the answer. You don't happen to have a wiring diagram? or is it simply two wires?
@currentcreation4 жыл бұрын
www.bentleypublishers.com/audi/tt/2000-2006/Audi-TT-2000-2006-Repair-Manual.html page EWD-43 & 44 are the window wiring diagrams. Bentley is helpful if you need a diagram. Can’t recall how many wires, I would just test the signal on all of them to be sure that you are getting a signal to the motor. Could also pull the motor off and test it. Chances are pretty good though that if your motor is bad, it’s due to drag on the regulator. You may need to replace the whole thing.
@filipposcalia50003 жыл бұрын
Where can I buy the exact micro switch? I've seen it on AliExpress and eBay but I don't know if it is the right one.
@currentcreation3 жыл бұрын
Someone else said they found a replacement at radio shack. The whole reason I tore apart the mechanism to repair it was because I couldn’t find a factory replacement. Have to replace the whole mechanism.
@familyfun94745 жыл бұрын
Thank you! How hard was everything to re-install?
@currentcreation5 жыл бұрын
Not hard. Install is just reverse of removal. Only a few screws and the wire harnesses to connect. The door card on a TT is incredibly simple to install.
@familyfun94745 жыл бұрын
@@currentcreation thank you again. I was having issues with the door handle connection. My switch had the rubber broken away. The plunger is gone. Now I am on the search for a micro switch that I can make work. Thank you for the great video!
@currentcreation5 жыл бұрын
Family Fun you’re welcome! Hope it helped. Be sure to like and subscribe. There will be more to come!
@BlockchainToTheFace5 жыл бұрын
My door locks on both Doors spin round and round and will not lock. Any ideas?
@currentcreation5 жыл бұрын
sounds like the flat metal piece on the mechanism isn't turning with the key? maybe not lined up properly? is the flat part inserted into the slot on the door handle end? The first thing I'd suggest removing the mechanisms from the door; to see if they are assembled to the door correctly.
@user-bf5xu9wl5j2 жыл бұрын
Тоже делаю подобную скобу , но из полоски пластиковой бутылки. Резину не счищаю и по пластику скользит лучше и не изнашивается.
@beaucottington5 жыл бұрын
will this cause a neg draw on battery while not in use? I think i may have this problem
@currentcreation5 жыл бұрын
It could cause the alarm system or maybe the radio to use excess energy when stuck in the open position. So Yes, this could be your problem!
@beaucottington5 жыл бұрын
current creation so if my windows aren’t adjusting on door open and close, can I assume both sensors need this treatment? It’s only a 70ma draw on my battery, and the need to disengage the door open sensor to do a multimeter parasitic draw test pulling fuses brought me to your video. I’m still trying to figure out how to disengage the door sensor to do the draw test. Any suggestions?
@currentcreation5 жыл бұрын
@@beaucottington first, yes it sounds like both doors need the same treatment. second, when you have the door apart, you can do the test on the switch to open and close the window as seen at about the 6:00 mark in my video. Test the draw before and after cycling the switch and that should hopefully answer your question. Please report back, would like to hear your findings! EDIT: you could also hook up the mechanism to the door and just cycle the microswitch manually while it is apart as seen around the 3:30 mark
@beaucottington5 жыл бұрын
current creation will do thanks for the info mate
@currentcreation5 жыл бұрын
@@beaucottington good luck!!
@elmerlilly32454 жыл бұрын
Dang. You skipped right over the last step of taking it out...the part I was looking for. Where the short wire gets disconnected from the assembly just before you pull it out. I can't figure it out.
@currentcreation4 жыл бұрын
Just turn 90 degrees. Couldn’t get the camera in there.
@1skatersurfer4 жыл бұрын
Anyone have the part number on the switch if it's bad
@currentcreation4 жыл бұрын
I don't believe that the switch is sold by itself. You have to purchase the whole lock mechanism. This is the problem with just replacing it, and the reason I created a workaround. Some have found that replacing the microswitch with one from Radioshack or someplace similar works. You will need to glue it in place for it to stay though. Unfortunately, I do not have any of that specific information. Good luck!