Aussie Review Vevor Brushless Electric DC Motor 48v 2000W

An Aussie Unboxing review of the Vevor Brushless Electric DC Motor 48v 2000W - I will be using this video to make my own electric scooter - E-Scooter, follow the page for all the welding and design ideas to come.
Tags - E-Bike E-Scooter Ali Express DC Motor 48 Volt 2000 Watt DIY Home Build Garage Build Unboxing Unbox therapy

[@DW11111]

the "notchy" feeling is the interaction of permanent magnets in the rotor and the stator

[@kurthammack9867]

Yeah what You said

[@bennysgarageau]

G'day guys, yeah I spoke to an electrician about this and he explained to me the difference between the AC motors we use and the DC motor I have for this project

[@salvaliotta3288]

Love the throw out your Snap on tools.....lol gold

[@DJSekuHusky]

I have that same Vevor controller torn apart right now, as I have to trim the housing down to fit in my scooter, and there's about a 1/2" of material on either side that can be removed without even touching the PCB. I imagine the extra material is to aid heat dissipation, however it will be located at the front of my vehicle where there are plenty of ventilation holes in the deck, so it should be feasible to run a smaller box given my frame's dimensional restraints. Disassembly is really easy: just remove the 8 screws on either side as well as the 5 mosfet heatsink screws on the side, then the whole board just slides out the top. I plan on reassembling it with a bead of hot glue on both end caps for added waterproofing (as I mentioned the deck is ventilated).

[@jasonharrison25]

Correction on the brake wires. Those are supposed to connect to your brake lever switch to tell the motor controller to cut power to the motor when you apply brakes. No regenerative braking on the controllers

[@roystonfairley]

Iv just fitted one on my 3 year old son’s quad bike. We will see how it gos tomorrow. 1st test ride and I will be uploading the footage for everyone to see.

[@shadetreehandyman]

This is the third video I've watched supposedly reviewing this motor and none have actually fired them up

[@Vothtrucks]

You seem to know just a little more about this setup than I do...... and I know nothing !

[@NemesisGrowz]

Feels rough when turning by hand cause of the magnets and coils working against eachother not the bearing 🤣

[@jameskite5936]

Great stuff. Any chance you could send me a copy of the installation instructions you got because none came with my motor. Thanks James

[@ripp3rjak934]

Do these motors heat up or overheat?

[@notfrishpy9043]

Would it work for a mountain bike

[@yourfactstory]

My vevor 2000w phase wire get really hot! Normal or too heavy load ?

[@A.Dotin4K]

Can I use the motor alone with my own speed control knob and plug it in? Will it work? I don’t need those other parts. I’m using it for a different project.

[@Jsosodke]

Can you change speeds ? The r site says it’s a 3 speed but I can’t see in the video how to switch them

[@BeeEmmW]

Hi there. Can you tell me if the motor has a fan built into it?

[@bradenveale291]

can i get the link from where you got this motor kit

[@almuhito]

Hi, Do you recon if this motor can be mounted facing down on an outboard? I am thinking of converting my petrol outboard to an electric one and would appreciate your comment since you have dealt with it.

[@rod8652]

don’t know if u still respond but if u check ur hall sensor, is there a missing wire?

[@Blinkeu_Y0T]

can this be installed on bicycle?

[@user-gn8kd5qt3f]

How did all this go for you mate?

[@993kmb]

Has anyone used one of these brushless motors 3000w to power a quad bike. I’m thinking of getting rid of the blown motor and doing an EV conversion. I’m in Vic as well.

[@mario126]

From where i buy this

[@badmonkeyfood]

Nice one Benny. WHat makes the throttle controller garbage? general quality?

[@bennysgarageau]

General quality - very short throttle position, fitment, type of plastic used, type of grips used ect. Also there is only one part of the assy that clamps to the bar end, the rest floats, to me it doesn't appear to be hard wearing. And very importantly for me, not even close to water resistant. I have bought a new one, and am waiting for delivery. I was also pretty keen on getting one with a speed - voltage - battery display

[@tobiasmomsen5410]

I bought that motor for my mini motorbike of ebay and i put 3kw throught it and its sick

[@tomglenn485]

with what controller? and hows the longer term preformance? cheers.

[@uyehtut7122]

HowMuch?

[@birdcam2024]

Low level is Brake regen.

[@kkarnis3791]

Can you build a motorised paddle board?

[@bennysgarageau]

That sounds like a great project idea

[@rakeshkumarelectricmotorre9804]

Can ues car batteries

[@RobbiRocks]

What is a rough price of these?

[@bennysgarageau]

$120-150 AUD

[@Ghostuxx]

Tbh im adding wheels and putting it in garbage can as a body to the actual kart