Autodesk Fusion 360 | Tutorial: Using Multi-Axis With or Without Dynamic Work Offset on a Haas VF2

  Рет қаралды 20,123

Autodesk Fusion

Autodesk Fusion

Күн бұрын

Пікірлер: 27
@TheCroatianPimp
@TheCroatianPimp 3 жыл бұрын
Nice video Richard. Quick, thorough and to the point.
@MrDaniell1234
@MrDaniell1234 3 жыл бұрын
This will help a lot itcomes up on the forum quite a lot.
@richardstubley9651
@richardstubley9651 3 жыл бұрын
Thanks Daniel, hopefully will be useful for some.
@milanparmar6694
@milanparmar6694 Жыл бұрын
Nice video Can you explain how to make Fusion-360 cam programming on non RTCP machine
@milanparmar6694
@milanparmar6694 Жыл бұрын
Non Tcpc Machine
@CAMER_21
@CAMER_21 3 жыл бұрын
Where did you took tool height offsets. ...all tool????
@brianwaayenberg3099
@brianwaayenberg3099 2 жыл бұрын
Can you share the test file? I just picked up a trunnion and dipping my toes into 5 axis as time permits. A good part/strategy that directly indicates if I have my table perfectly dialed in for both physical and cam would be great! Using fusion360 w haas vf2 and tr110 trunnion. I babe drays the trunnion into cam and belive I have it right. Rotory was off by 0.0015” from tilt axis and height was 0.0087” different in tilt axis Center and total height from the published literature. Just need to make some physical parts to verify all.
@misteranderson117
@misteranderson117 Жыл бұрын
You can create a macros, and haas will recalculate shifts.
@dymensional9012
@dymensional9012 2 жыл бұрын
Awesome thanks for this!!!
@aeknarintomDIY
@aeknarintomDIY 2 жыл бұрын
Hello, I would like to know where the number -359.738 came from. Thank and advance.
@elliottgriffiths539
@elliottgriffiths539 Жыл бұрын
I realise that you asked this a while ago, but in case it is useful to others! That figure is the position of the plater in Z. The distance added on the moves that position to the centre of rotation.
@denisvasilescu
@denisvasilescu 3 жыл бұрын
I want to know how to add DWO to my post. I have a Fanuc Robodrill with DWO option on the controller, and I’m using the Robodrill post in the HSM library. But it doesn’t have DWO in it. Please make a video on how to add DWO in a post.
@PM.al.whatmough
@PM.al.whatmough 3 жыл бұрын
On a Fanuc, if I am not mistaken you would be using 68.2 as DWO. This is the Stock Fanuc post supports this. I'll confirm why the robodrill one doesn't
@JV_CNC
@JV_CNC 10 ай бұрын
I use DWO on MAZAK Variaxis J600/5X. This works the same as with FANUC. First place the workpiece zero point as you normally do in G54. Then use G68.2 X...Y...Z.... to move the zero point to the inclined plane in which you want to work. Then add IJK to turn the two rotational axes as this: G68.2 X50 Y0 Z0 I-45 J45 K0 This is one of the possibilities to use G68.2 and is called "Euler Angles". I= rotation around the Z axis ; J= rotation around the X axis ; K= also rotation around the Z axis. Let the arrow of the axis point in your direction to choose a positive or negative rotational angle. Positive is CCW and negative is CW.
@hyperformancellc
@hyperformancellc 3 жыл бұрын
can you show how to do this with just a 4th axis?
@richardstubley9651
@richardstubley9651 3 жыл бұрын
Hi @hyper formance, let's guess that your 4th axis is along the X so an A axis. Your X is easy, just probe the face of the platter. Your Z and Y will be at the middle. This now depends on the tooling you have available. If it were me and I only had a probe, this would be what I would try. I'm also guessing you have a 3 jaw chuck and you have made it run concentric. Ideally we want to touch off the widest 2 points of the platter, but I doubt your probe would reach. So put a piece of very round stock in the 4th axis. The back shank of the biggest carbide end mill you have will probably be best here. Now move the probe down to as close to the centre of the cylinder you have as possible by eye. Do a Y Web probing cycle. This will now set the Y to the centre of the platter in Y. Move the probe now so its at Y 0.0, as we know this is the centre, and highest point of the cylinder. Now probe a z surface, minus the value of 1/2 the diameter of the cylinder you are measuring. And now you should correctly have the XYZ set in the centre of rotation for your 4th axis. In truth your X can be anywhere as there is only 1 rotary axis so nothing to intersect it with, however putting it on the face of your platter or face of your workholding will let you always come off that 1 position so you don't need to set up for every job all the time.
@hyperformancellc
@hyperformancellc 3 жыл бұрын
@@richardstubley9651 fantastic write up. how would I do this if I was wanting to set it on a vice mounted on the 4th axis? a point off centerline?
@richardstubley9651
@richardstubley9651 3 жыл бұрын
@@hyperformancellc yeah, you are going to need to have something thats running concentric to the rotation. Try and clamp something precision round in your vice. Maybe even a tool holder. Now set up a dti in the table and rotate the A axis with the handwheel to check concentricity. Then just tap with a hammer whatever you are using to get it running concentric. It doesn't matter whatever you are using or however you are holding it. As long as its round and is not running out to the 4th axis.
@hyperformancellc
@hyperformancellc 2 жыл бұрын
@@richardstubley9651 I have been using centerline since your comment. I am still just frustrated that I cant use the dwo that I paid for with the machine. am I missing a set up step on the rotary settings page?
@EZ_shop
@EZ_shop 3 жыл бұрын
Good video.
@richardstubley9651
@richardstubley9651 3 жыл бұрын
Thank you, we were asked by a customer how to do this so thought others might benefit.
@EZ_shop
@EZ_shop 3 жыл бұрын
@@richardstubley9651 Excellent idea
@kamilatay1704
@kamilatay1704 Ай бұрын
Couldn't Autodesk find someone who understood what they were talking about?
@BhInsane
@BhInsane 3 жыл бұрын
Just save yourself trouble and buy a real machine like a DMG. I own a VF2 YT with TR160 and its the most useless piece of crap I have own.
@kurtclark8560
@kurtclark8560 3 жыл бұрын
I can’t afford a DMG, and I am pretty happy with my Haas with a TRT160. Would I like a DMG, you bet, just like I would like a Ferrari. Would I buy a DMG? Probably not. I think I would get a much better return on my investment buying three or four Haas machines for the same price. Now if I was spending someone else’s money I might choose differently.
@MorganOliff
@MorganOliff 3 жыл бұрын
I doubt that it is quite that useless.
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
Quilt Challenge, No Skills, Just Luck#Funnyfamily #Partygames #Funny
00:32
Family Games Media
Рет қаралды 55 МЛН
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
Dynamic Work Offsets - Make the transtition to multiaxis.
9:16
What's New in Autodesk Fusion for November 2024?
18:39
Autodesk Fusion
Рет қаралды 10 М.
Don't Fear 5-Axis - Episode 3
14:14
Haas Automation, Inc.
Рет қаралды 179 М.
Fusion 360 Machine Simulation - Machine Builder
7:59
Autodesk Fusion
Рет қаралды 180 М.
How To Get Started With CAM Within Fusion 360 - Tutorial
29:52
Lars Christensen
Рет қаралды 391 М.
5-Axis Made Easy -  Parts 1, 2 and 3
27:49
Haas Automation UK
Рет қаралды 139 М.
START TO PART Episode 6: Finishing Parts | Autodesk Fusion
14:58
Autodesk Fusion
Рет қаралды 2 М.
The Basics of 5-Axis Machining
10:57
Practical Machinist
Рет қаралды 49 М.
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН