Hello David thanks for ATS videos. Where signal cables be connected to the generator .
@jonathansseguya46553 жыл бұрын
Thanks so much continue to teach us
@electreca13 жыл бұрын
My pleasure, and Thanks for watching
@seanakiiki76702 ай бұрын
Thxu, engineer I see some control cables connected on the mechanical interlock, I need more explanation on them
@christimasuwayo71304 жыл бұрын
Hy! Am really like your channel cs you explain from A to Z! keep going .
@electreca14 жыл бұрын
Thank you for watching.
@adnewwolde70313 жыл бұрын
Thankyou about automatic change over swich expertion but the time of sharing is short can you send step by step wiring diagram
@electreca13 жыл бұрын
I'll post it here electrecasolutions.com/
@tumuhimbisegeofrey1569 Жыл бұрын
Is possible to use one relay in automatic change over switch
@localnews23024 жыл бұрын
Hi bro Ur video is vry interesting good explanation...can u send me the wiring diagram of control & load pls.....thks in advanced...
@bensonoduor52764 жыл бұрын
nice video.I like it.can you do another video explaining how you connect/wire the mechanical interlock on the contactor.thanks
@electreca14 жыл бұрын
No problem Expect it
@lekanoshodi39804 жыл бұрын
@@electreca1 I also will like to see how the wiring are done, thanks
@HamseAbdirahaman Жыл бұрын
can you tell us how to size and select the suitable automatic transfer switch
@Gooodluck7214 Жыл бұрын
Is there a way of getting in touch with you sir
@creativemind35622 жыл бұрын
Hello David, I have a 30 KVA generator which has no CAD, it uses ignition key for the purpose of cranking it, how can I automate this? Putting into consideration that there is no signal cable for the purpose of autostarting,, kindly waiting for your feedback
@electreca12 жыл бұрын
This is actually achievable and quite simple, but I cant explain it in the comment I will do white board video for it From this week.
@creativemind35622 жыл бұрын
Thenks alot for the feedback,, am eagerly waiting
@nopseudo874 жыл бұрын
Hi, I'm a great fan of urs, I always watch your videos. However, can u please make a video in details, steps by steps on how to wire a 3-phase change over with phase monitoring, timers, relays, and explain in more details how the electrical interlock is made. Can u also please make the wiring diagram. Will be of great help to me. Thanks. Cheers.
@electreca14 жыл бұрын
Am dropping that *VIDEO* soon..................thank you for watching
@mugishayves90332 жыл бұрын
@@electreca1 is this video droped? For sure it might be helpful to me too. Am ur big Fan always watching to ur videos . Much love from Rwanda🇷🇼
@briansomoire8082 Жыл бұрын
i need control panel classes , how much does it cost
@isaacondieki74682 жыл бұрын
Do u give physical training?
@electreca12 жыл бұрын
Not yet
@creativemind3562 Жыл бұрын
Beside the generator contactor, I can see another terminal block with several wires,, what should be wired there? It has approximately four wires
@briansomoire8082 Жыл бұрын
hello mr electreca , my contuctors produces a very loud humming when generator picks load during blackout, what could be the problem ?
@electreca1 Жыл бұрын
Most likely your contactor coil is dirty, You can open it and clean the armature and iron core, the noise ll reduce signficantly.
@linossinkala78403 жыл бұрын
Super
@ifubaraboyerowland84903 жыл бұрын
Thank you, good work, please can you give me the connection diagram and the schematic diagram thank you
@mcgarrysteve4742 жыл бұрын
Are you from Nigeria?
@electreca12 жыл бұрын
No
@ezekielozimi2 жыл бұрын
Thanks for everything, is there a circuit diagram?
@electreca12 жыл бұрын
I will arrange one, Thanks for watching.
@lewiswambugu9271 Жыл бұрын
@@electreca1 did you arrange one?
@yoniseid1180 Жыл бұрын
Sir Please do us.
@007videos92 жыл бұрын
thanks alot exactactly what i needed
@electreca12 жыл бұрын
Thanks for watching.
@ayindeadekunle80032 жыл бұрын
Good experiences
@creativemind35622 жыл бұрын
A light company with appliances totalling to 170 Kw, what size of generator does it need interms of KVA
@electreca12 жыл бұрын
170 kw (load demand) lets consider Power factor of 0.80. (note most alternator manufacture consider PF of 0.80). 170/0.80= 212.5KVA, its difficult to get a gen set of that rating. These are generator sizes mentioning but few 100,150,165,200,250,300,350,350KVA 250KVA is ok but if there is possibility 300KVA is fine.
@creativemind35622 жыл бұрын
@@electreca1 thenks alot for the feedback
@perminuskaranjawanjiru98843 жыл бұрын
Hello.. How do you connect the generator to start and stop
@theultimategamer2163 жыл бұрын
Hey, thanks for the great videos, how can i get in contact with you?
@electreca13 жыл бұрын
You can contact me here electreca.workshop@gmail.com
@ekauhenry61783 жыл бұрын
Is it normal for contactor to become hot
@electreca13 жыл бұрын
A contactor can only be WARM under normal operation but HOT under abnormal conditions like under or high voltage, contact failing to open or close when it's engaged, dust and carbon between contacts.......etc.
@philipmusyoki16874 жыл бұрын
Kindly show how to do the wiring
@electreca14 жыл бұрын
Philip thanx for watching, I'll make it available soon.
@yeshinorbu42824 жыл бұрын
@@electreca1 sir that generator project work is very excellent but i need step by step explain about the components
@thaa_Chief3 жыл бұрын
What's the name of boxs
@electreca13 жыл бұрын
Wht do you mean by NAME OF BOXS?
@SolomonKinyanjui_sk4 жыл бұрын
Hi would you mind to send the circuit diagram
@electreca14 жыл бұрын
kzbin.info/www/bejne/b6Osk3aEotqqjtk at the end of that video there is a circuit........... let know if you understand it.
@SolomonKinyanjui_sk4 жыл бұрын
@@electreca1 Ok i have seen it altho' i wanted to see the schematic diagram of this video especially the relay.
@electreca14 жыл бұрын
@@SolomonKinyanjui_sk ok ill find some time and draw it for you.......drop your email here