Automatic Water Level Controller DIY + PCB Design & All steps of making 230V AC

In this video I am going to show you how to make an Automated Water pump control system using several electronic components including PCB Etching, Drilling and Toner Transfer Methods of PCB Designing. This circuit can be connected to your 230V AC water pump since this circuit use a 230V 12V Relay contact.
First, you should prepare following materials to make this setup.
1) Copper Board
2) Photo paper + Laser Printer
3) Ferric Chloride
4) 12V DC Relay x1
5) DC power connector x1
6) PCB Terminal 3pin x1 2pin x1
7) 8pin IC base x1
8) Ne555 IC x1
9) BC547 x1
10) LED Red and Green 1 each
11) C103 x1
12) IN4007 Diode x1
13) 2.2k Ohm Resistor x2
14) 10K Ohm Resistor x3
15) 1M Ohm Resistor x2
16) Water Pump DC or AC
17) Water Can or Tank
18) Syringe x1
Power Supply #1 used in this video : bit.ly/2H3Haac
Power Supply #2 used in this video : bit.ly/2H6MSbn
Download PCB Design and Circuit: bit.ly/2T1ajDq
Thank you.
Subscribe for more future creative project videos.
Subscribe Here: bit.ly/2JHtlyc
_______________________________________________________________
Track: Unknown Brain - Why Do I? (ft. Bri Tolani) [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Unknown Brain - Why Do...
Free Download / Stream: ncs.io/WhyDoIYO
#waterlevelcontroller #ne555waterlevelcontroller

[@hommakanik7549]

बहुत-बहुत शुक्रिया जनाब आपने सरलता से समझाया बहुत अच्छा लगा ।

[@dineshnaik7413]

Good circuit with minimum components. The contact probs if working on DC power, the same gathers oxcide on them and lose contact of water. therefore the probs supplying power should supply AC power and the sencers should work on that AC Supply.

[@solomizan]

greeting from bangladesh... I was looking for the pcb layout and suddenly got this. thanks for the good work

[@mahmoodshamirzaie816]

Hello and thanks for your interesting video. Can this indicator be used for a tank that is approximately 9m away from the water pump?

[@kalidoss2015]

May i can use this circuit in direct water pump motor in my home ??

[@AmitSharma-pu1lz]

Very beautiful project sir

[@anirbansasmal4942]

Yes it's work. Please make this type another project

[@msandhya8250]

Upto what range of water tanks it can be used...???

[@dasuk7665]

Great job 👍🏻

[@ejtrejos]

Gracias por tu contribución. No obstante, que en la red se encuentran varios ejercicios en los cuales repiten el mismo proceso, acaso no se dan cuenta. Para no ser reiterativo retomo el interrogatorio que se le ha hecho a otra persona que ha publicado lo mismo que tú. "Gracias por un remedio casero tan bueno. Su presentación es muy buena. Quiero agregar una observación a este esfuerzo. Por lo general, el agua se bombea desde el tanque de agua de la planta baja al tanque de agua de la planta superior. El dispositivo que ha explicado funcionará para el tanque de agua de arriba. Sin embargo, debe asegurarse de que haya suficiente nivel de agua en el tanque de agua de abajo. Si esto no está asegurado, la bomba puede funcionar en seco durante mucho tiempo hasta que el tanque de agua subterránea se llene de agua. es una situación peligrosa ya que el motor puede quemarse. Considere agregar otro sensor de nivel de agua para el tanque de agua subterránea. La bomba debe funcionar solo si hay suficiente nivel de agua en el tanque del primer piso. En segundo lugar, Si la electricidad se corta repentinamente cuando la bomba está en funcionamiento, el interruptor de la bomba debe apagarse automáticamente aunque los sensores de nivel de agua den la señal para encender el interruptor de la bomba. De lo contrario, cuando se reanude la energía, la bomba puede volver a encenderse repentinamente. En tercer lugar, debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "". Debe haber un interruptor de aislamiento para esta unidad de control de nivel automático, que será necesario cuando haya una fuga de agua en el circuito de agua y necesite reparación. Esto provocará que la bomba se encienda / apague hasta que se realice la reparación y es posible que no se note fácilmente "".

[@kishorledkarpe3944]

Super video sri

[@Baptist-sf1on]

Good job😊 sir haw can i gat lt pcb

[@balagangadhar8216]

Can you supply pcb with assembled components

[@ahmadsubhi3293]

How add dry protection pump sir in ur circuit,pliss help me

[@kryptoncoder2949]

Working Perfectly (Y)

[@marvinparojinog7120]

It works?

[@himanshutripathi2140]

Pcb manufacturing at reasonable price contect no :- 7065661837

[@leonardogonzalez2465]

excelente video , para poder usar el circuito con 5v que valores de resistencias tendria que usar?

[@mdnayem2651]

Nice demonstration. My water tank is in 5th floor. Will this work?

[@LahisTechLT]

Yes, definitely

[@tigershourov4150]

From Bangladesh 🇧🇩 brother can I use 9v battery for this circuit on 24v relay (spdt)? Pls reply

[@HungLe-zk2qf]

Do I need to replace the 12v relay to 5v? because I have a 3-5v mini pump Help me bro

[@asifmagoon3097]

must include dry run(sump tank empty protection) ..hint use a npn transistor in series of output of 555 and relay driving transistor with its base connect via 10k to underground sump tank (similer probe as upper tank low high) mark the 3rd sensor war(or interlock). atlernate may depower the 555 with the interlock transistor

[@ifthikaruvais4023]

Hi sir tell me how many hp can work on this and up to how many feet tools its work

[@capybara8581]

will it work for 90 watts water pump?

[@kryptoncoder2949]

instead of giving 220V if i want to use DC 12 V battery so can u tell me which things will be changed like resistors or relay? and i will also will be using a dc water pump ...

[@漫i]

Hi ❤ ican use wair vari toll 40 meter

[@AbdulAziz-nx6pt]

Sir lot of thanks for nice job. I have a problem faced with the circuit, when water level touch the Mid sensor then off the relay and when de-touch the mid sensor then relay start again. please help me............. Thanks in advance.

[@nicofilosofo1814]

Same encounter

[@jumbo999614]

After download the pcb in PDF format, do I have to rescale it to correct size?

[@laamvlogger]

Hello bro, after downloading the PDF file, I make the circuit of the pins larger than the components, are you like me?

[@jumbo999614]

@@laamvlogger You mean it's bigger than it should be right? If so, then YES. same problem. If I use Paint program to rescale it, it will lose it's sharpness. It will become pixelated.

[@albatros1230]

Can we use battery instead of dc connector

[@techiesuraj7473]

This circuit only work if u your tank is on 1st floor. I maded and tested it , the relay automatically goes of and on with 2 pins , number 6 pin get automatically threshold if i connect a long wire with it

[@grleon6431]

Can anyone tell me how much amperage of 12v DC current can I push into it?

[@iyantanbuks]

Greetings, I am beginner in electro, schematic that you have shared with us, I managed to run it, but if it pleases, to be added again for when the well water has receded, the water pump engine will turn itself off at its sensor limit, even though the sensor to the water tank gives orders are still filling in, thank you.

[@jatinderkumar1946]

At the 30 feet hight this circuit not working .motor is not cut off.tell me why transformer 12v 500m amp.at this circuit

[@Hamrosamsad]

please add dry run protection if water not rech in tank in 1 minute motor should stop

[@kalidasbaburaobhise5001]

can it works on three phase motor ?

[@ashishrupareliya]

will you sell this with sensors ? 10 minut dry rung possible to protect motor ?

[@isaacsmandigo9179]

Hello. I would appreciate a video or diagram for an Automatic Water Level Controller that switches on the pump when water level is full/High (Overflow switch)

[@gorursuresh4246]

If it is salty water,what type of sensor to be. Used?

[@mgold4685]

etsy (solar well controller kit)

[@martindsilva556]

Hai sir cost of the PCB and components thanks

[@godsons08]

Please explain Pump CONETION

[@KrishnaveniEmula]

What is the range

[@AKGAMING-bb6xv]

Can you give block diagram of this structure

[@bijoyelectronic694]

Thank you

[@amitsharma844]

Can u please explain how to add auto manual switch in this circuit

[@asifmagoon3097]

install simple switch in parallel to relay contact s(com and NO) to operate pump manually directly. switch off for auto...pull out power plug for manual force off

[@RJ-Sri-syam-Ji]

How much Cast it's 10th pics

[@marvinparojinog7120]

Is the circuit connection correct?

[@Gmobilereparing]

Sir agar tank full ho aur mujhe pump 1min chalani ho to kya kari kaha se connection karu kis components k thru

[@LahisTechLT]

connect a timer switch

[@rubanangel5287]

Thank you brother super

[@amitsharma844]

Same question

[@Varun-yi4bs]

Can i use bc548 in the place of 547

[@LahisTechLT]

//Varun // can't

[@amoldange1628]

No explanation of Circuit ????

[@beststatusmaker1852]

Pcb siz?

[@sheikhrony1509]

Pcb design link not working. Please help

[@MH_1624]

You are right..Bro..

[@hewks2007]

where is schematic diagram of circuit ?

[@miscellaneoushub8799]

Will it work for 2 kw motor?

[@LahisTechLT]

230v any motor! Since the Relay is 230v!

[@asifmagoon3097]

use contactor(the pcb relay as pilot duty to connect to coil of other higher ampere relay contactor (atleast 15-20A contacts for 2kw)

[@tusharkantiroy1177]

Price ??

[@buntyGamer101]

Bro iska pcb layout dedi

[@mD-yn9xh]

What abt second tank control

[@mgold4685]

etsy (solar well controller kit)

[@md.aowlad4504]

thanks bro

[@SatnamSingh-kc3tr]

Rate

[@sahinansary8300]

Pcb milga

[@saibalajimv7318]

Pls give circuit diagram

[@bhikhubpatil8745]

भाई पेपर पर कोपर लाईन केसो बनती है पेपर नाम बोलो

[@vishalbharti1271]

How to get pcb layout first

[@LahisTechLT]

it's in the video description

[@JASVEERSINGH-xo8lm]

Hello Sir ye circuit chahie

[@a.ashiqchy]

Hello Sir your Pcb layout link is not correct... And your circuit is not working... I have build exactly like you but relay start with power even all 3 cable under of water... Please help me out by giving proper guide... thanks

[@LahisTechLT]

Ahmed Ashiq Chowdhury It was correct, because I uploaded the same exact circuit that was built in my video. Check the Circuit once again using the method I am showing before the final setup. It should work if you built it properly using exact components.

[@a.ashiqchy]

@@LahisTechLT Sir, please you check the diagram on Google drive & your video, check the connection of transistor you will understand also, I use all same components only instead of 2.2k resistance I used 2.7k nothing else... please share your FB link or whatsapp I will show you...

[@harshitrajsud9hridn]

I also tried this circuit it not working I have same problem

[@LahisTechLT]

@@a.ashiqchy Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap.

[@LahisTechLT]

@@harshitrajsud9hridn Yeah Sorry, Neglect the diagram I've attach here, hookup the connections of transistor as in the video (5.00 - 5.04) , I will attach the corrected diagram asap. All the connections are correct except the transistor.

[@PrienceSiyam-l7w]

Who notice the switch sound😏😏

[@shubhammehra6084]

sir pz circuit digram btayie iska ki

[@SatnamSingh-kc3tr]

Pcb rate caplit

[@jasgaming7826]

Explanation plz

[@santurajbanshi4485]

sir,can i get the PCB from you??

[@LahisTechLT]

Link is in the description

[@mgold4685]

etsy (solar well controller kit)

[@mgold4685]

etsy (solar well controller kit)

[@arikuswoyo]

Skematic please

[@sagarrene]

Bro send me circuit to build in PCB

[@mgold4685]

etsy (solar well controller kit)

[@md.aowlad4504]

pleas gev me this circuit.

[@mgold4685]

etsy (solar well controller kit)

[@balagangadhar8216]

I need 10 nos

[@mdmahabub2249]

আসসালামু আলাইকুম ভাই আপনি কন্টাক নাম্বার চাই

[@irfanmalik1420]

10 Pesh k

[@rameshchandrasita1352]

Send me your pcb

[@lifepuretechnologies7081]

Ye pcb mujhe leni ha 100 Kaha se miljayengi 9045001414 W

[@manzor1959]

.......All the viewers, your kind attention pliz: What if the reservoir tank dries up before the water reaches at the top level to turn off the motor. should you leave the motor run dry for hours and pay a huge bill to motor mechanic to fix it. This idea is totally CRAP, I am an ENGINEER.

[@BokasCom]

m also searching for that will you provide the working circuit ? i tried many but didnot work properly.

[@santdnyaneshwar9920]

Mixing background music in such tutorial videos is very very very bad manners. 👎👎👎👎👎👎

[@irfanmalik1420]

10 peace chahie kitne mein haiy 1peace Aur kab tak mil jaenge delivery kahan per Doge aap kahan per aana hoga mere ko Ek peace ka price kya hai apna contact number send karo please apna contea no sead ko bro OK g... N..

[@tn41creatortech13]

Sir please give the circuit diagram