P0113 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH DODGE JEEP CHRYSLER

[@AutoRepairGuys]

Products that we use and recommend: ►► Intake Air Temperature Sensor: amzn.to/2uz3mQ9 ► Panel Removal Set: amzn.to/3YiMADu ►Torx Set: amzn.to/2hbyWgd ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Engine Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics

[@ultimus1998]

I cannot thank you all enough for your videos and the money you have saved me. It is much appreciated!

[@Sui778]

Thanks for this - my car was throwing this code on my OBD2 scanner after I had gotten the car back for another repair. Turns out the mechanic had forgotten to plug the terminal back in for the air temperature sensor when he put everything else back together. Your video made it easy for me to find the loose plug.

[@biig_tree7073]

This channel is the hand of god

[@AndyTheXTech]

Nice job man. Quick and easy repair. 👍

[@bayfinest1938]

I replaced mines but still have code?

[@zenanskig]

Good video My 2010 Ram throwed this code over after a radio install. Checked and realized the tech didn't plug it all the way back in. Noticed the MPG went from like 17 to 13 too

[@ahopefulvessel]

Thank you for your explanation.

[@lenmcdonald1407]

I've replaced the sensor, it's still reading high circuit, do you suggest that I check the wiring?

[@ilyasahmed2018]

Hello sir how are you I am watching your videos long time I am never miss your videos I like so much

[@alessandrorutigliano6378]

Hi guys thanks for the awesome contributions! Question: I had the same problem with my BMW x5 n52 e70. Same code, same readings with -40, I changed the MAF erased the engine light and it solved the problem; and though the engine light went off the code was still showing in the scanner. This morning I did a live data test again, and the sensor showed -40 again. Any idea? Thanks

[@gunhann]

Hey, what was the problem? The second sensor was also faulty? I wonder if you can tell us the issue.

[@dizzyalyn3651]

Hey guys i have the same problem to Volkswagen CC 2013 2.0Disel 2013 disel. The guys from the shoop says my car have no this sensor 😂. I don't know where to find it. I can't see it but i have same error with - 40°C

[@smartdummy5751]

can't it be that the pcm /ecm is just defaulting to 105 degrees once you put a 'band aid' on the AIT circuit by installing a closed new AIT sensor? it usually sits around 105 when it defaults but when you have a cold snap start like on a cold 40 degree morning the system struggles to start cus a CoolantTS at 40 degrees and a AIT sensor at 105 degrees will cause the injectors to over-fuel at cold start and this can foul the plugs. I would recommend doing a complete diagnosis before replacing any parts. Or you can try your luck and maybe it'll solve the problem.

[@lasvegas70218]

What about for a 2.4 where is it located

[@2fabdad]

If you forget to plug that back in and start the car and don’t have a diagnosis tool can you reset the light another way or will it clear it’s self after so many starts.

[@Jeremiah.1]

You can try to disconect the battery cable red from battery wait few minutes let's said 7 0r 10 minutes and put the battery cable back on place and will work or sometimes while you drive will go off after this procedure

[@CRAULIN]

que fue lo que le hicistes al sensor lo limpiaste

[@trex8468]

Verrrrrrrrrrrrrrrrrrry clearrrrrrrrrrrrrr

[@mckoylach1622]

Can the IAT sensor causes the engine to stall, if it’s bad ?

[@mgtowstanleyzoltanov9808]

I have the same question. But if you ask same question may be...

[@MCMX0212]

I also have the same question,

[@mgtowstanleyzoltanov9808]

@@MCMX0212 I changed it.. it still stalls and gives same error in the morning. Could be the wires. some easy way to test continuinity?

[@troylinkjr5535]

@@mgtowstanleyzoltanov9808 did you ever figure it out

[@reyesfelipe5453]

I have the check engine light code p0113 , change the IAT sensor the engine sputters and died , so I put the old sensor back and the car is fine but the check engine light still there 😢

[@bigcountry7096]

Just spent 100 $ on a new one and it dont work

[@mariovasquez4727]

Great video as always my chrysler town country 2012 3.6 i got it codes p0113 and 2172 I followed but the engine get hard to start any suggestions thankfully

[@isaachimself]

did you ever figure this out?

[@ilyasahmed2018]

Hello sir can you make one video about air suspension Audi A6 A7 any car but air suspension videos thank you

[@mgtowstanleyzoltanov9808]

Where is the air inflow sensor on Ford Transit 2.2 2012?

[@phyllismontana3696]

Need to know how to figure out whats wrong

[@abdoumegrouz5705]

Ford Fiesta p0113

[@blokkafoster3473]

I have this code but my car smells like gas but no visible leaks

[@aaronhernandez3378]

Did you figure it out ?

[@Ceasar91706]

Wow -41° F :-)

[@briancarle]

You need subtitles, couldn’t under what your saying.

[@danielandujar5479]

Slow down your VSS is to fast😆

[@gamerii3697]

I dont know where you from especially from my imaginary country i dont like just like from my imaginary list dont like my country , if you help to my problems im with you justlike "politicians"

[@proreapertv1432]

L mechanic

[@danielvirta1349]

Go russia