AWD Honda Diff Mount || How To AWD Your Honda

[@gtgodbear6320]

Can you lock in awd with Hondas all wheel drive setup? Like weld the clutches or something?

[@SPTuning]

Yes sir :) check my more recent videos. I have step by step on how to do so

[@chalinovilla2848]

@@SPTuning how much do you charge for doing a sling as well as how are you using that

[@mwelke90]

I'd use 2k epoxy primer before spraying the rubberized undercoat and use sealer over the welds. To protect the inside, use a spraywax or fluid film nas. Other than that great work. Greets from Germany ✌️

[@SPTuning]

Good idea! Thanks for the love germany!!

[@garageworm17]

I hope the gear ratio in the front is the same as the back or with in 5 ratios

[@jeffibuilt]

Mounted my diff tonight. So jealous you had that lift! That oddessy Fab kit is nice 💪

[@ryanwolfe911]

I mean this in the nicest way possible, but y'all need some welding lessons lol

[@NSXTACY420]

Agreed.

[@ioohcasper]

!

[@ELLeeOh]

Question: wouldn't it be a good idea to install cv axles to center the diff correctly or do you have to make special length axles.

[@TheBiigBadWolf]

EXACTLY, I would of started with the driveshaft and then the rear axles just to know where exactly im suppose to have the differential at. Second, I would of had it professionally welded because if those welds break.....

[@squanchysquanch7525]

Did any of that actually get penetration? Those welds sounds to cold and dirty!

[@NSXTACY420]

thankyou, another person who feels my fears of those welds, SP tuning REDO them before going an further!

[@stevofla239]

Its fine

[@87mustang347]

I was thinking the same thing listening to them welding. All I kept thinking about in my head was the weld wire dripping on to some of that metal instead of actually fusing into it. I really hate sounded like a dick but man, you have a lot of work into this car to be half assing such important part of the build.

[@hondaservicecenter]

ScienceofSpeed you’re gonna shit yourself when you relaize your entire car is held together by like 50 spot welds

[@joeuno385]

I love the hate on your welds and the "safety" concerns. I mean its gonna be awd so if you lose the rear diff you still have the front wheels under power so most likely you'll still have control of the car. But I'm not a rocket scientist so good luck have fun! Props on the build man I can't wait to see you and all the KZbinr awd conversions hit the track!

[@partypigthefirst]

ah yes, when his diff bracket snaps and the diff falls out of the car and tumbles onto an open highway, can’t wait for some driver who isn’t paying attention to hit a giant chunk of metal going highway speeds. whole accident is then theoretically caused because of someone else’s ignorance. TLDR yes he will have front power to keep driving, but that doesn’t mean the diff isn’t gonna fall out and tumble on public roads. Even at low residential speeds that’s major damage to someone’s car. at highway speeds... well that’s a whole other story. there is no hate, it’s just safety concerns.

[@eksine]

@@partypigthefirst don't worry some people just don't think about anyone else but themselves

[@padraigrab08]

I wanna eventually awd a cl7 euro r Honda Accord

[@matthewpowell8284]

Hey....he's out there doing it. Everyday you get better. Congrats that's awesome keep at it welding you'll get there

[@mket_design]

Wy didn't you grind the reinforced last matal brackets before welding, now your last welding can crack, with the force on the rear diff..

[@GBrai-mu5zy]

I've been seeing this kind of stuff online lately. A few years back,most of the honda forums I saw said that either A: it can't be done or B: it would take a FUCKLOAD of money..... How much will something like this cost now? Are people finally finding ways to really make this a big thing? (God,I hope so)

[@vanessaventura5605]

nice work looking to do the same to my ride is the oddessy diff the strongest of the three choices

[@PowellMoore]

No measurements or test fitting... Hack job fab work

[@eksine]

Shit I was thinking the same

[@josexmckayla]

Talent at work

[@lamarwhite1276]

I want to find a video with an all-wheel drive setup from start to finish EK K swap

[@ClearWater7.62]

Did you guys leveled the diff before welding ?

[@toki89666]

Mounting up my rear diff is going to be quite a pain in the ass. I'm a straight H swap guy and am saving up for one of Few H22 Crew's billet H22 AWD bell housing, it is designed to use the much stronger K series T case, but since obviously H/B/F series are counterclockwise rotating assemblies with the trans on the right or "passenger" side, this means the K series T case will be upside down as its flipped around the other way, this means the driveshaft spins to other way which means whatever rear diff I go with it will have to be mounted upside down. See why this will be a PITA? I don't think I'll even be able to modify a rear diff mount kit, one will have to be fully fabbed up for my dream setup. I reckon drilling and tapping a new drain plug hole will be one of the easiest parts. It is extremely difficult to find any pics of this rear diff mount set up. I can only find a brief video clip only showing from the inside facing outwards under the rear of the car, I wish I could just find pics from the opposite angle as well as side views. Anybody know where Aaron Lopez may have pics or a VLOG of gabbing up his rear diff mount?

[@c10zane]

how do I convert to RWD? do you know of any RWD specific kits?

[@mxro_jo]

You'll need to mount the engine transversely tho

[@DirtyGarageTx]

Do they have direct bolt up kicks instead of cutting I rather not hack my frame in case I ever wanna jus go back to fwd or if I was to sell

[@NSXTACY420]

Please, for everyone's safety next time take a quick welding course at a community college to become proficient before trying to weld in such a crucial piece of a car's drive train that is going to be driven on public roads. Good, professional welds are very crucial for it to stay together correctly and not hurt someone on the road, or YOU , especially if you plan on putting a decent amount of power to it(knowing you, I'm sure it will be very powerful).I'm not trying to be mean, I just have never heard of a inexperienced welder welding drivetrain parts on a street car like its a go kart and it going well. It's not smart to start your welding practice on a car, especially it's drive train. That is somewhat similar to a person starting their welding practice on a Nuclear Reactor. Not to mention illegal when it comes inspection time if it isn't done by a certified welder, unless you just plan to haul it to drag events.

[@SPTuning]

Lol thanks for your concern.

[@bstceltics4]

I've never been to school for welding and i can probably weld better then you so why should someone go to college to learn hownto weld its a waste of time and money when you can learn from by doing it with someone who knows how to weld

[@derekhansen6652]

What inspection

[@joed3339]

your something else bro hahaha

[@derekhansen6652]

@@joed3339 😁

[@crow78376]

What’s your plan for a tank ? We have a rhd crx that we are doing currently .

[@clejmac8387]

What did you do for yours?? I'm thinking of picking up a SI project already in progress thinking maybe a fuel cell?

[@JDMStreetFame1]

Can you put this on a 94 integra

[@jayventransportllc]

A little more bracing to the front mount of the diff wouldn't hurt. I mean, it is all about avoiding any sort of possible twisting when dumping the clutch out of the whole.

[@christopherp689]

This is great. I'd love to do a K20awd turbo but swap it into something goofy. How do you deal with gearing?

[@PetesCreativeRecycling]

CRV / Element rear axles I assume? I really want to see the length change, if any.

[@JohnnyFabz]

Good video as always. Love the crv table 😂👌🏻👍🏼

[@RedneckSamurai126]

Is that a CRV trunk picnic table?

[@cheddar_popz3282]

Did you guys do a mock up first?....this video gives me the impression you guys just went ahead and started welding without thinking ahead...

[@nathanmartin1624]

Said a bunch of times yeah the welds sounded like it needed more amps. But really, that Honda diff is so weak it’s gonna break before those welds do 😂😂👌🏻👌🏻 good luck bro. Looking good.

[@juiceflippin24]

Yo will Acura MDX rdx diff work🤔🤔🤔🤔🤔🤔🤔🤔🤔🤔🤔

[@thestevestandardanthinggoe4170]

Welding doesn't make it a limited slip

[@MrWojg]

Came here to see if anyone else said something about this. He keeps throwing around the LSD term when talking about his welded differentials. This might help SP Tuning: kzbin.info/www/bejne/jZavnmqtfduXrrM I was hoping there actually was some limited slip diff on the install.

[@COMPUTAdotRU]

Hi there ! What is budget for this operation?

[@erick-majin]

Where did you buy custom kit to install the diff?

[@williammfp1567]

Goodnight friend! Sorry for my English, I do not understand the language very much. I have an Accord 3.5 V6 2008, and would like to know if it is possible to leave it AWD, and the procedures or parts to be used on it.

[@kyleholmes7459]

Did you just slap it in, or did you take pinion angle measurements? I guess with no transfer case it would be pretty tough get your angles matching. Or is this not a big deal on the Honda AWD swaps because of the type of drive shaft?

[@derekhansen6652]

Send it and pray for no vibration.... Lol

[@NSXTACY420]

Yea this is starting to go Downhill.

[@stevofla239]

It'll be fine

[@gavincleland9010]

Hm. Aren’t Nylon nuts not good to use on heat areas?

[@adanmendezmoran9855]

Hey how did you get your drive shaft to go from your tran to your rear end thru your sub frame

[@robfrmny21]

I am not hating just stating a fact, but none of you can weld, inspect that crud often cuz there was so much porosity in a lot of that mess.

[@Aqif2016pro]

Hye man,i have a questions my friends just bought accord cl8 and his said his accord is 4wd,is that 4wd cl8 accord come from factory or modifield? thanks for answer.

[@machonation6505]

Finally been wating a long time🔥🔥🔥

[@singlecams]

cut the ends off the long bolts leave like a 1/4" for weight saving :)

[@Manic_Mitch.official]

Ok. And who can i pay to do this for me?

[@joemartinez21024]

What kind of welder are you using I need to get one so I can do the same thing to my CRX

[@HIReving]

Thank you so much! You just gave me an idea on my yellow 1990 Honda crx si, I really need them bracket kit will be using element rear end or maybe crv Please advise

[@SPTuning]

Both very similar. Best being wagon

[@HIReving]

SP Tuning Thanks 🙏

[@ToaistPriest89]

Can you do this with an 8th gen

[@Brian_2JZ]

Great video !!! thanks a lot ! Is this pretty much the same for a EG civic ?

[@SPTuning]

pretty much. very similar

[@Brian_2JZ]

SP Tuning It looks much easier Than I thought. How did You calculate final gear of your rear differential?

[@louisbabycos106]

Would love this on a 2016 v6 coup 6speed manual.

[@mahalaleelforever4806]

I done think the diff is high enough! It looks like it's hanging too low,

[@rgreerjr]

Hey SP Tuning, what rear axle shafts are you going with? Are you able to use factory axles with this kit? Also I looked on the odyssey fab website and I dont see the kit, how much was it?

[@landoski]

Wat drive shaft are you going to be using? And how did u measure it ?

[@wickedsatan1]

Which rear axles and trailing arms?

[@dsmdrew]

So if I’m looking to AWD my 93 prelude si , basically do what you did with the parts you used to awd my prelude?

[@andybhoy2009]

Hey man , I've been wondering after watching your videos , with your AWD setup , have you figured out a way to split the power better due to the CRV diff ?

[@mxro_jo]

It's a 50/50 power transfer?

[@島袋誠-z6k]

So whay hondas qualify for a AWD conversion???

[@ezartperformance2062]

What axle you used?

[@triniwarrior16]

it hangs down low :( would you know if the ek civic awd would be that low?

[@lloyddaroid1993]

Do you sell these kits ?

[@lonelyboysole]

can u take the crv awd diff an put it on to make it awd?

[@qrs3658]

I will love to do a project like this on my 2002 Honda Accord. Anybody makes kits for my vehicle?

[@miguelunknwn]

Has this conversion given you some kind of problem?

[@jakesmith3613]

do you need a new a different transmission

[@marcusgalvan9538]

I looked on odyssyfab website and it didn't show anything for that kit do i have to contact them?

[@colt098]

yeah post a link bro

[@Isaiahhook]

www.odysseyfab.com/product/awd-diy-diff-mount-kit-for-honda-civic-and-acura-integra

[@speedadvocate2764]

@010010000101 010100101 and? Drag racing is not the only type of racing noob. You even writing that proves EVERYTHING. You will see. Keep hacking away.

[@zamiex]

can this fab work with 2 doors ef?

[@SPTuning]

yes

[@zamiex]

@@SPTuning no need cutting my floor pan? i notice that some fab need to cut the floor pan

[@colemontana8695]

What axles are u running wagon ?

[@shhhdontshout]

Is it applicable to 3rd gen prelude?

[@hunterstump1142]

Awesome video bro. You never disappoint. Step by step. Broken down to the T. Keep up the awesome content man. Can’t wait to see this vex in action

[@artfuldodgerlone5384]

I have a 2000 integra gsr I need more info

[@The_Pleiades7]

Isnt the diff still to low though?

[@Eric-steele]

Cool now I can make one

[@khamkham7134]

but for only 225$ for the kit, it's probably more cost effective to buy the kit. some of the features i think could be improved, but if it works, why bother?

[@theycallmekumar6116]

Could i do this to my 2001 Honda Accord

[@carlosnunez322]

Great video bro , keep up the good work 👍🏻👍🏻👍🏻👍🏻

[@dmh11185]

BAM! AWD CR-X!

[@PATuners]

Good Video Car is coming along Nicely

[@makeitorleaveit1]

If them welds had a look, it would be that of a crack head 😅

[@pupo889]

Looking really good man keep it upbro

[@TravisG001]

That is definitely a safety concern...

[@AJIMPORTS]

That kit makes it very easy to mount the diff. Too bad they don't make any for my Body style. Had to cut my trunk out on my AWD swap.

[@gemini3558]

Awesome Pablo nice job mate 😜👍🇦🇺

[@_i-kr6eg]

Why don't people just cut the rear floor pan off a CR -v then cut it up to fit in the civic rear end !!!!??

[@gavincleland9010]

mr323i does that really work? Could be a cheap solution

[@audigybeats]

where online i can get thoses mounting parts

[@ChicoA2J]

www.odysseyfab.com/product/awd-diy-diff-mount-kit-for-honda-civic-and-acura-integra

[@adrianageraldo7621]

Man cant wait to get this stufff

[@gixxr88]

Lol love the crv picnic table evening used

[@victorperez6503]

Hey sp was the differential mounting kit from s1built like the awd conversion trailing arms are?

[@Gbodyteggy1208]

Nice is coming out man one step at a time crx gonna run all 4 wheels boooy!! Nice get yaaa bottles ready.. 👶🔥🔰 ive been waiting for a update on the crx.. ima weld 2 gonna transform a 03 Si seat to fit my integra thing is that is a passenger side seat but iwant a new seat so anything is possible watching u do stuff i think i can do it and make a mission impossible to be possible hehehe...

[@710pappy]

This is extremely interesting 👍🏻

[@civicpride1986]

Very nice.. all this awd conversion cars makes me want to do one😁 hondas ftw.

[@v8consumption]

Looks pretty dope

[@stinky15552]

Coming along nicely Pablo rex looking good dude. This kit looks pretty well done not to shabby coming from Maryland. Parts you had weld was that pretty much it. Can't wait to see how far it sits from the road once lowered some.🖒

[@kzarnold3678]

Nice job.

[@irvsmadhouse]

Dope bro!

[@mrjodude]

With this kit and diff installed can a ASR Subframe brace still fit?

[@psemeq]

it hangs low... you will lose this diff

[@adamsondergaard8159]

Man i cant wait for this thing to rip!!!!

[@scottellis6438]

Da boiz love it

[@windwalk8970]

No measurements just send it xD

[@maritasari3034]

Fwd instal to awd..

[@YostBuilt]

1st💪

[@alpacalaca]

This is sick. I want to do this to my integra. Def dropping a sub. But GODDAMN as a fabricator my head hurts. If that work holds up ill shit myself. you gotta grind the scale off that metal. black metal is not clean metal, thats just asking for cracked welds. The welder should sound like sizzling bacon, and yours sounded cold and probably too slow on the wire speed. but im just nit picking, once you go to school or take classes for the trade, i cant go anywhere without judging welds and shit lmao. i left a sub and cant wait to see how this ends up!

[@SuperLEEEDWARDS]

JEEZ NO TAPE MEASURE NO SPIRIT LEVEL NO STRING LINES AND SHIT WELDS, Why NOT take it to a body shop who WOULD LINE IT UP RUST PROOF BEFORE AND AFTER PROPERLY WELDING IN ALL THE BRACKETS. Here in the UK that would cost around £2-300 for proper SAFE fitment it’s GOING TO HAVE LOADS OF TORQUE RIPPING THAT OFF 2-3 runs guaranteed.