b series engine swap (step by step)

[@TheMapleDaily]

This video is actually amazing, I wish more people had this type of quality.. all the other videos are timelapses that explain nothing!!

[@reeewhydoihavetochangethese]

9:28 the absolute most important part

[@GuppyEgg]

Bro this video is 6y and still better and best information found on KZbin.

[@LethaboNkadimeng]

Super solid video very thorough especially with the diagrams shown for emphasis. This video deserves to have at least 2 million views by now.

[@bigdanish]

Nice vid good description for someone that has never done a swap 👍🏽

[@kaidokingz316]

thanks I appreciate it

[@BrinkTheG]

So iv been looking for a step by step video on youtube for weeks and finally found this, thank you so much iv learned alot of stuff that i would have never thought about and im about to swap on my prelude, thanks!

[@kaidokingz316]

+Savy K9 your welcome im glad it helped you

[@rozayek8068]

Great video! Thumbs up never done a swap but with this video I feel confident in attempting my first b series swap 👌🏽

[@DAAN_MUSIC]

Fuck me mate. I'm probably going to do my second swap based again of this video with now over 2 years in between. This step by step tutorial is just the best!! ❤🔥

[@dimitriliving]

Wow this video is timeless and so well made. Ty for doing this. I'm about 90% there and this helped me figure out the last few steps.

[@lozlogarage4924]

Thanks to your video took my 6hours to put engine in my car and boost it and street tune it

[@jordan7275]

I find it easier to do leave the grounds attached to the engine, just disconnect the one end from the chassis. And to drain all fluids after the shift linkage, and everything is disconnected besides pulling the axles (since you’d leak trans fluid) heater core hoses will always piss on the ground. I hate working with a wet floor haha

[@mightiestcarmods7954]

This video explained all what I needed for my 1st B16 Swap. Thank You !

[@kaidokingz316]

Sajaad Nazim your welcome I'm glad it helped you

[@slammed___dc4766]

Haven't done a swap before and trying to do one in the future helped out a ton!

[@kaidokingz316]

awesome I'm glad it helped you

[@coreymoto]

Call me late to the party I had no idea about the hoist back to lift the car instead of trying to tilt and get it out from the top I am just flabbergasted by that I only assumed you needed a car lift like in shops to do that. Holy crap🤷🏽‍♂️🤷🏽‍♂️🤷🏽‍♂️🤷🏽‍♂️🤦🏽‍♂️🤦🏽‍♂️🤦🏽‍♂️🤦🏽‍♂️🤦🏽‍♂️gonna make swaps so much easier now thank you

[@donnyhooks6970]

looking for a Eg hatchback shell for my B18c1 turbo that's in an ek as we speak :) Gonna take the weekend and swap both engines around. This should help a ton!

[@DENNISEATS]

Nice. Wish you show us how use the chain on motor when dropping

[@TenzaOnryoGaming]

Wow best step by step video. Subscribed

[@kaidokingz316]

TenzaOnryo Gaming thanks I appreciate it

[@AH-tx1nj]

I'm removing a b18a and installing a b18c5. thanks for the video. I know I'll use it.

[@kaidokingz316]

Allen Haynes your welcome I hope it helps you

[@meh6953]

Thank you for the informative video. This helped me understand my engine much more.

[@sopheaktras0424]

Awesome videos guys safety is what I recommend and step by step enjoyed the video and also man never seen anyone or thought of using a hoist to lift the car up that's safe and clever.

[@olderrol1968]

damn. I needed this video. Thank you guys very much

[@kaidokingz316]

you're welcome

[@ddjtycoon]

Thanks for the video man. Saved me money! Appreciate it

[@AndToTheRepublic4WhichItStands]

That b18c is solid gold now days lol

[@RicondaRacing]

12:07 Should show where to put the jack under the motor as to not crush the oil pan.

[@XxARM3DGAM3RxX]

The Punisher I think you can jack it up with a flat piece of wood

[@mightiestcarmods7954]

I think you support it with a jack until you loosen the lower mounts and get the chains on, then the jack comes out dolly goes in, loosen the upper mounts and land the motor onto it. Raise the Shell using tow hooks and Move it out of the way (since wheels are still in place). Then Bring the new Rolling shell and land it over the Motor using the engine crane, and follow the exact process in reverse order to swap. It is always good to sort the Interior looms and ECU wiring before mounting back the Motor (mainly for convenience, space wise). Correct me if I was wrong !

[@JamesDoylesGarage]

You know you real do a great job describing how to do it all. Every step. I kind of have the feeling you might be the best on You Tube when it come to swap tutorials. Is there a chance you have done anything with an F22A1 Honda motor? Thanks again for sharing your knowledge.

[@kaidokingz316]

James Doyle thanks a lot an no I mainly mess with b an d series but I plan on building a f22b dohc someday

[@stardocker]

no joke went step by step on a d series with this video and got it out

[@Salart123]

stardocker which engine if I may ask?

[@ksgod1929]

Arthur Salgado prolly d15

[@dohc22h]

You forgot to remove the music

[@SMGbird]

If it's a video where you're learning something that you're actually interested in, there will be some weird unknown techno music playing in the background. It's a requirement at this point...

[@gaston50952]

2000 Civic Si, 1.6L. B16A2 VTEC, my customer wants me to install a B18C2. Do I need different mounts, harnesses and ECU? Thanks in advance and great video.

[@kevincardenas5215]

Only thing different will be the ecu the harness will differ a bit since the gsr has the iab system & b16 does not but besides those things everything is the same

[@iavongsaesee8223]

Great video! I will be removing 97 usa motor and swapping it with 97 JDM gsr. Hope the results will be the same as yours!

[@hapkin2179]

Great vid gonna be helpful for my swap

[@loganward7800]

This should help swapping my b20z2 into my integra. Thanks

[@j.simpson1745]

Excellent, keep up the great work!

[@HenyTV_]

Great video. 10/10 💯

[@alangutierrez3531]

And to put it in is it just backwards?

[@MarcoMartinez-sz7ln]

Question important for me 1st time I got a 96 Acura automatic and I wanna replace the motor my question is do I have to remove the transmission too PLEASE HELP SOMEBORY I am not mechanic but I know One thing or 2I am not a bad SO PLEASE

[@libgapper9761]

Excellent video! Thank you

[@MrKiet76]

where to get the kit (harness/ecu/mounts) for this swap? Thx for sharing great job

[@sentree9857]

What's the most cost effective way to increase the performance of a b16a2 but keeping it NA? If I was to swap the block for a gsr one with type r pistons and cams, would that be what they call a poor man's type r? And would my tranny work?

[@kaidokingz316]

If your going for the cheapest go with a b20b block with your b16a2 head it be much faster than a poor man's type r

[@Ben28685]

I have a da9 integra and I want to swap my b20b in it what will be needed to do this swap please let me know because I would like to do it right and you guys look like your the best ones to ask please pass on this info to me thanks

[@therealsquadie4]

Ben28685 shouldn’t need much u can use the same trans as the ls and the same wire harness there’s a lot of videos out there for thisb

[@taraishot100]

Would love to see a 1.8 l bpt dohc turbo in to a 94 Mazda 323 familia protege love the GTX/Gt-r. They’re so rare these days

[@angelC916]

What would I need to go from a d16y7 to a b series engine on a 98 civic el. Any tips and advice will help thanks

[@marcialgarcia112]

Made it?

[@reza_dc2]

Great video ! where do we buy those chain lock loops your using ?

[@datkinee6674]

Nice vid… u could have left the header on n disconnect from bottom that will save a little time..👍👍

[@TheYetiownz]

Might be a dumb question but how did u get the harness connectors off that metal bracket? MIne are rusted in and will not budge at all

[@tiebei2548]

I know it's three years later but I will respond in case someone else needs it: You put a tiny flathead and lift up lightly and then shake it back and forth, ease it out. They are very hard, you have to wiggle it side to side with a lot of force. Make sure you have a firm grip on the connector so you don't pull the wires out. It was a major pain to figure that out, and they take the connectors off of the brackets because you will never get them off otherwise from what I can tell.

[@eduardosantos-kg8hf]

Did you use the integra harness

[@Streetflowautomotive]

Liked and subscribed ! Nice video

[@kaidokingz316]

Alan Lopez thanks I appreciate it

[@GreatBirdOfHope]

Can you do a video with 5th gen D16z6 removal?

[@kaidokingz316]

ertz mcgrackitz it's the same steps exactly just follow the video and you'll be fine

[@GreatBirdOfHope]

Ok thanks mines automatic:( changing over to stick plusB16

[@changalo263]

my bad, I didn't read in the description it was an Integra. I don't know shit bout those. im working on a crv. howd I end up here?

[@cali6998]

thank you so much learned alot

[@kaidokingz316]

your welcome

[@joeblow7388]

are you active in Hondas

[@EFNRND]

Remove the gas cap before pulling the fuel line

[@tiebei2548]

It will still spray a little bit but not like the video, keep the rag handy. Good tip.

[@garagejunkies2282]

My b20 on my ek hatch 97 is titled on the driver side I got yonaka solid mounts can someone help me

[@Fuzion180]

Top video!

[@bozgaming333]

What kind of steering wheel was that at the end?

[@dln.sweeney]

non-airbag JDM ITR

[@fluffy-_-bush]

awesome vid. I did my swap. thx I did like the vid and sub.

[@h23beltran24]

for a d series is the same thing??

[@kaidokingz316]

j. Beltran yea

[@YoungGearHeads]

Hey great video!

[@HaxNotice]

Absolute legends.

[@iWerli]

this is the video im using to pull my engine to rebuild it so thanks for the vid. also, why in gods name is everyone putting the b18c in a civic instead of just buying an integra? i know im biased because the 5 cars ive owned have been integras but still LOL

[@germanresendiz3778]

Teggies are Rare to find nowadays especially clean ones and stick shift ones

[@olFreddylo]

Why the ecu?

[@kaidokingz316]

Freddy Lopez what do you mean

[@robertappley809]

Freddy Lopez Gotta swap the ecu for the b series to run on. All the preset engine settings basicly lol.

[@mich7.3stroker24]

were u located?

[@kaidokingz316]

wichita ks

[@stevanbugarin303]

olathe ks here thanks for the video

[@kaidokingz316]

+Stevan Bugarin your welcome glad you enjoyed it

[@nobodyimportant_23]

Lol Nice music!

[@tyl3raz7]

Thank you a lot

[@angrycatowner]

This is the easy part. Now how to reinstall it?

[@kaidokingz316]

tough customer video channel installing it is actually easier cuz u know where everything is u took off pulling it out just remember the last step pulling it Is the 1st step installing it

[@dylanmounsey7515]

Do everything you just did but In reverse order homie

[@sessleandsharper]

Good vid

[@kaidokingz316]

thank you

[@marcorrre]

Most stupid way to take an engine out, the legs of the crane get in the way so you can't wheel it out. I needed to take off the intake manifold and distributor with the car in the air to get it out. Notice how they didn't show them getting it out from under the car?

[@javziovaldez3024]

Haha I too use a hammer anytime I am kissing a tool 👍

[@aaronfraser2347]

I found a full b18b swap for $1800, trans, axles, ecu, harness

[@changalo263]

personally,i think you took off a few things thatvwernt necessary.

[@xJDMWaRRi0Rx]

I'm doing my first swap tomorrow. What did he talk of that wasn't necessary to do?

[@SleptOnRacing]

What did you find out wasn’t needed lol

[@MoveMint.est85]

✨✨✨✨✨✨✨✨✨✨✨✨✨

[@MtGarage]

Love these swaps! We're working on swapping an H22 into my EK. If you're interested I have a playlist of the progress so far. kzbin.info/aero/PL1bewzles2ChESnrCzqNudF3I1bI-Z2Kg

[@davidbellerue5221]

My b20 was held in place by lockweld and a bologna sandwich

[@kingkevner1927]

2006 videos

[@deus2122]

Need to swap the o2 ?