Bandsaw Circle Cutting Jig Woodworking Jigs and Fixtures for Woodworkers Cut Circles with band saw.

Woodworking circle cutting jig on bandsaw band saw. Jigs and fixture for woodworking shops, circles on the bandsaw. Woodworkers, DIY, how-to, how to, hack, shop tricks, woodworking tricks.
Bench Dog Dual Track... www.rockler.com/bench-dogreg-...
Miter Track Mounting Track... www.woodcraft.com/products/13...
Laguna 1412 Bandsaw... amzn.to/3rZNzqW
Or shop my entire curated collection (Shop Tested) on The Thoughtful Woodworker Storefront…
www.amazon.com/shop/thethough...
As an Amazon Associate I earn commissions, and am grateful for your support.
Woodworking circle cutting jig for the bandsaw helps you cut perfect infinitely adjustable circles every time! Woodworkers everywhere are always looking for their next project. Unlock your skills with this slick circle cutting jig for the bandsaw. It's never been cleaner, faster or easier to make perfect plywood or hardwood circles. Plus, this jig features plastic laminate and T-Molding edges, so it will really take a beating in a shop setting, and keep on performing flawlessly. Follow along with Willie Sandry and learn a great way to make jigs and fixtures for the shop. This jig is accurate and makes repeatable circle cuts with ease.
#woodworking

[@thetankslapper]

Ive watch dozens, this is the brst deding and explanation. Im going to renake mine after seing his.

[@SilverBack.]

Excellent video with All the information needed. Thank you for sharing this

[@TheThoughtfulWoodworker]

Thanks Douglas!

[@Dovetail-Artisan]

Hands down the best video on KZbin when it comes to building a circle cutting jig. Thanks so much!!!!

[@TheThoughtfulWoodworker]

Wow, I appreciate the kind words. Thanks for checking out the video. Best to you.

[@RSmith-ld9ct]

Nicely done; both instructional wise and design wise.

[@TheThoughtfulWoodworker]

Thanks! Appreciate the feedback.

[@JoesWorkbench]

Best circle jig I've ever seen, wow nice work! Thanks for the inspiration, cheers from Australia :)

[@TheThoughtfulWoodworker]

Hey thanks for the message Joe. If you ever get a chance to build one, and you use many circles in your projects, it can be handy to have around the shop. Thanks again!

[@gordonshiloh4997]

i dont mean to be so offtopic but does any of you know of a tool to log back into an instagram account..? I was dumb lost my password. I would appreciate any assistance you can offer me.

[@rodrigoroger8168]

@Gordon Shiloh instablaster =)

[@gordonshiloh4997]

@Rodrigo Roger i really appreciate your reply. I found the site through google and Im in the hacking process atm. Seems to take a while so I will reply here later when my account password hopefully is recovered.

[@gordonshiloh4997]

@Rodrigo Roger it worked and I finally got access to my account again. I'm so happy! Thank you so much you really help me out !

[@genekatauskas6904]

It's Friday, I'm glad we're not trying to launch a Rocket 🔨

[@rexcowan4314]

So, why laminate and contact cement instead of PVA or pre-laminated stock? Seems like more cost IMHO. I appreciate your video and learned a couple of things. Thank you.

[@TheThoughtfulWoodworker]

Hi Rex, good question. I have used melamine for previous shop jigs and found it didn't hold up. The surface coating is very thin on some of these pre-laminated products. I prefer to use Wilsonart brand laminate and contact cement. Of course the jig will work fine without a laminated surface at all, but it makes for a nice durable jig. Take care. Thanks for commenting.

[@rsitch1]

Your circle cutting jig is excellent!!! Would you consider a adjustability screws between your magnets as to adjust for the different blade saw sizes? Bob

[@TheThoughtfulWoodworker]

Hi Bob, You could certainly try it. I'm not really sure what it would do other than limit the slot depth. Cutting accuracy would be the same. The one thing I might do different is to limit the length of the dado for the track. If you keep that dado 1/4" or more away from the blade slot, it would give you zero clearance cuts. Best

[@mailmusic]

Love this idea, however my track did not come with a T-track insert that you mounted the scale on. I think I'm just going to make a t-track filler out of wood (3 pieces and glue it together) and insert it and mount the ruler on that. About the only thing I can think of to do.

[@TheThoughtfulWoodworker]

Thanks Keith, That sounds like it might work. If not, you might have to order the combination track from Woodcraft. Powertec tape measure kits fit in that ok. Good luck!

[@douglasliterski8406]

What was the source for the steel washers that fit the 1/2" magnets? Great jig, love it.

[@TheThoughtfulWoodworker]

Hi Douglas, Thanks for the nice comment. The magnets are from Rockler. If you don't want to use the steel washers that hold the magnets in place, you could just epoxy magnets into drilled holes. Either would work fine. Best

[@rayjohnson4418]

When positioning the board to cut, how do you line up for that 8 in? And do you just hammer it down onto the jig? Thanks.

[@TheThoughtfulWoodworker]

These jigs can seem confusing until you build one. Once it's on front of you, it's all quite clear. Basically just drill a shallow hole on the bottom of your workpiece. Then loosen the sliding centerpoint with a screwdriver and position it as needed. Then just tighten the screw and cut the circle. Works great! Best

[@alfkey4155]

I wish I had the money to buy any of that stuff,,. I manage with a coronet imp bandsaw (1950-ish) and a 12-inch x 12-inch piece of old plywood with 6 peg holes,, but hey, don't feel sorry for me, I'm happy with my lot, I wouldn't have room in the garage anyway, I have a small lathe, the bandsaw, scroll saw and a grinder, and in the word of the song "who could ask for anything more",,. Regards Alf

[@TheThoughtfulWoodworker]

Well, a sharp new blade will make any bandsaw cut better. Keep a good blade on it and see if you can a few more years out of the saw.

[@alfkey4155]

@@TheThoughtfulWoodworker Thank you

[@vankicklighter9555]

I've been looking around for a good circle cutting jog. I really like your design. Can you give us the dimensions and distances you used for the miter bar and the combination t-slot?

[@TheThoughtfulWoodworker]

Hi Van, it's 18" square overall. Miter bar located 6-3/4" from left edge (as you use the jig). Center of T-track of combo track is 6-3/4" from back edge of the jig. Good luck

[@vankicklighter9555]

@@TheThoughtfulWoodworker Thanks so much. Looking forward to getting this jig completed and a couple of projects underway.

[@kevinrappold7795]

so.. just out of curiousity. Provided you have all of the materials and tools laying on your workbench, how long start to finish on something like this?

[@TheThoughtfulWoodworker]

Hi Kevin, You can build the circle cutting jig in a day. I used quick set epoxy to mount the track, so nothing really to hold you up. It's a tough little jig and should last a lifetime. Best

[@dawnbigwarfe6871]

Would this work if you wanted to cut angles on circles also

[@TheThoughtfulWoodworker]

I guess I'm not really sure what you mean by cutting angles on circles. Basically, the jig is just for cutting accurate circles. I suppose if you found a way to fix the rotation, you could use it for other purposes like cutting angles. Best of luck.

[@michaelroth5234]

Hi Great Video: Do you happen to have a plan or diagram you can share for the lugana 14BX that you made the sled for?

[@TheThoughtfulWoodworker]

I don't have plans for the 14BX, but in the comments section... I think second comment down, I list dimensions for the 1412 circle cutting jig. It should be very similar for the 14BX. Best of luck.

[@J1mRDavis]

Where can I get the threaded T-Track hardware that you used

[@TheThoughtfulWoodworker]

This blog may be helpful. The parts are available at Woodcraft or Rockler. They don't come threaded. Good luck! info.lagunatools.com/bandsaw-circle-cutting-jig

[@user-kg2gp2tz6f]

How do i get to the plans for this circle cutting jig?

[@TheThoughtfulWoodworker]

Hey Mike, you can find all the details for the circle cutting jig here.. info.lagunatools.com/bandsaw-circle-cutting-jig Thanks

[@user-kg2gp2tz6f]

Awsome! Thanks so much!​@@TheThoughtfulWoodworker

[@woodworking4459]

Do you offer these plans ?

[@TheThoughtfulWoodworker]

Here's a detailed blog on the jig... info.lagunatools.com/bandsaw-circle-cutting-jig Best to you

[@woodworking4459]

@@TheThoughtfulWoodworker hello, I have a question and maybe you can help me. I also bought laguna fusion 2 and I have Diablo blade 90th but I don't know if the riffing knife is suitable. The seller in Australia told me that they don't have thinner riffing knife and I noticed that the diablo blade is thinner than the standard laguna blade. Note: i wasn’t sure which tablesaw I should buy but, I bought the F2 because I watched your videos Thank you

[@TheThoughtfulWoodworker]

@@woodworking4459 The Fusion riving knife is 2.2mm thick. My Diablo Ultimate General Purpose blade has a 2.4mm kerf, so I think you're setup will be fine. Best to you.