This video shows how to remove needle bars, replace a needle bar driver, set needle depth and jump timing, and put it all back together.
Пікірлер: 27
@robertyoung-l7hКүн бұрын
Kirk, Thanks a bunch for posting this tutorial, i just replaced my driver and this helped immensely!
@archavator6 жыл бұрын
And also thank you Please keep making videos about barudan. A lot of people are happy to see these videos online
@kimpark51799 ай бұрын
Can u do a video on how to replace a needle bar stopper?
@SARmedic183 жыл бұрын
Thanks for this. After doing the replacement I am getting alternating d14 and d3 codes, any suggestions as to how to remedy?
@torreypovich8023 Жыл бұрын
What does the needle bar stopper do.. the plastic or rubber roller looking piece? Mine broke.. and now machine won’t always trim..
@kimpark51799 ай бұрын
My needle bar stopper broke too. Did u get any info on how to replace the rubber piece?
@carlosramos75813 жыл бұрын
Thank you for making this video. Make more please
@slickest1ofall5 жыл бұрын
Just What I was looking for. Thanks for the knowledge.
@Twisted_stitches_leather6 жыл бұрын
Thank you for making this video. Hope to see more.
@vjanand18194 жыл бұрын
Thanks for making this video ..as my machine showing D 10 error what's I have to do ? How to repair ?
@bruceadams7119 Жыл бұрын
Would like to see how to replace the res plastic caps part HT230190 Need bar addy. Barudan elite 2001. Bruce Adams
@europemovies16959 ай бұрын
Hi sir to solve board of the embroidery machine “Barudan” there is a two bottoms we have to click it together for settings of needles To change from 8 needles to 5 needles, l have to go to the settings. First, there are two buttons that must be pressed continuously. The first is the power button, and there is another button. Or two buttons I would like to contact with you if it possible I lost this way do you know it I can upload a video to my channel if I want more clarification to help me please Thank you.
@archavator6 жыл бұрын
Do you work for barudan because they are finally posting videos
@jessiegibson9023 Жыл бұрын
Thanks
@arnaldo6056 жыл бұрын
Can you do one on needle depth on newer models?
@aaronpalmer57822 жыл бұрын
I went through all the steps here in your video, but now, when it starts to run its like the driver isnt getting held out to stay in contact with the needle bars? there is good tension from the spring any ideas?
@kirkbrooks1012 жыл бұрын
If you pushed down to much on the pin that holds the needle bar in position, it may stick and not release, so maybe try readjusting it.
@aaronpalmer57822 жыл бұрын
@@kirkbrooks101 the needle driver works smoothly, i did have a pin tension issue it was a bent shim i replaced it with the ones Barudan sent me and it worked smoothly. ill have to look into again put a new spring in as well
@kirkbrooks1012 жыл бұрын
@@aaronpalmer5782 sometimes the needle bar driver just sucks, I keep a bunch on hand just in case one doesn't want to move freely.
@aaronpalmer57822 жыл бұрын
@@kirkbrooks101 yea i could see that since they went to the S style head alot more plastic in here for sure thabks for the help Sir. Hopeing to get down time in production to finish this
@shirtsillustrated86044 жыл бұрын
BIG Thank you!
@michaellissow5436 жыл бұрын
More videos please! Some on the BEXT 1501 CB II
@nancyl672 жыл бұрын
ARE you Barudan technician ?
@kirkbrooks1012 жыл бұрын
Used to be.
@nancyl672 жыл бұрын
@@kirkbrooks101 I just got single head 15 needles model BEVT, can you do training on the phone by facetime I can pay you , I in California thanks