The pictures on the thread were so unclear so I hesitated to do the mod... Thanks so much for making this video!
@michaelbirchall22476 жыл бұрын
This is a great video, just what I was looking for. I have just done this mod, but I didn't bother with modifying the pin part, I just did the resistor part and soldered a pin on the other end of the wire that I plugged in to the battery balancing port (third one giving 4.16v ish). Works perfectly!!! Thank you very much.
@djd-zl8bx8 жыл бұрын
I did this mod to the -ia6b rx and upgraded the fs-i6 tx firmware. All is working great! The rx SMD circuitry is really small. The series resistor (for voltage telemetry sensing) cracked during mod... had to replace with 39.2 K ohm resistor. Voltage reporting is very accurate. Great mod(s)! Thanks to all for the good ideas and firmware upgrade!
@georgie35 жыл бұрын
Great mod, I've done it many times. Always tricky, I do a simplified version by running the wire from the 38.4k resistor out a small hole in the case, strain relief with a spot of glue on the PCB. No other hacks needed. The tiny resistor always falls off on me, then I connect a 39k resistor externally. Note that you don't need this mod if you can set up iBus telemetry in iNav or Betaflight! You can enable iBus telemetry using the diode/resistor trick described in iNav documentation, or using Flit10 receiver. iBus telemetry parameter 2 is battery voltage from the flight controller by default (connect FC battery monitor pad to your battery V+). In your transmitter (I use FS-I6 with 10channel firmware mod) change "Int LiPo" to "Ext LiPo" in receiver battery settings.
@illusionistsam4 жыл бұрын
I want battery telemetry can you send me a link i really want to have that i dont have goggles and i crash alot in LOS battery monitoring is difficult for me i just have to check with external meter. Which distub my momentum
@martinr11042 жыл бұрын
Hi Georgie, I just read that you were using iNav telemetry with iBus and the XA6B receiver. Did you also use GPS with your FC? I'm trying to get the complete GPS-telemetry data but showing up on my transmitter is only temperature, course, status and current, so in principle there is a data transfer from the FC to the receiver to the transmitter. But what I'm missing is latitude, longitude, speed, alt etc.. Unfortunately there is nearly no information available and what is written in the iNav telemetry docs doesn't seem to work as described. Greetings from Germany, Martin
@dominikuskoch80335 жыл бұрын
Thx for sharing this - its awesome. I have only make one cut and use a jumper wire to the balancer (from the resistor). Now I am ready to fly.
@MicroRCFiend8 жыл бұрын
Slick workaround and finally a useful use for rx readout telemetry voltage. I always thought that was daft. I heard the C version does this function
@sptrader63166 жыл бұрын
The Flysky X6B receiver has battery telemetry built in, along with RSSI (great for tracking a lost model). It's smaller too but still has great range.
@BadBADdAd996 ай бұрын
Just made the cut and added the wire. Now I have a voltage telemetry I can use!! Thanks for making it easy!!
@Anton-sz6ef4 жыл бұрын
It's funny that I have a car that uses two li-ion batteries, in series they make around 7 volts so I can directly power the transmitter from there and read the voltage, no need for mod, then in parallel with the transmitter I have a voltage multiplier followed by the motor driver so it's perfect for me! I didn't know about this mod but I used this configuration to make it work. Thanks for the mod tho, very useful for future projects!
@xkitejunkie7 жыл бұрын
Thanks so much for this, just done mine at it worked perfectly. It's great with the modified firmware as it has settings for 3s, 4s etc. By the way in the modified firmware you can skip slowly scrolling through setting the alarm voltage alarms by pressing and holding the OK button in each alarm.
@simonbruce827 жыл бұрын
pwrkiter sounds like a great firmware update! Do you have a link to the download? Been annoying me that there's a 10V limit! Thanks in advance!
Just finished this mod and worked perfectly Thanks!
@christopherbiblis59717 жыл бұрын
i know it's an old video but i did this today and it worked perfectly. Cheers.
@hackedi.t30658 жыл бұрын
yes that was very interesting! I guess the 2 cell option you mentioned would work perfectly fine.
@DL7AFB7 жыл бұрын
Thanks for sharing your knowlegde. The modification works fine with my FS-IA6B / FS-I6S.
@TopoFPV8 жыл бұрын
very useful video !! I have done in my two receivers and works perfectly with the help of Flashed transmitter with the 10-channel version, that version can set the alarm battery voltage 3s to 6s, I recommend upgrade the version of the transmitter.
@iforce2d8 жыл бұрын
Yes, I tried that, video is processing now :)
@ashishpawar22613 жыл бұрын
it's working perfectly. Thanks for such informative video
@fpvkabo7 жыл бұрын
Don't need to go to all the trouble, just hook up vbat to power it, I've tested to 3S works great, when I get ready to blow one I'll test it at 4S, but for now, 3S shows 12.6v at my receiver! (of course it goes down as quad runs on)
@covinhas875 жыл бұрын
Great help. Very appreciate your macro pictures. :)
@Usr-O0OlOIIllIlIlIllIIl0O0o0oO8 жыл бұрын
Thanks for video, it's really helpful. By the way, in FSi6 10ch mod you can set up more than 10v max voltage, even you can set up battery type and cells count.
@neal42548 жыл бұрын
please help me out on as to how do you get to see more than 10 volts please would appreciate it
@iforce2d8 жыл бұрын
I think that part was in the transmitter firmware mod, not in the receiver. At least, I'm pretty sure I never showed it anywhere in this video...
@phildawe71728 жыл бұрын
this is good. I have this transmitter and receiver, I have been using my no telemetry turnigy 9xr more but i may have to try this mod as the sticks as so smooth on this transmitter. You can repair the receiver antennas cheap if you find an old wireless modem router, some of them have 2.4g external antennas. I bought one from an op shop. thanks for the vid dude
@iforce2d8 жыл бұрын
yeah, I have a few of these actually that would work ok, the tiny soldering looks quite tricky but I might give it a try sometime: goo.gl/WsILxW
@phildawe71728 жыл бұрын
+iforce2d gotta like bangood. it seems like ibus sounds about as fast as sbus. and your other vid on updating the firmware is excellent. fingers crossed i can get it to work even for the voltage alarm alone
@ismzaxxon8 жыл бұрын
I just stumbled onto this channel. If you set up a fesistor network of ...say.... two 1K resistors, one end to ground and the other end on your battery, in the middle of your two resistors you will get a reading of half of your battery voltage. so a 12volt battery would give you 6 volts on your alarm setting.
@ismzaxxon8 жыл бұрын
fesistor=resistor.
@iforce2d8 жыл бұрын
aww.... but fesistors sound more fun :)
@roidroid8 жыл бұрын
yeah that's what i was thinking too. Use a simple voltage divider, so that the 14.0 - 16.8V 4S battery will power the receiver with 5.41 - 6.5V, then set your alarms accordingly. It'll work for 4S and 3S without any hardware changes, as the output voltage for 3S will be 4.06 - 4.875V. the FlySky ia6b receiver needs 4.0V~6.5V, so all of these figures are within that range.
@iforce2d8 жыл бұрын
yes, I did mention that at one point in the video, but I was planning to do the firmware update anyway which would solve the issue
@phildawe71728 жыл бұрын
finally tried this and it works, awesome mod vid. there must be a similar option for the non 'b' receiver too as it also downlinks the rx voltage. there is the same bank of 2 resistors... hmm :)
@phildawe71728 жыл бұрын
ah its on rc groups, cool.
@srul768 жыл бұрын
Great video. i gave a test yestorday done the mod and it working perfect thanks...
@RCFlyer858 жыл бұрын
Just to throw it out there... If you get the new ia6c receiver it will automatically add external voltage to your transmitter
@mikegatlin1ify8 жыл бұрын
RC Flyer85 having issues with it reading 0.00v and setting my alarm off! any way to fix that you know of?
@RCFlyer858 жыл бұрын
No I haven't experienced that. We are talking ia6c correct? You have it connected directly to the battery?
@mikegatlin1ify8 жыл бұрын
Nope, just got it connected to iBus (vcc, gnd, and signal to sbus) the transmitter connects fine and she flies...but now it just beeps and shows low Rx voltage, I've messed around with some settings and can't seem to figure it out
@RCFlyer858 жыл бұрын
Are you saying your not using the B-Det plug but have vcc going in on your 1 ibus plug? A picture would be better if you could post 1 in the RCGroups forum here www.rcgroups.com/forums/showthread.php?t=2734291
@thelongranger556 жыл бұрын
RCFlyer85 I know this video is old , but can’t one just wire this receiver directly to the flight battery so you can power the receiver still like normal without doing all this work ? , or is that just not a safe way to wire the rx ? Dose the rx need to have a steady and constant voltage and is that reason we are using a dedicated pin in the middle of the bind pins ?
@rbmwiv5 жыл бұрын
Pretty neat. I will stick with my runcan 2 it has osd with voltage and I can hear my buzzer with the headphones.
@stevebarrett85443 жыл бұрын
Well done mate great video
@davidalston17426 жыл бұрын
Thank you for showing the modification. How do you now bind the receiver after disabling the supply line in the bind slot. Suggestion:-Would it not be easier and less destructive to remove the series resistor rather than cut up the board. Use the resistor pad to place the wire and run it out directly Dave
@iforce2d6 жыл бұрын
Binding just connects the signal pin to ground, it does not require a 'supply'. I'm not totally sure but I would expect that resistor is part of a voltage divider, as well as obviously limiting the current flow, and it might even be connected to other things too. I doubt it could simply be removed, you would need to at least solder an equivalent resistor in series with the wire coming from vbat. Overall I think removing the resistor would be more destructive because you risk damaging the pads on the PCB, and soldering it back in would be a pain in the ass so it's not really easier either.... In contrast the middle row of exterior pins are all connected in a common rail so even after cutting the trace you still have another six identical pins to use.
@iforce2d6 жыл бұрын
Overall though, this mod is not very convenient. I only did it once and since then I just use the voltage sensor module for ibus, the FS-CVT01. It costs about $4 and isn't too big or heavy.
@magneresjuan2 жыл бұрын
Hello ! Great vid. I conect oposite voltage baterry to my fs ia6 receiver AND saw smoke... any ideas for the repair?
@redalin-nz8 жыл бұрын
Great video, i've been wanting to do this for a while but couldn't find the right instructions. I usually depin and decase my ia6b receivers, so I can just cut the traces on the resistor and run a wire directly yeah? no need to worry about that pin. And yes with the modded firmware you get quite a different Rx Battery menu
@iforce2d8 жыл бұрын
Yes, that would be right.
@keithmason16137 жыл бұрын
Hi Matewouldn't you be better off buying on of these Turnigy TGY-CVT01 Voltage Sensors and be don with. Rather then the cutting and soldering? Just my thoughts. If there's a reason why you chose not to buy voltage sensor please do let me know. By the way I enjoy all your videos which I find very informative. Well Done.
@kobrapromotions7 жыл бұрын
Thats adding an extra 11g but
@iforce2d6 жыл бұрын
Actually these days that's what I do. This mod is not as convenient as just paying $4 and using the FS-CVT01 sensor module for ibus.
@MuRaT_C Жыл бұрын
Great Hack, thank you for sharing. One question... works this hack also for the iA10B? is pretty much the same Receiver but with 10 Channels instead of 6... Thanks!
@joaocastelo72517 жыл бұрын
Will this create any problems with future bindings ? PPM and Ibus work good ? Great vid thanks!
@iforce2d7 жыл бұрын
No problems that I know of. I don't see why it would be a problem.
@chrisleech15658 жыл бұрын
The Tx/Rx package at ~$65 USD @ BG is a good value. But the 9XR Pro is the same cash outlay and may use OpenTX , or ER9X both of which are still being improved and upgraded. It has Haptic, Voice, and SDCard to store FW and Model mixes. And with a FrSky DHT 2,4Ghz Telemetry capable Tx module (for instance), one may have any variable you can send via soft serial, or UART from your FC or Smartport, be it Mavlink or what.... But who is looking at the screen of their Tx during FPV anyway :-)
@AliGreenFPV8 жыл бұрын
I did not quite understand where the ground from the battery goes, can you please explain? Dose the ground that comes from the 4s battery can be solder with the ground that comes from the FC to power the RX (5v and Gnd)?
@pigvador93957 жыл бұрын
very interesting job. Thank you!
@TheMadmacs7 жыл бұрын
just revisited this vid to get the beeper going again... i smashed my voltage alarm beeper, so i'll need to use this attery warning even though its too quiet .... where would we be without these vids?..... on the ground... ps i also did the 10channel mod... works beautifully. i'm amazed i managed the solder job....
@MrGivmedew8 жыл бұрын
why all the work to get that wire onto that pin when you could leave that pin alone and just cut the other traces and have the wire just come out on its own. it seems safer that way you would never accidentally plug it into one of those 5v pins.
@BLINKFEED7 жыл бұрын
i recently bought fly sky FS-i6. but the problem that i am facing is the it is not getting bound by the receiver which is FS-iA6. i tried all types of binding. still it is not binding. can you help me with this
@sp8rk8 жыл бұрын
Hi i've done the mod on two receivers but it doesn't give back any voltage i just get a empty RX on my I6 and on my I10 just a ? mark on the battery icon :/ any ideas??
@gordondrummond20338 жыл бұрын
good work mate :) I'll share this video to my friends.. a lot if them have the i6 as well... oh and do you know what the errors means on this tx? I get them with most of my quads! like 1% up to 15%
@iforce2d8 жыл бұрын
I think it's like a reverse RSSI indicator, just tells you what percentage of packets that were sent did not make it to the receiver and back.
@R4W20N36 жыл бұрын
Hi there! Is it possible to operate the IA6B receiver with a 2s Lipo pack? Im kinda struggling with finding a suitable Battery, because the voltage limits printed on the case (4V-6.5V) seem too high for 1S LiPo (like, 3.2V-4.2V) or too low for a 2S-Pack (6.4V-8.4V). Thanks in advance!
@iforce2d6 жыл бұрын
No, it's made for 6v max. What problem are you trying to solve exactly? I have tested these radios and got 13 hours from a set of 1500mAh rechargeable NiMH batteries. They are much more convenient than a lipo because you don't need to worry about returning them to storage charge if you won't be using the radio for a while, also very easy to keep a set of normal dry cells in the car or whatever in case you need them. If you are simply following the trend of changing to a lipo, I would suggest not to bother. Just get some rechargeable AAs and a wall-socket charger.
@CorkKNIFE7 жыл бұрын
Is adding the other telemetry sensors (like altitude TGY-CAT01) more straightforward? I can't find a single video or review on the altitude sensor TGY-CAT01.
@iforce2d7 жыл бұрын
Yes, much more straightforward - you just plug them in :)
@TheUnnamedGent8 жыл бұрын
I cut the traces and now the bind port middle pin has continuity with the ground pin. Surely this can't be right, right?
@iforce2d8 жыл бұрын
That's definitely not right...
@stevefox37636 жыл бұрын
did you do the tx firmware? its a whole new world when you do that, the fs-i6 becomes a 10 ch full feature unit that competes with much more expensive units! im running a version that also gives me rssi and a load of other telemetry on my tx display plus you can set 3 separate alarms for say low rssi or any other telem function you want .
@iforce2d6 жыл бұрын
kzbin.info/www/bejne/m5LNYYBoZp17ia8
@stevefox37636 жыл бұрын
iforce2d ahhhh, yep lol. I've tried so many different versions, some have been unstable and a huge number have collective pitch broken in the variable pitch Heli menu eventually I found a version that was fully featured, stable and allowed me to use that menu, it's fine if your flying a flybarred Heli, use the 120 swash and the mixing is all done in the tx but if you want to run a flybarless controller your stuffed without the independent channel output of the other menu as the FBS controller cannot use an already mixed input! But this is all part of out hobby, working out problems and modding stuff gives satisfaction when you succeed.
@samocooper90708 жыл бұрын
Hey Chris I'm about to do this mod, can you tell me how you removed the black plastic on the headers? bent my screwdriver trying to lever it off
@iforce2d8 жыл бұрын
I used a screwdriver, start from the ends and take turns prying each end a tiny bit, go real slow
@samocooper90708 жыл бұрын
Thanks for that! just did it, works great! this is an amazing controller/RX combo for the price! any video for lipo conversion? also any other things we can add to telemetry?
@davidemele28425 жыл бұрын
It worked, but I cutted only between the resistence and then I pulled out the cable for the battery sensing. It's strange the fact that the voltage meter and power supply are together.
@shawng57996 жыл бұрын
I am a newbie to the hobby BUT what if you powered the RX from just one cell via the battery balance plug?
@iforce2d6 жыл бұрын
Sounds a bit risky. Usually the innards of the receiver run at 3.3v and it will have a step-down regulator to change the 5v input to 3.3v. Step-down regulators usually 'drop' about 1 volt internally, so to provide 3.3v it would require 4.3v input. Often a 3.3v device can still run at about 3v, so a 4v input might be enough. A fully charged lipo would be 4.2v, but then as it discharges while flying....
@shawng57996 жыл бұрын
Then I thought what about people with a 1S model they will be seeing what I think I can replicate. Set the warnings at 3.2,3.5,4.2 I know it says 4v-8.4v but the 1cell would only be 0.8 below that at worst. I am building a GPS bird so I could try this and the worst that would happen is it would return to home.
@iforce2d6 жыл бұрын
No, the 1 cell will discharge down to about 3.5v or whatever you let it while flying. It will only be above 4v for a very short time. Pretty much as soon as you throttle up the voltage will go below 4v.
@shawng57996 жыл бұрын
I carried out an experiment today and it seemed to work! I took the props off my Bugs3 and plugged the RX into the bugs battery balance plug. I ran it for half an hour and then got bored. Because there was no load it was taking forever. I measured the end voltage as 3.78 per cell. I had hoped that both transmitters would go into low battery mode together. My next experiment will be to fasten the RX underneath my Bugs and take it out for an actual flight using the two transmitters. I did try to load the motors by putting my sleeve over my hand and trying to grasp them but it got too hot. But the experiment wasn't a bust and it will only take me 10 minutes in the field to see what happens. I'm an old retired engineer and seeing this problem for the first time,it just seemed natural to try. Will let you know how I get on either way but it won't be tomorrow my wife is putting a new roof on my garage. ;)
@iforce2d6 жыл бұрын
If you are going to keep up this kind of nerdy pursuit you could probably use a little variable voltage 'bench power supply', that way you could just dial down the voltage to pretty quickly see where it starts to brown out :) kzbin.info/www/bejne/jWbKm6WnlJ6nldU
@axelmunsch59358 жыл бұрын
hello, thanks for the video, I think I have burn the resistor during soldering and I would like to change it, any idea for its resisting value ?
@peterrottenhoffer95357 жыл бұрын
ME TOO, HELP
@IIIDarkWorlDIII4 жыл бұрын
Just desolder it carefully and measure it with a Multimeter. Search on KZbin how to desolder SMD resistors
@mom0g15 жыл бұрын
this work on 5s ?
@mom0g15 жыл бұрын
how bout 5s?
@toddbeal43737 жыл бұрын
the 10 channel upgrade changes all the battery stuff, so u won't have to run that resistor for 4s
@peterwoo24898 жыл бұрын
Can you also do a video on using IBUS on Clean/Betaflight? I want to do it but there aren't clear instructions/videos that I can follow... This radio has all the functions of really expensive radios!
@iforce2d8 жыл бұрын
I'm not sure if that's worth a video... I was actually intending to, but when I looked at how it's done, it's all over in less than a minute or so. In the cleanflight configurator (ports tab) enable Serial RX for port 2. In the configuration tab under Receiver mode select RX_SERIAL and in Serial Receiver Provider choose IBUS. Connect the ibus signal pin of your receiver to RC input pin 4. More details (but admittedly incomplete) here: github.com/cleanflight/cleanflight/blob/master/docs/Rx.md
@darven8 жыл бұрын
i use iBus for the ia6b - i need too because i am stuck with the NovaX firmware since i messed up my input order before flashing. the iBus is simple, its just a Serial Transmit at 115200 baud. you need to connect it to the Spectrum Sattelite input pin and enable it in the firmware. i have even written a Arduino Leonardo to read it and emulate a joystick at my computer. FPVFreerider friendly! :)
@mikadire13788 жыл бұрын
Just built my first quad so very new to this and had a couple of questions. How do you connect the battery to the receiver and what influence does the 'high' value on the transmitter have?
@iforce2d8 жыл бұрын
Usually the receiver and the flight controller both run at 5v, so you would connect the receiver to the flight controller. The flight controller will need a 5v power source, usually this is done with a BEC. Most power distribution boards often have a 5v BEC on them.
@mikadire13788 жыл бұрын
***** sorry probably wasn't clear enough. What I meant was how do I connect the battery directly to the pin that you separated from the rest, so that the receiver can detect the battery voltage. I might be really confused hear and this may not make any sense to you, in which case don't worry! thanks.
@iforce2d8 жыл бұрын
You'll have to make up some kind of connection yourself I think. I usually cut a little of the silicon shielding off the wire coming from the battery and solder into there.
@mikadire13788 жыл бұрын
ok, thanks!
@LAFFRS5 жыл бұрын
or just buy a flysky voltage telemetry sensor for £4 and plug it into reciever
@Enderkruemel4 жыл бұрын
If you dont have the space for it, this is better. Also this resiver is very big.
@DLM5173 жыл бұрын
Easier said than done on soldering!
@jellenijhof79737 жыл бұрын
is it not possible to use the balance plug of your battery and put it in the receiver??
@rokasnavickas34477 жыл бұрын
Hello collegue. I was wondering if there is a possibility to use my receiver as battery monitor in my apm aswell? Or is there only alarm on transmitter? Hope you reply me soon. Good luck mate
@iforce2d7 жыл бұрын
I don't know anything about APM. I think they have forums though, you could try asking there.
@rokasnavickas34477 жыл бұрын
I mean, the thing i was asking for, is there a possibility to monitor the voltage staight from receiver instead of ppm board?
@iforce2d7 жыл бұрын
"voltage straight from receiver"? This will always be 5v won't it? I don't understand what "ppm board" is...
so how I understand,, this transmitter has low voltage alarm, when your battery drops on critical level, i am newbie and i am building mine first quad, so that knowledge would be important for me
@simonsutherland8143 ай бұрын
Excellent 👍🏻 Cheers
@daleyoung877 жыл бұрын
Hello!! In Timbutus hack, it seemed that he eliminated the power to the #1 channel and had to re-route a supply for it. It looks as though you only took the power from the bind plug. Is this correct? So does this end the need to wire anything else?
@iforce2d7 жыл бұрын
I'm not "taking power" from the bind plug row, I'm using that pin to input the main battery voltage. So it needs to be disconnected from the rest of that rail because the other pins will be around 5V and the main battery will be much more.
@daleyoung877 жыл бұрын
Oh yes,... Sorry. I meant eliminating power from the #1 row. So it is a little different from Timbutus approach. Correct? You are eliminating the 5v supply to the bind row instead of the #1 row? Looks like your blue wire connects the mid bind pin to the resister on the other side. Correct?
@daleyoung877 жыл бұрын
I have the i10 reciever with the telemetry module, but the voltage reading fluctuates so much that it immediatly sets off the alarm when I throttle up.
@iforce2d7 жыл бұрын
Yes, the 5V pins for channels 1-6 remain unchanged. No idea what a timbutus is sorry.
@daleyoung877 жыл бұрын
Gotcha! OOPS Tributu (the guy whos video that you referenced in your video) Thank you so much!! Im getting ready to do this tonight. Have you seen your voltage fluctuate enough to set off your alarm?
@user-yk1cw8im4h8 жыл бұрын
What does the battery-powered power supply called ?
@iforce2d8 жыл бұрын
kzbin.info/www/bejne/jWbKm6WnlJ6nldU
@johnkodolemos24498 жыл бұрын
great vid man! one question is there a way to hack the beeper to ring when signal loss rises?
@iforce2d8 жыл бұрын
Not that I know of. But there is more work going on with the tx firmware, it might be possible in the future.
@johnkodolemos24498 жыл бұрын
that would be ideal! 40 bucks and you have everything!
@RealWorldAviationandGaming93928 жыл бұрын
Hello mate...I do believe if you do the 10channel mod ver 1-1 thru 1-5, that should take care of the telemetry displaying without cutting anything for the battery alarm to work.... it seems to be working for me.
@iforce2d8 жыл бұрын
The battery alarm I want is for the main flight battery. How can I connect that (16.8V) directly into the receiver?
@andianiszafirahandimadzwan45768 жыл бұрын
i already cut the trace, but seems i dont have any respon voltage reading from the rx.. should it be connected well? what i have done is, i cut the trace, connect my esc to the rx(which got the bec) then connect the +ve wire on ch1 to the first cell port. but then still no signal am i doin it wrong? or, can i do this just to see either im doing it right. 1.i cut the trace 2.i connect my esc (bec) to power the rx 3.i connect the +ve pin on ch1 to first cell on battery will i get the data? i do it at fsia6 rx btw
@iforce2d8 жыл бұрын
I don't know how it's done for the ia6, but if you take a look at the link in the description (if I had a dime for every time I've said that....) you will find that the original thread on rcgroups is all about doing this mod on the ia6.
@brightontilifly8 жыл бұрын
look at you already on BLhelli_s I know I nag you all the time but please let me know are you interested in coming on the podcast "let's drone out? I'd love to have you on!
@iforce2d8 жыл бұрын
I'm not very good at that kind of thing I'm afraid
@iforce2d8 жыл бұрын
Actually these ESCs are not BLhelli_s (I had to look up what that meant heheh) they are XM30A
@muh1h18 жыл бұрын
but they have the BLHelo Software on them :)
@iforce2d8 жыл бұрын
sounds like you need to look it up too :) Notice the _s on the end
@muh1h18 жыл бұрын
***** Oh wow, i think i have not been right correcting you in the last month even once :D I think i should stop trying and accept the fact that you know way more about quads than i do :)
@LJT93935 жыл бұрын
My Mobula7 FlySky version has some sort of telemetry that I can’t seem to figure out. Some stick inputs work and I get the beep that it does when it is Input proper, some don’t work at all. Now what I did find out, is that currently I have my RX battery displayed on my screen as yours is. I have the i6X version TX. If I do the save input on the sticks, so throttle Low; Yaw Low; Pitch Low; Roll Low. I will get a beep as if it were to save my current trims and calibrations. If I hold it tho for like a fraction of a second it actually removes the RC battery display on my TX. Does anyone know if the FlySky telemetry inputs are different than say Frsky?
@yusuftasdemir67224 жыл бұрын
is it same step for FSIA10B receiver
@kyriakosnikolaidis62497 жыл бұрын
can we put long range system on this transmitter? if yes please show me one link
@reezlaw8 жыл бұрын
OT, I know, but I'm really surprised at your accent turning rhotic at times... like when you say "here"
@ashaysave44148 жыл бұрын
can we connect battery and bec both to receiver?
@robmckennie42035 жыл бұрын
it seems like the receiver is being powered by a bec, but the value being fed to the sensor is coming directly from the battery
@nicolausadinugroho11338 жыл бұрын
after i did this modification, my Tx/Rx range only 1km maximum.... did you feel this mod reduce the TX / RX range...?
@iforce2d8 жыл бұрын
What was the range before ?
@nicolausadinugroho11338 жыл бұрын
Before the mod , i never fly more than 700 m ... (i worried about my batt capacity) ... But after mod , i try to fly as far as possible . And get High Error Rate ( 70-100 % ) at 1,100 meters .. more than that .. the signal indicator is blank ... i see some FS - i6 review ... there can more than 2 km .. but it is impossible for me ...
@41Extremo8 жыл бұрын
The 2km would be the absolute most, if you had a perfect set up with your receiver and were in an environment with no interference on 2.4Ghz. There are various videos online showing how to position your antennas to get more range, your best option is to watch some of them
@serbiakursula5 жыл бұрын
I've done everything as it mentioned in this video, but unfortunately, I've accidentally rip the right resistor :(. Does anybody know what was the resistance of that resistor? Thanks.
@schummiehugo5 жыл бұрын
bay a lipo volt meter split in a Y ( man women ).. rap it in your drone. en suc6 !
@serbiakursula3 жыл бұрын
@Castle of Glass oh...it was long time ago. I'm not sure...please, try here www.rcgroups.com/forums/showthread.php?2402288-FlySky-Turnigy-iA6-%28and-iA6B%29-voltage-telemetry-mod
@brakesitr7 жыл бұрын
Mine quit when I did a factor reset with the firmware update (cause I messed with the RX battery in the TX flysky.) and I'm using a FS-iA6B receiver... Don't mess with the RX battery settings!
@larsmartintangen70728 жыл бұрын
There is a beta firmware that support 4s battery and it also give you 10channels in ppm
@iforce2d8 жыл бұрын
I think you mean 10 channels in ibus right? kzbin.info/www/bejne/m5LNYYBoZp17ia8
@larsmartintangen70728 жыл бұрын
iforce2d you also get it in ppm but not pwm ofcourse, i set my up yesterday in ppm on a sp f3 board and it went really nice, in betaflight its great to have more then 6ch as i use channels to start/stop blackbox and on/off airmode on top of the normal mode switch and arming switch Tomorrow i will try to set up the battery monitoring telemetry, thanks for this video on how to do it 👍
@iforce2d8 жыл бұрын
Maybe we are using a different firmware mod. If you look at the video I linked to (at about 26:26), you can see on the scope that ppm still has only 6 channels.
@mrk3ma17 жыл бұрын
after all of it ,how did you connect yellow cable to lipo battery? through PDB?
@iforce2d7 жыл бұрын
Yes
@timberce7 жыл бұрын
Anyway you can take a screenshot of the connection to the PDB?
@iforce2d7 жыл бұрын
Connect it to any + point on the PDB.
@timberce7 жыл бұрын
Thanks a lot for your quick reply. Still new and curious if that will work fine for a 4s build? I saw on the forum that most talked about using a resistor wired directly to the battery? Subbed and recommended to friends. Awesome channel.
@iforce2d7 жыл бұрын
Yes, I used it for 4S. These days I just use a ready-made voltage sensor though, this mod was a real hassle and I don't think I will be doing it again. Sensor is about $4 goo.gl/PoFKM8
@SladkaPritomnost7 жыл бұрын
What's the point of monitoring regulated voltage?
@iforce2d7 жыл бұрын
Read the video description.................
@SladkaPritomnost7 жыл бұрын
ok thanks :)
@kabelloseskabel70295 жыл бұрын
Is it possible to send data from an Arduino via i-bus?
@iforce2d5 жыл бұрын
Should be, looks like somebody has figured out the protocol: forum.arduino.cc/index.php?topic=548520.0
@kabelloseskabel70295 жыл бұрын
iforce2d Thank you! It is not common to get an answer from a youtuber with that much subs.
@thmls57448 жыл бұрын
How did you cut with what kind of tool
@iforce2d8 жыл бұрын
a very sharp knife. craft knife, or box-cutter most people seem to call them
@mlc3ifly8 жыл бұрын
Does this mod need done with version 2 rx? Ia6b
@iforce2d8 жыл бұрын
I didn't know there was a version 2
@arabstar508 жыл бұрын
?can i use 3S 11.1v battery direct with FS-iA6B receiver
@iforce2d8 жыл бұрын
No. Read the label on the ia6b. It says 4.0 - 6.5v.
@jc_fpv_ec4 жыл бұрын
function for 4s battery ???
@brianevans45 жыл бұрын
Thanks
@v8consumption5 жыл бұрын
Can you do this with a8 receiver the micro one
@iforce2d5 жыл бұрын
No
@joshuachipps8538 жыл бұрын
How do I do this with out cutting anything?
@iforce2d8 жыл бұрын
You don't. Why would I bother cutting anything if I didn't need to?
@peterzingler62214 жыл бұрын
That all isn't needed. Just isolate the pin of channel 1 from the 5v rail and that's it
@leoluis276 жыл бұрын
nice video but 2018, vbats, OSD and active buzzers, 1 minute fix and you good to go
@ipuunx8 жыл бұрын
what max volt can do?
@iforce2d8 жыл бұрын
I tried it up to 4S ok.
@zerdoc20648 жыл бұрын
update your transmitter and then you can go a lot higher on the High settings.
@werdem8 жыл бұрын
what is better radiolink at9 or flysky i6? thanks
@iforce2d8 жыл бұрын
The flysky is the only one of those I have used, I woudn't know.
@kmitchel467258 жыл бұрын
That right angle PCB for the pins needs to be completely removed.
@iforce2d8 жыл бұрын
.... in order to do what?
@kmitchel467258 жыл бұрын
+iforce2d To make it cleaner/lighter...using Ibus most of those pins will do nothing...just solder direct.
@kmitchel467258 жыл бұрын
+iforce2d I kind of find it fugly...
@lloydprunier44158 жыл бұрын
Now I have a headache ! LOL
@zerdoc20648 жыл бұрын
for your alarm setting
@armortk8 жыл бұрын
+ лайк
@neclovek8 жыл бұрын
For better low voltage alarm install this firmware on your TX: github.com/benb0jangles/FlySky-i6-Mod-/tree/master/10ch%20Mod%20i6%20Updater/10ch_MOD_i6_Programmer_V1_5
@iforce2d8 жыл бұрын
yes, as I mentioned in the video, I will try that
@neclovek8 жыл бұрын
+ It also delays the annoying beeping when you dont move any controlls so instead of beeping after a minute, it beeps after 10 minutes i think. And i have a question: Is the isolation of that pin needed? Or can i just connect stuff to the little wire and leave the pin as it is without cutting it ?
@iforce2d8 жыл бұрын
Yeah the modded firmware would be worth it just to shut up that beeping :) If you were to extend that little wire to come right out of the case then no, you wouldn't need to do anything with the 5V pin trace. It's just that it's very convenient to be able to plug something into one of the existing pins. Gotta be real careful I get the right one now though :)
@neclovek8 жыл бұрын
Last question: I use a hi-volt lipo, do you think the RX will be able to handle 17,4V at input? I only have one RX and i dont want to risk it until i know it wouldnt fry it :)
@iforce2d8 жыл бұрын
I don't know, and don't have a good reason to try since I don't have any of those myself - give it a shot :)
@tetradb_8 жыл бұрын
There's a voltage sensor you can get for about $3 (hobbyking.co.uk/hobbyking/store/__76687__Turnigy_TGY_CVT01_Voltage_Sensor_EU_Warehouse_.html) I use one with my equivelent Turnigy radio and reciever and I monitor my 8S setup.
@iforce2d8 жыл бұрын
Yes, for a bigger quad I might do that. For a little one though there is enough crammed in there already.
@lilgreencanoe2936Ай бұрын
Hell no
@magneresjuan2 жыл бұрын
Hello ! Great vid. I conect oposite voltage baterry to my fs ia6 receiver AND saw smoke... any ideas for the repair
@bioodynine52496 жыл бұрын
Is it possible to send coordinates to the flysky fs-i6?
@iforce2d6 жыл бұрын
nope
@satishy86847 жыл бұрын
how to modify a ia10b receiver for voltage telemetry??