For Mobility Strategy Guidelines, please check out the complete playlist below :) 🌐Mobility Strategy Guidelines 💡kzbin.info/aero/PL4OXTttOk9WiYBSisxouxMiHY6ljkO_mA
@danserbescu13632 жыл бұрын
Ali, thanks, again such a wonderful presentation. For beginners, all the parameters for connected mode are received by UE in RRC Connection reconfiguration messages. There you will see measobjid (for which frequency there needs to be measurements) then reportconfigid ( what type of event is to be measured and for which measurement type like rsrp/rsrq and reported with its threshold, offset, hysteresis, time to trigger, report periodicity etc) and also measid ( measurement report id that matches a specific measobjid and a specific reportconfigid). Then when you will see a measurement report ID =5 for example you will know for sure to which frequency belongs that report ( from measobjid of that measurement id=5 for example EARFCN 3050) and what event was reported and for which PCI ( inside the measurement report there is the PCI of the neighbor cell that triggered the event for example event A5 for PCI 389). What Ali forgot to mention is that those days UEs are hardly staying in idle mode, most of the time are in connected mode. So mobility in connected mode is more important than mobility in idle mode.
@OurTechPlanet2 жыл бұрын
Thanks for always adding value to the forum :)
@liton312 жыл бұрын
Super simplification! Just loved it! Examples starts from 10:06
@OurTechPlanet2 жыл бұрын
Thanks a lot 😊
@coolmunzir2 жыл бұрын
Surely this comparison to avoid ping pong within Idle/Connected Mode & between Idle and Connected mode will help a lot... Thanks for the detailed video!!!
@OurTechPlanet2 жыл бұрын
You're welcome!
@iulhaq12 жыл бұрын
Excellent Ali ... one of the best I have gone through ...
@OurTechPlanet2 жыл бұрын
Glad to hear this! Thank you so much :)
@boonlengong1939 Жыл бұрын
Fantastic explanation. Always love your video 👍
@OurTechPlanet Жыл бұрын
So nice of you. Thanks!
@coolmunzir Жыл бұрын
can you share a short session over Cell Radius change regarding to Handover Success / Failure
@OurTechPlanet Жыл бұрын
Sure, will create one soon
@babisg976 Жыл бұрын
Nice and clear! Thanks
@OurTechPlanet Жыл бұрын
You are welcome!
@MrYoyokdp2 жыл бұрын
Thanks Ali wonderful, I think you should say -104 is higher than -106 instead of lower, but that's just fine you have revised on irat part :)
@OurTechPlanet2 жыл бұрын
Thanks Yoyok :)
@HarpreetGujral272 жыл бұрын
Nice , Thanks once again ! If we set the inter freq measurement based on Event A3, then for connected mode HO will these A5 thresholds play any role or ignored?
@OurTechPlanet2 жыл бұрын
If you IFHO event set as A3 then there is no role of A5.
@subratdas89362 жыл бұрын
Hi Ali, Can you make a video on UL throughput optimization?
@OurTechPlanet2 жыл бұрын
Sure, will add it to my To-Do list
@varun2846 ай бұрын
why did you stop making such informative video?
@OurTechPlanet6 ай бұрын
Just been tied up with job lately but will soon return with more exciting stuff.
@coolmunzir2 жыл бұрын
For Event A5, Serving Cell RSRP and NBR Cell RSRP both are checked that's why you preferring Event A5 instead A4 where once A2 Event is triggered then it all has to check if NBR Cell RSRP is better than a defined threshold, similarly IRAT Handover case with Event B1 & B2 Secondly Event A5 Serving Cell RSRP threshold should be less than Event A2 RSRP Threshold correct? From low priority RAT to higher priority RAT, IRAT Redirection is a better strategy or IRAT Handover is?
@OurTechPlanet2 жыл бұрын
Yes you are right. A5 threshold for serving cell should be lower than A2 threshold.
@OurTechPlanet2 жыл бұрын
For IRAT low prio to high prio, commonly redirection is preferred because of implementation issues.
@coolmunzir2 жыл бұрын
@@OurTechPlanet Also which Event A4/B1 or A5/B2 you will prefer and reason for that?
@HK_CryptoEnthusiast2 жыл бұрын
Brilliant explanation as usual 👌🏻
@OurTechPlanet2 жыл бұрын
Thanks for the feedback! :)
@sanjeev50782 жыл бұрын
Great Understanding Sir!!
@OurTechPlanet2 жыл бұрын
Thanks
@GhulamFareed-tk2sq9 ай бұрын
Excellent explaining
@OurTechPlanet9 ай бұрын
Thanks
@m.karthikeyan64822 жыл бұрын
Any suggestions for cloud with networking ?... Any ideas about cloud ?
@OurTechPlanet2 жыл бұрын
No, not at the moment :)
@mohammadearshad54362 жыл бұрын
Very informative session 👍
@OurTechPlanet2 жыл бұрын
Glad you liked it :)
@m.karthikeyan64822 жыл бұрын
❤️❤️❤️❤️❤️❤️Thanks for your effort 🙏🙏🙏🙏
@OurTechPlanet2 жыл бұрын
You are welcome!
@sauminkotadia75172 жыл бұрын
Nice one. But here in connected mode no where mentioned there are 2 thresholds for A5. One is for serving & other in for Nbr. Need to meet both after A2 trigger for Inter freq HO. Also one more query. In same technology during Inter frequency HO from lower priority frequency to higher priority frequency in connected mode, need to follow same process which u mentioned in example from higher to lower i.e. by A2 & A5 threshold? (As u mentioned that frequency priority is not really any role during connected mode)
@OurTechPlanet2 жыл бұрын
yes, you are right that there are two A5 Thresholds. Yes, in connected mode, coverage based handovers , the process is same. If Priority based IFHOs are enabled then the process changes slightly.
@avinashmvenugopalan57722 жыл бұрын
Hi can you please make a video on CORESET in 5G
@OurTechPlanet2 жыл бұрын
Sure, will create one
@zubairullahshah76892 жыл бұрын
Salam Ali, Thanks for your time to prepare Slide :) Well, I have question : This Setting Applicable for VoLte Handover Strategy as we have different Profile for Data and VoLte users. Thanks.
@OurTechPlanet2 жыл бұрын
Usually the data and VoLTE mobility should be different to maintain VoLTE's quality of service. These two sessions are more relevant to data rather than VoLTE.
@shoaibakram43992 жыл бұрын
well explained sir thank you.i have few topics in my mind NSA split bearer Types for reference signals in 5G 5G slot configuration and selection Coreset in 5G
@OurTechPlanet2 жыл бұрын
Thanks Shoaib, I will add them to my list :)
@debasishpanda67052 жыл бұрын
Sir it's better if you add another video for mobility optimization
@OurTechPlanet2 жыл бұрын
Sure, let me work on that as well!
@haideriful2 жыл бұрын
It will be great if u could make a full series of LTE