Thank you very much for the excellent video presentation. Yes, you are right, the sensor produces AC voltage, so which pins to connect makes no difference.
@matthewjuergens9183 Жыл бұрын
That's really cool. That little oscilloscope is awesome.
@jlsetnuper Жыл бұрын
thank you..
@meassavuth464910 ай бұрын
* Thank you very much sir , your video is very helpful, very important for any beginner repair man , and please show how to test oxygen sensor too , because i have look many other videos but it can not make me understand it , only your video can make me understand quickly , thanks
@jlsetnuper10 ай бұрын
Noted...thanks for viewing
@dwightjtaylor4 жыл бұрын
A revealing demonstration of an applied application.
@globalcommerce76543 жыл бұрын
Very good and excellent video! you are skilled!
@jlsetnuper3 жыл бұрын
thank you for your comment..
@paulfoldes3873 Жыл бұрын
excellent video thanks what kind of scope you are using
@randymccalla99952 жыл бұрын
Didn't notice, but did it ever output higher than 3.2 volts ?
@paulfoldes3873 Жыл бұрын
why can you connect crank censor to directly to osciloscope dso 188
@jlsetnuper Жыл бұрын
for bench testing, yes you can..because two wire sensor is magnetized and can produce its own voltage with metal..but you cannot do this with 3 wire sensor, you need a 5 volt bias voltage to work on oscilloscope..thanks for watching..
@asarcik11 ай бұрын
mine Crank sensor connector V is 2.38 but manual seys ; Measure the voltage between the 5V reference circuit and the chassis. = 4,8~5,2 V Measure the voltage between the CKP signal circuit and chassis. = 4,8~5,2 V is any vrong? or what ?
@jlsetnuper11 ай бұрын
thanks for watching...nothing wrong with the crank sensor
@nisri15673 жыл бұрын
Good job! It could habe been more interesting,if you could tell or show us, the pins of the Cam sensor. And during the test, what was at the two pins of the sensor connected? Power? How much? Or your volt meter prongs. Was the flat piece of metal a magnet? What was the minimum rpm of the machine. Thank you too.
@jlsetnuper3 жыл бұрын
the cam sensor produces a sine wave signal , so AC voltmeter probes can be connected either side of the pins..the piece of metal is a flat bar iron , cam sensor itself is magnetize..and the drill was set to 1 with a maximum rpm of 600. and the video shows that lower rpm produces lower voltage and high rpm with higher voltage on a good sensor..thanks for watching
@nisri15673 жыл бұрын
@@jlsetnuper you are really appreciated. Thank soo much for your polite and satisfatory informative soon reply.
@ronr77532 жыл бұрын
i use analog meters when doing these test
@titanchelito7413 жыл бұрын
Hola entonces ese sensor está en buen estado ? O está dañado? Esta bueno ? O esta dañado?
@jlsetnuper3 жыл бұрын
este es un buen sensor ... gracias por mirar
@rassieetchells58793 жыл бұрын
Hi. Is that a normal piece of metal plate that you use to check the voltage
@jlsetnuper3 жыл бұрын
It's a piece of metal that will attract magnet.. thanks for viewing
@ozriblit3 жыл бұрын
A piece of steel. I use an angle bracket because it is nearby.
@jinglethrushmusic24783 жыл бұрын
Good job.. can l use the same method on a 3 wire crank sensor?
@jlsetnuper3 жыл бұрын
yes, you need to know the pin out of the 3 wire sensor, you need to have a supply of 5 volt and the third wire to the multimeter or oscilloscope.
@jinglethrushmusic24783 жыл бұрын
Ok thanks 😊
@pavel73113 жыл бұрын
hi where does he get to buy that oscilloscope
@jlsetnuper3 жыл бұрын
you can buy it on ebay, just search for "oscilloscope DSO188" ... thanks for viewing
@vidrioandsonstrucking24222 жыл бұрын
mi sensor marca 513ohms entonses esta malo? espero me conteste gracias
@jlsetnuper2 жыл бұрын
hola, depende de la temperatura del sensor, si esta caliente tiene baja resistencia, si esta frio tiene alta resistencia..va de 300 - 2000 ohms..
@vidrioandsonstrucking24222 жыл бұрын
@@jlsetnuperok gracias
@mohamedfiraz70412 жыл бұрын
If this sensor wire is bad will the car starts ?
@jlsetnuper2 жыл бұрын
If sensor wire is bad the sensor will not work..and the car will not start..thanks for watching
@kennydoolarchan95152 жыл бұрын
@@jlsetnuper What is the name of the small oscilloscope? Where can I buy the Oscilloscope?
@jlsetnuper2 жыл бұрын
@@kennydoolarchan9515 you can buy it on ebay, search for oscilloscope DSO 188.
@pakiengr.8962 жыл бұрын
Whole KZbin no body knows..location of crank sensor on k6 Engine
@markim5087 Жыл бұрын
I don’t get why your not talking and explaining what your doing and looking for as your volume works, lol..I was a tech for 30yrs and taught auto electronics at UT , explaining in detail works better for those who don’t really get why sin wave your looking for.. on your oscilloscope