In this video I will demonstrate how to test signal wire with ohm meter and scan tool.
Пікірлер: 46
@dirkZigander4 жыл бұрын
Outstanding way of testing sig wires ! It is far more simple than Paul Danner's putting a 5k ohm resistor in series and is absolutely safe... Thank you for this vid and several of your other succinct vids . Thomas Jones, New Orleans, LA
@pinoyautomotogpsmaster2203 жыл бұрын
GREAT TUTORIAL BRO
@tony-le4nz6 жыл бұрын
Good job.......good class....!!
@alrifainidal4 жыл бұрын
awesome video . thank you very much
@arthurfricchione81197 жыл бұрын
Good informative video. Thanks for the tip
@kyhomegarage34307 жыл бұрын
Arthur Fricchione you are welcome I'm glad you liked it. Thanks for watching.
@pdrzone569710 ай бұрын
Great information 👍🏻
@ryanramlochan15043 жыл бұрын
Can you do a Hall effect crank sensor pull up type,how do you check the harness and what's the easiest way to understand a bias voltage
@alexthegreat52085 ай бұрын
What if you have an intermittent signal wire problem…can you just run a signal wire and connect it to the ecm to the crankshaft connector ?
@ashoksonagra195 жыл бұрын
How to test bosch crdi engine diesel fuel rail 3 pin sensor and 2 pin Actuator voltage?
@alyte114 ай бұрын
My Mt2400 only puts out 3.7v. I understand it doesn't matter for this test, but why would my MT2400 output differently than yours? Any idea?
@ahmeddokman45424 жыл бұрын
that would be much better if u have shown us how u connected the meters
@kyhomegarage34304 жыл бұрын
ahmed dokman unplug your sensor. Take your meter set it on diode mode. Take black lead and connect it to a good ground and take red lead and touch signal wire and watch your scan tool for response. 👍
@hinojosa5522 жыл бұрын
You need to show exactly how you connected the ohmeter, you had t&e camera too close and could not see anything how was connected , you explained it well but couldn't figure out how was connected the ohmeter to signal
@martinguitarhd287 жыл бұрын
Hi i tried this with both my dvom' s ..Put one on continuity and the other on volts DC and connected the leads to each other and my reading was .280v on the auto ranging setting .Was expecting i higher voltage than this .Does the auto ranging affect the decimal point position ? Thanks
@kyhomegarage34307 жыл бұрын
martinguitarhd28 something is pulling your voltage down. What is reading on your ohm meter should be OL.
@martinguitarhd287 жыл бұрын
Hi just to clarify that i am doing this correctly as i could not see how you connected your leads to the vantage and other dvom in the video .I have 2 dvom's .I set one meter to ohms setting and the other meter to volts DC .I put my red and black leads into one dvom and same again in the other dvom and join them together(one set of leads has alligator ends on) and then look at the voltage reading ? Always used the 5kohm resistor like Scanner Danner uses to do the signal circuit integrity test but like your idea as well.
@kyhomegarage34307 жыл бұрын
martinguitarhd28 send me your phone number to this email I will call you ruzic@bellsouth.net
@martinguitarhd287 жыл бұрын
Just like to add i am just connecting both meters together to find how much voltage my dvom puts out to see if it's 5v,2.80 or 3.5 v etc
@kyhomegarage34307 жыл бұрын
martinguitarhd28 yes and than you can use that voltage to test your signal wire and compare with scanner reading
@jonetrance4495 Жыл бұрын
hi i have a 2009 ford fiesta 1.6 tdci,i was driving it last week with no problems,then out of the blue a cog light came on which i have been told is the pcm light,the car died and wouldnt start for around 5 mins,eventually got it running and got it home,a friend plugged it in and a p0698 code came up,he said it was throttle pedal,so replaced that also put a new fuel filter after a day or 2 same thing happend,it wouldnt start so i put a forscan on it turned the pcm light off and it started,after 2 hours cut out again so i unplugged egr and it run fine for 2 days then the light came on again even with the egr unplugged,it has no problem starting but once that pcm light comes on the car will not start until i plug forscan into it and clear the p0698 code,is there anyone out there who can help it says sensor reference voltage c circuit low additional fault symptom circuit voltage below threshold......thanks in advance,jon
@hinojosa5522 жыл бұрын
Can you draw this one boar to see how is connected?
@pigeonsil240sx2 жыл бұрын
but if the sig can handle a short to ground why do we worry about meters and test lights?the amerpage draw from a short is emensly more and yet that doesnt destroy the pcm?
@kyhomegarage34302 жыл бұрын
I am not sure if I understand you question. Signal voltage can’t handle short to ground. It will be pulled down to 0 volts.
@edb3654 Жыл бұрын
If your signal wire greater then 5v from (+) to input and (-) to battery ground, would you include that the pcm is done?
@mersudinsalkic2366 жыл бұрын
sefe ako ikad budes imao vremena da napravis isti ovak video kad se mijeri volti kad se mijeri mili volti omi ii to sa ampermetrom tim zutim na nasem posto u mene googel translaid ne prevodi dobro Lijep pozdrav
@kyhomegarage34306 жыл бұрын
Mersudin Salkic vozdra, koristio sam ovaj metod u videu kada sam radio na senzoru za pritisak ulja na Chevy Suburban
@sonofsteve5662 жыл бұрын
have a Question: 5v at pcm ok, signal return has battery volt(12v plus), DTC-hard fault to CMP P0340 short in circuit,
@kyhomegarage34302 жыл бұрын
Unplug sensor and take test light connected it to ground and touch signal wire. If your test light lights up your signal wire is short to power
@sonofsteve5662 жыл бұрын
@@kyhomegarage3430 key on? what is the funcion of signal wire? basically a ground?
@kyhomegarage34302 жыл бұрын
@@sonofsteve566 yes key on. Signal wire sends signal to PCM
@sonofsteve5662 жыл бұрын
@@kyhomegarage3430 thank you, mechanically not bad with wrench, but not much experience with wiring been studying pin out and wiring diagram but little over welming when don't understand basic functions, appreciate your help
@sonofsteve5662 жыл бұрын
@@kyhomegarage3430 ok, tested light from ground to signal return, no light no short? what am i missing?
@ashoksonagra195 жыл бұрын
And cr injector volt
@hinojosa5522 жыл бұрын
A little confused when you don't see how is connected
@billg46302 жыл бұрын
Too many uhh uhh for me..thanks
@kyhomegarage34302 жыл бұрын
You wouldn’t benefit from this video anyway. Thank you for watching.