BEST Cab Access Door | Box Truck Conversion

  Рет қаралды 43,307

Nomad Brad

Nomad Brad

Күн бұрын

Пікірлер: 156
@1ZZFE
@1ZZFE 10 ай бұрын
Oh yes i love this door feature of your U haul RV truck. I think this is the greatest selling point. 😊
@mannys4036
@mannys4036 2 жыл бұрын
You are becoming, if not the master of the passthrough. Awesome.
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Haha I’m definitely getting it figured out
@mannys4036
@mannys4036 2 жыл бұрын
Your modest and humble. I love your builds and ever greater, the way you work with the books community; very inspirational. That will be my life in the near future.
@r.i.cmameaux1378
@r.i.cmameaux1378 Ай бұрын
i have been searching video about this for hours thank you very much!
@nomadbrad503
@nomadbrad503 27 күн бұрын
im glad you found me
@gadigo5
@gadigo5 Жыл бұрын
Best instructed video for that purpose,thank you.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Glad it was helpful!
@joeblow1942
@joeblow1942 6 ай бұрын
1) He paneled the inside wall of the box BEFORE cutting out and installing the door. 2) 0:35 There is a gap of about 5” between the box and front cab. 3) 1:03 He bought the 22” wide X 42” tall Lippert RV door off of eBay. 4) 1:49 Buy “Accordian Boot” from eBay, etc. to fill that gap. This has two metal clips that run along each edge. 5) 2:09 Trace door on cardboard for template with marker. 6) 3:01 Center template on wall and scribe line. 7) Drill pilot hole through BOTH so I can start cutting with Sawsal. 8) 8:01 Sawsall blade is 9” and rated for “wood with nails.” It can cut through BOTH walls at the same time. He suggests using two NEW blades. 9) 8:54 Tape along outside perimeter of line to protect the good edge. 10) 10:34 Cut out FRP frame using the same cardboard template for the door. Cut it so that it is about 27” wide X 48” tall. That’s about 3” wider and taller than the opening. 11) 11:56 He glued the FRP using ‘Loctite Powergrab All Purpise’ and self tapping screws about every 8”. 12) Install door. 13) 13:22 The boot clips on the edge of the installed FRP panel and the edge of the door. 14) 13:38 Start boot off center so if you step on it it doesn’t mess it up. 15)
@MAXIMUSMINIMALIST
@MAXIMUSMINIMALIST 10 ай бұрын
I have stressed out big-time trying to come up with a legitimate design for a U-Haul pass-through and never even thought of using a door like this! I did come up with a pretty good idea using pipe insulation on a PVC frame that can float as the seal and then just use a curtain Because the idea of creating a lip for the accordion seal like you did cross my mind but I just didn't see it as feasible and too much work but I guess compared to the other options it's a damn good idea! Another thing to keep in mind is that All of that needs to be sealed up like the world depends on it with silicone because if you start getting moisture into that plywood between the metal sheets that makes up the box walls you will essentially destroy the entire build when that wood rots.
@verocola6335
@verocola6335 17 күн бұрын
In the case of the UHAUL TRUCKS, the door space is fully covered, side to side, with the box extension towards the front, over the cabin, called by Uhaul, "Mom's Attic", which will prevent ANY water, rain snow or whatever from reaching the passthru door or frame.
@verocola6335
@verocola6335 17 күн бұрын
In the case of the UHAUL TRUCKS, the door space is fully covered, side to side, with the box extension towards the front, over the cabin, called by Uhaul, "Mom's Attic", which will prevent ANY water, rain snow or whatever from reaching the passthru door or frame.
@flowersafeheart
@flowersafeheart Жыл бұрын
I have no idea how doable this is for as beginner level as I am but maybe! Very inspiring video. Seems like it was very thought through.
@boriskarloff6356
@boriskarloff6356 Жыл бұрын
Good shit. I thoroughly enjoyed your tutorial video. Thanks buddy.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Thanks for watching, I appreciate you
@joelash6704
@joelash6704 2 жыл бұрын
Is this the love child of Johnny Knoxville and Jeff Goldblum?? Great video.
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Dear god I hope so
@followyourbliss101
@followyourbliss101 4 ай бұрын
i remember years ago on a move - think it was a ryder - but was the bigger 26 footer? and it had the pass through door. I thought these early 2000 15 footers were also like that but i see they are just like the new ones - separate crappy fiberglass cab back with the gap.
@nomadbrad503
@nomadbrad503 4 ай бұрын
I think this design is specific to uhaul. The ryders have the box connected to cab
@andrewroberts-hq4uu
@andrewroberts-hq4uu Жыл бұрын
Thanks, I was looking for information on a pass though. I did learn a lot, however I would the wall cuts individually.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Glad it was helpful!
@jwdeff
@jwdeff 10 ай бұрын
I second cutting the walls individually. Sawzalls don't like to stay straight. Maybe drill a small hole through the template and through both walls, then you have something to line up the template with, and can put the template inside the cab to cut the 2nd wall.
@jessicasoss1586
@jessicasoss1586 Жыл бұрын
I'm so glad I found your channel! I was thinking of converting an old uhaul. ❤
@nomadbrad503
@nomadbrad503 Жыл бұрын
You should!
@nomadicconquistador7-5-39
@nomadicconquistador7-5-39 Жыл бұрын
Cool video and tips. You got that Tony Stark look with the beard, "Ironman"..
@nomadbrad503
@nomadbrad503 Жыл бұрын
I appreciate you
@rturpening
@rturpening Жыл бұрын
What a phenomenal video, this was one part that was causing an issue for me, I'm gonna do it just like that and it's gonna be great, thank you!
@nomadbrad503
@nomadbrad503 Жыл бұрын
Glad it helped!
@verocola6335
@verocola6335 17 күн бұрын
In the case of the UHAUL TRUCKS, the door space is fully covered, side to side, with the box extension towards the front, over the cabin, called by Uhaul, "Mom's Attic", which will prevent ANY water, rain snow or whatever from reaching the passthru door or frame.
@nomadbrad503
@nomadbrad503 17 күн бұрын
This is true until you are driving while it’s raining. Ask me how I know
@CarrieMtn
@CarrieMtn 2 жыл бұрын
Pretty nice. Good idea to use an RV door. Would it be possible to put the lock in the other side? Also the FRB was clever. I’ve seen other methods and this looks nicer.
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Thanks, the lock should be on the other side to be functional for this build however it can’t be reversed. I’ll add some type of lock on the inside to keep people from entering the box if they get inside the cab
@Ariiiilola
@Ariiiilola Жыл бұрын
@@nomadbrad503 very helpful..I want to learn to be this handy🙂sad we must be so careful with other Humans😔plz learn how Jehovah God will Soon make ALL Earth 🌎🌍 Safe no violence no war no death perfect world Forever @JW/Jehovah's Witnesses
@christophergwara2422
@christophergwara2422 Жыл бұрын
Keep striving
@J1I9M7M4Y
@J1I9M7M4Y 24 күн бұрын
Really good info!! Do you know if there is some kind of insulated accordion boot for use in arctic climate?
@sundog3203
@sundog3203 2 жыл бұрын
Nicely done, Brad! 😊
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Thanks!
@pmclellan123
@pmclellan123 2 жыл бұрын
Nice work. Your video and instructions were really clear. I would worry that the initial hole may not line up perfectly with the cab spot if your angle was a bit off as you go through the box. Maybe a pilot hole the same size as the centre drill would help guide it to the exact spot. Maybe I’m being overly paranoid but I would hate to screw this important cut up.
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Yeah the initial circular hole is not that critical..it’s the sawzall part that needs to be straight and those blades can bend especially when they get hot. Mine wasn’t perfect but I went back and trimmed it out. As long as you’re close, it works out
@williamwoolcock
@williamwoolcock Жыл бұрын
It's probably good that you're doing this as the first thing you do.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Yes, this should definitely be a first step
@darknessislight3689
@darknessislight3689 Жыл бұрын
This is awesome 👍🏾
@joeblow1942
@joeblow1942 6 ай бұрын
Brad, a couple questions, please… 1) After installing the FRP frame, does it extend past the door opening about 1” all the way around? 2) To keep the boot in place forever, would it help to apply contact cement to the boot and the edge of the FRP frame it attaches to? 3) Should I order a boot for a 5” wide gap? Thanks!🤙🏼
@nomadbrad503
@nomadbrad503 6 ай бұрын
yes frp is extended all the way around. yes you could use an adhesive on the boot if you like. I dont remember what boot i ordered but 5" sounds about right
@truebluepatriot2739
@truebluepatriot2739 Жыл бұрын
🇺🇲🇺🇦 Ok first I'd like to say this was the first time I have come across one of your videos and it was awesome, but: 1 - for a less adept self doer as myself I wish you had included the How to cut, place & attach FPR Board. 2 - I would of liked to have seen the finished doorway with the door open and closed from the front of the cab. 3 - As an FYI, placing the seam of the boot closer toward the door hinge side of the opening would I think, better keep the boot safe from being stepped on. Again awesome vid and thanks so much for putting it out there especially for us paint by the number types. 🤪 🙏☮🙏 Ps - In the cab loved seeing your doggie-dog in his/her bed. He/she is very beautiful!
@nomadbrad503
@nomadbrad503 Жыл бұрын
I appreciate you
@montanaswenson9765
@montanaswenson9765 4 күн бұрын
I think you did a great job. I have a question about the lock. Shouldn’t the lock handle be inside the cab?
@nomadbrad503
@nomadbrad503 3 күн бұрын
yes it should. unfortunately this lock cant be flipped to the other side
@letsgetreal670
@letsgetreal670 Жыл бұрын
Very cool! One of the best pass-through ideas I have seen. How did you work around the interior portion of the lock being on the cab side where it can be unlocked easily by an intruder? Thanks.
@nomadbrad503
@nomadbrad503 Жыл бұрын
The door opens into the box so when I pull the bench out into bed configuration it’s impossible to open that door. I do that for extra security if I’m leaving the van parked somewhere sketchy
@benfletcher6365
@benfletcher6365 2 жыл бұрын
Excellent video
@nomadbrad503
@nomadbrad503 2 жыл бұрын
I appreciate you 😎
@benfletcher6365
@benfletcher6365 2 жыл бұрын
@@nomadbrad503 I want to do similar with a 26' uhaul. Build as I go. .
@terryryan4106
@terryryan4106 2 жыл бұрын
Great instructional video Brad
@nomadbrad503
@nomadbrad503 2 жыл бұрын
I’m glad it helped!
@cic-jakevanddalgeemyers.2739
@cic-jakevanddalgeemyers.2739 2 жыл бұрын
Super cool 😎...
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Thanks 😊
@PsychoSweethardt
@PsychoSweethardt 11 ай бұрын
Nomad Brad, thanks for the great video! Any suggestions on how to do something like this when the box truck has a window spanning the back wall of the cab?
@nomadbrad503
@nomadbrad503 11 ай бұрын
Well, you’ll have to remove the window. You can then make the opening the same size as the window opening or you’ll have to fill the gaps with plywood to make it smaller
@elsuperpollo2273
@elsuperpollo2273 8 ай бұрын
I plan on doing something Similar to a 10 foot box truck, but add shelves and a right hand drive kit and use for rural postal carry.
@nomadbrad503
@nomadbrad503 8 ай бұрын
That’s a great idea!
@elsuperpollo2273
@elsuperpollo2273 8 ай бұрын
I'm stoked to modify one
@thetattooedpainter
@thetattooedpainter Жыл бұрын
well done. nice breakdown.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Glad it helped
@azvwbaja
@azvwbaja 2 жыл бұрын
Great job buddy
@nomadbrad503
@nomadbrad503 2 жыл бұрын
I appreciate your support
@symcardnel1741
@symcardnel1741 Жыл бұрын
Love your stuff man. I can't wait till your at 500k subs. I'm guessing only a build or two away. If not, maybe try jumping out of a plane with only a cordless drill and a fan flade in the chuck. Is the cab loud as fuch with just the rubber gromet in place? I'm talking on the interstate. Keep up the great fun!!
@nomadbrad503
@nomadbrad503 Жыл бұрын
Thank you 🙏🏻 the cab is louder with the passthrough than without but the rubber boot dampens it down. To me, not a big deal. I still prefer it over an open cab like sprinter where you have to listen to all your stuff banging and rattling around. I can take phone calls and enjoy the stereo in peace
@gezor20
@gezor20 Жыл бұрын
great stuff! Would it be possible to somehow insert a sliding door in that area? Insulation will become an issue of course, and connecting the cordeon. But maybe there is a way?
@nomadbrad503
@nomadbrad503 Жыл бұрын
There is always a way. If you can dream it, you can do it!
@johncaldwell2114
@johncaldwell2114 Жыл бұрын
I love the door. I've been looking for it from Lippert online referencing the numbers on the sticker you showed. I can't seem to find it yet. Where did you purchase it?
@nomadbrad503
@nomadbrad503 Жыл бұрын
i got it on ebay. there was a seller with multiple styles for sale
@dodgeramsport01
@dodgeramsport01 Ай бұрын
Dude, good work, but you over complicated that measurement to find center! lol Half of the wall would be 46in, make your mark, then half of the template is 10.87 inch, make your mark, then line up your marks! Its that easy!
@hungrycamperfilms
@hungrycamperfilms 9 ай бұрын
How did you seal the accordion from the outside (between cabin and the box)? Now when it rains, the water stays on top of that accordion boot and might get inside the plywood wall.
@nomadbrad503
@nomadbrad503 9 ай бұрын
I sealed the edge of the box with silicone and the van box has an overhang that extends over the cab. It does not get wet when raining
@rabradley1701
@rabradley1701 2 жыл бұрын
With the expenses of apartments getting really exspensive in MD I kinda am going to be doing something like this so in cases if people get on my nerves I can takey house with me lol how much does this kind of thing cost
@nomadbrad503
@nomadbrad503 2 жыл бұрын
20-30k if you diy
@rabradley1701
@rabradley1701 2 жыл бұрын
@@nomadbrad503 thank you for letting me know appreciate it
@JoeJohnson-qf2jg
@JoeJohnson-qf2jg 11 ай бұрын
Nomad brad why don’t you do a complete build on a box truck series?
@nomadbrad503
@nomadbrad503 11 ай бұрын
I filmed what I could. Life gets busy and I work while living in this full time. didn’t have the time to do a full dedicated build series. Filming while building takes twice as long. And sometimes I just need to bust out projects.
@hadassahrivkah5993
@hadassahrivkah5993 8 ай бұрын
Could I still have use of that third jumper seat? Like does it bend forward in half or…? Love this but I need three seats. :)
@nomadbrad503
@nomadbrad503 8 ай бұрын
The jump seat is fixed and does not fold. You will not be able to use a door if you keep the seat. Unless you make a custom jump seat but then it will still be difficult to climb over the seat into the back
@wckdaintgood
@wckdaintgood 2 жыл бұрын
Bro when it comes to your electric system could you please go in depth and try to easily explain it. I just bought an old fedex step van and I’m currently saving up to convert mine. I’m only 20 and have veryyyyy little electrical work outside of school. I’m pretty sure I can figure everything else out but the electrical and solar shit makes me nervous. Love the vid btw
@nomadbrad503
@nomadbrad503 2 жыл бұрын
You got it man, I’ll have several videos covering electrical. I also plan to do some live streams to answer questions on electrical and solar
@abbou1189
@abbou1189 10 ай бұрын
Good afternoon.please provide the address wehere i can order a door for passage to the cabin Many thanks
@nomadbrad503
@nomadbrad503 9 ай бұрын
i purchased it on ebay its a lippert 42" entry door
@1stJohn3.9-10
@1stJohn3.9-10 5 ай бұрын
Hey Brad, I can't find any videos on making a door from the Crew Cab back to the flat bed. Would it be the same as a box truck?
@nomadbrad503
@nomadbrad503 5 ай бұрын
I think a crew cab is a lower ceiling height but otherwise the same process
@1stJohn3.9-10
@1stJohn3.9-10 5 ай бұрын
Awesome, I just want to create a crawl space to access Bedding, gym bag, etc
@derelictegrasshopper
@derelictegrasshopper Жыл бұрын
how did you get the self-tapping screws drilled into place (mounting the FRP to ext. of cab) with there being such a small amount of space between cab and box to fit an impact driver or drill?
@nomadbrad503
@nomadbrad503 Жыл бұрын
I have a 90 degree impact drill adapter. Can find them online or Home Depot
@stephv7326
@stephv7326 Жыл бұрын
I got a 2006 3500 chevy box truck, I've been wanting to convert our box but idk where to start, where to go to get the right screws boards etc etc. I'd like to make half into home like look, carpet sofa or bed then the other half turn that into a tool box cuz my dude owns his selfmade 57years of successfully mechanic business, he wants to try mobile mechanic thing nd got the truck to turn into tool thing. (wanting the whole truck to be one but no, I'm putting a cozy space for me in it too lol. ) the whole interior needs a upgrade. can u do a video on a chevy box truck
@nomadbrad503
@nomadbrad503 Жыл бұрын
I don’t have a Chevy box truck.
@jedics1
@jedics1 Жыл бұрын
Ive considered doing this on my truck many times but my motor is directly below the cab so I imagine a huge increase in motor and road noise if I were to do this leading to fatigue on long trips. Did you notice a lot more noise while driving after? It would be more difficult but putting the door on the cab side would have helped.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Yes there is more road noise, not huge amounts.
@montanaswenson9765
@montanaswenson9765 4 күн бұрын
Centering would be easier if you did corner to corner with chalk line on wall and then again on the cardboard.
@nomadbrad503
@nomadbrad503 3 күн бұрын
thanks for the tip
@williamwoolcock
@williamwoolcock Жыл бұрын
Thank you for muting the Sawzall.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Absolutely
@truthofgod6213
@truthofgod6213 Жыл бұрын
Hey Nomad Brad, how did you connect the accordion boot to the RV door aluminum step plate? This door I just got has no edge on the step like the rest of the frame.
@nomadbrad503
@nomadbrad503 Жыл бұрын
I was able to attach the boot the the very edge of the step plate. It’s not as deep as the rest of the frame but it still connects
@agent5758
@agent5758 6 ай бұрын
how did you get the seat off, i been twisting the bolt with a wrench and it aint going no where just keeps spinning
@nomadbrad503
@nomadbrad503 6 ай бұрын
you have to hold the bolt stationary while you loosen the nut. either you need someone on top holding the bolt or you can put a wrench over the bolt and zip tie it to the base of the chair to keep it from moving ( thats what I did )
@jamesoldman3021
@jamesoldman3021 4 ай бұрын
Would there be any reason to install a door in the cab and another door in the box? I'm thinking two doors would make it quieter so anything rattling in the box would not be heard.
@nomadbrad503
@nomadbrad503 4 ай бұрын
no, there is not room for a door to swing inside the cab
@seashackf1
@seashackf1 23 күн бұрын
Maybe a sliding door inside the cab would fit.
@ExMoe1998
@ExMoe1998 7 ай бұрын
could a person make an opening the entire width of the cab or would that take away too much stability?
@nomadbrad503
@nomadbrad503 7 ай бұрын
Yes, I have seen it done. I prefer to keep them separate so the drive is quiet. Otherwise you hear everything rattling and banging around
@mavallarino
@mavallarino Жыл бұрын
Is this a purpose pass-through door? Because the door’s key side should be on the cab side (not on the box side).
@nomadbrad503
@nomadbrad503 Жыл бұрын
It was done on purpose. The door needs to swing open into the box not the cab. And the locking mechanism can’t be reversed. To block access through the passthrough I just slide out the bench about 6” makes opening the door from cab impossible
@Carlos-lq6hd
@Carlos-lq6hd 2 ай бұрын
I want to do the same in my box truck 🙏 how can we connect
@Sam-gf1eb
@Sam-gf1eb 2 жыл бұрын
Do you trust the aluminum to hold on the accordion boot? I feel like it will fall of some time, would it be safer to add a few screws?
@nomadbrad503
@nomadbrad503 2 жыл бұрын
The accordion boot has metal clips built in that secure it to the aluminum door frame. If you screw through the boot it will no longer be air/water tight. If you’re concerned about the boot falling off you could use an adhesive. This is the method I used in my last box truck. It lasted 2.5 years without falling down
@larryclark5355
@larryclark5355 Жыл бұрын
How did you get the screws into the FRB, not much room to work!
@nomadbrad503
@nomadbrad503 Жыл бұрын
Correct, I used a dewalt right angle attachment with self tapping truss head screws. It’s a tight fit but it does fit
@larryclark5355
@larryclark5355 Жыл бұрын
@@nomadbrad503 Thank You,Very Nice work
@vanman3752
@vanman3752 Жыл бұрын
Wow, that's exactly what I've been looking for but I went to the Lippart website and it doesn't look like they have that door anymore. Did you order it as a special size or something?
@nomadbrad503
@nomadbrad503 Жыл бұрын
No, I found it on eBay
@vanman3752
@vanman3752 Жыл бұрын
@@nomadbrad503 Thanks, I'll see if I can find it there.
@nomadbrad503
@nomadbrad503 Жыл бұрын
@@vanman3752 there’s a similar one for sale right now www.ebay.com/itm/266073286975?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=5NfBMjPbQSG&sssrc=2349624&ssuid=-iV6hQS6SbO&var=&widget_ver=artemis&media=COPY
@vanman3752
@vanman3752 Жыл бұрын
@@nomadbrad503 It didn't last long and I did see his other doors but most of them are damaged more than I care for and the shipping is outrageous. Thanks anyways for the tip. I'm trying to find a source close enough I can pick it up and save the shipping cost.
@yacoubattaallah1928
@yacoubattaallah1928 6 ай бұрын
I have a question what the name of the rubber or where you buy it Thanks
@nomadbrad503
@nomadbrad503 6 ай бұрын
It’s called “accordion boot”. I bought it on eBay
@yacoubattaallah1928
@yacoubattaallah1928 6 ай бұрын
@@nomadbrad503 can you send me the link please
@yacoubattaallah1928
@yacoubattaallah1928 6 ай бұрын
@@nomadbrad503 thanks I found it 🙏🙏
@maucelioperez9847
@maucelioperez9847 10 ай бұрын
where you bought the door and where you got the door package.
@nomadbrad503
@nomadbrad503 9 ай бұрын
i purchased it on ebay its a lippert 42" entry door
@maucelioperez9847
@maucelioperez9847 9 ай бұрын
the door comes with the inpaque included
@nomadbrad503
@nomadbrad503 9 ай бұрын
@@maucelioperez9847 what’s a “inpaque”?
@nomadbrad503
@nomadbrad503 9 ай бұрын
@@maucelioperez9847 www.ebay.com/itm/266298217490?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=5NfBMjPbQSG&sssrc=4429486&ssuid=-iV6hQS6SbO&var=&widget_ver=artemis&media=COPY
@fartsonbasketball9206
@fartsonbasketball9206 Жыл бұрын
How much do you charge for insulation, flooring and can access conversion?
@nomadbrad503
@nomadbrad503 Жыл бұрын
I do the conversions for my own vehicles. Unfortunately I am not for hire
@cheree3009
@cheree3009 9 ай бұрын
How could you do this in a cab with a wide back window?
@nomadbrad503
@nomadbrad503 9 ай бұрын
You would need to remove the window, cut in the door and fill in the excess space that was occupied by the window…still very possible
@cheree3009
@cheree3009 9 ай бұрын
@@nomadbrad503 Thanks! Please do a vid if you ever do one, love your videos!
@glentreasure2466
@glentreasure2466 Жыл бұрын
Just like a RV window or a roof of a car or summer just like it but a little bit bigger a lot bigger a doorway, same thing
@zaybrownisanbrand4427
@zaybrownisanbrand4427 Жыл бұрын
Do you have an facebook page so I can send some pictures of my 28footer i would love your input and ideas on what I can do to make a sleeper thanks
@somoscallejero
@somoscallejero Жыл бұрын
yo quiero uno asi
@hash641
@hash641 2 жыл бұрын
Where to buy this door ???
@nomadbrad503
@nomadbrad503 2 жыл бұрын
I bought this on eBay
@1966cambo
@1966cambo 2 жыл бұрын
You know you could just tape the shoe of the sawzall and not tape the wall right?
@nomadbrad503
@nomadbrad503 2 жыл бұрын
You can but on my last build the shoe rubbed through the tape and scuffed the wall so now I tape both surfaces. Just in case.
@1966cambo
@1966cambo 2 жыл бұрын
FRP Fiberglass Reinforced Plastic Not panel
@nomadbrad503
@nomadbrad503 2 жыл бұрын
Thanks man!
@verocola6335
@verocola6335 7 ай бұрын
As any space inhabited by a human being, there is the possibility of an EMERGENCY, for example a FIRE, or an accident, or whatever, the situation REQUIRES 2 ESCAPE ROUTES, one at the back door and a second one at the front. JUST BASIC SAFETY !
@verocola6335
@verocola6335 7 ай бұрын
BOTH DOORS ALWAYS.. ! MUST BE ABLE TO BE QUICKLY OPENED FROM INSIDE THE VEHICLE
@nomadbrad503
@nomadbrad503 7 ай бұрын
I agree with you!
@nomadbrad503
@nomadbrad503 7 ай бұрын
absolutely!
@___David___Savian
@___David___Savian Жыл бұрын
Sorry. But, that is a crappy door because no matter how strong the metal is...... everything on Earth is only as strong as it's weakest part. The glass in the middle can be broken in 2 to 5 seconds and it's big enough for a small man to get through it. So, again sorry. But, you don't have a safe enough door installed, especially if you are away from your truck.
@nomadbrad503
@nomadbrad503 Жыл бұрын
Sir, I am not building a panic room here. Anyone could just smash out the drivers window and Hotwire this van if they wanted to do me dirty. The strength of the little door in the middle means nothing. And this is in fact an exterior door from an RV so you could say the same thing about every rv that has been manufactured with a window..someone could break out the glass and climb inside. 🤷🏻‍♂️
@___David___Savian
@___David___Savian Жыл бұрын
@@nomadbrad503 American ingenuity at it's best. LOL.
@MAXIMUSMINIMALIST
@MAXIMUSMINIMALIST 10 ай бұрын
lol you should have stayed in school. He didn't want to come out and say it but we all know the reason for a pass-through door is in case of horrible weather when you arrive or depart your parking space and also if anything shady would be going on in the area and you want to depart safely without having to exit the vehicle. This is why most pass throughs use a freaking curtain! NOTHING you said has ANYTHING to do with ANYTHING. In fact, the points you made are among the most irrelevant I've ever heard in 55 years walking this planet.
@twentybucksorless
@twentybucksorless 2 ай бұрын
All that math for nothing ust findtthe center of cardboard and wall
@pedro-v2g3j
@pedro-v2g3j Жыл бұрын
9:28 lol clown the trim is going to hid that cut. smh
@nomadbrad503
@nomadbrad503 Жыл бұрын
🤡
@pedro-v2g3j
@pedro-v2g3j Жыл бұрын
@@nomadbrad503 lol, nice job though.
Uhaul to tiny home  | I LIVE HERE
11:41
Nomad Brad
Рет қаралды 597 М.
Roll up Door Conversion | Box Truck RV door install |
20:52
Nomad Brad
Рет қаралды 10 М.
БУ, ИСПУГАЛСЯ?? #shorts
00:22
Паша Осадчий
Рет қаралды 3 МЛН
Farmer narrowly escapes tiger attack
00:20
CTV News
Рет қаралды 11 МЛН
Box Truck to RV!! Was it worth it??
29:13
HR Headlight Restoration
Рет қаралды 625 М.
Tiny Home Hidden in a Box Truck - Stealth Apartment on Wheels
19:30
Tiny Home Tours
Рет қаралды 319 М.
We turned a Giant box truck into a Mobile Tiny House
20:06
GTVANS
Рет қаралды 138 М.
Box Truck Conversion Van Tour || Full-Time on the Road in Tiny Home
14:04
How to Convert a Box Truck to a Tiny House
13:29
Cole Webb
Рет қаралды 1,1 МЛН
His affordable home hidden inside of a work truck?!
22:39
Tiny House Giant Journey
Рет қаралды 1,9 МЛН
SIMPLE Insulated Subfloor |  Box Truck Conversion
22:35
Nomad Brad
Рет қаралды 13 М.
Functional DIY Box Truck Camper - Stealth Tiny Home
21:19
Tiny Home Tours
Рет қаралды 167 М.
Turned a delivery truck into a tiny house.
16:51
Canadian Stealth
Рет қаралды 1,9 МЛН
БУ, ИСПУГАЛСЯ?? #shorts
00:22
Паша Осадчий
Рет қаралды 3 МЛН