Bestway lazy spa e01 e02 e03 e04 error

[@massimilianodimauro2826]

Hi Great video for me as I got the exact same one and I now know what’s under that cover. My heater is working fine but it’s noisy before it would just hum . I’ve been told it’s the sensor by best way that the sensor is stuck and I must drop the whole from a little height to shake the sensor free. I’ve done that a few times now and still noisy what can you tell me I need to do next. Should I strip the sensor down and clean it out like you say on this video. Thanks Max

[@johnbeach1339]

Great video! I don't suppose you have any video of removing the pump so you can change the impeller?

[@grizzlyfn393]

I'm afraid not, it hasn't failed me yet, but I'm sure it won't be long.

[@claudiobertolotto8242]

a simply question: to remove the cover is it sufficient to unscrew all the screws at the base? Thanks

[@rdb1603]

Hi any idea about an e12 error on the same pump as you have. I have changed the intake line gaskets but still coming up with e12

[@Absolutedetailing]

I’ve got a Hawaii pro jet. It’s giving me e02 even with new filters. Jets work but when heat/filtration is requested, 4 seconds of silence it throws the code. What you reckon? 😊

[@grizzlyfn393]

Flow switch or a blockage

[@Absolutedetailing]

@@grizzlyfn393 thanks buddy. I checked the filter switch, it seems to function as I tested with magnet against the proximity sensor. Water certainly seems to come through the heater via gravity as I found out by accident. I’m wondering if the filter pump is faulty, have you had any dealings? It doesn’t even try and hum.

[@grizzlyfn393]

@@Absolutedetailing change the pump. 👍

[@Leo-gt1bx]

The pump I am trying to fix has no heat and no error codes. All sensors and flow switch are good and so are the elements. The customer changed the heating unit. Is wiring the elements in the incorrect sequence going to cause a problem?

[@evoqueupgrades3055]

Hi very useful video. Do you know where the impeller is situated?

[@darrenroberts2162]

Hi do you need water running through too clear 04 code

[@chriscallaghan1507]

I need a matrix for my maldives. On eBay, all the matrixes seem to be for an 'egg' because the heater reset button is at a 45 degree angle to mine, so that it will fit the curves of the egg. Where can i source the correct type, even if it means buying a new part, not 'refurbished, descaled'? Thanks.

[@grizzlyfn393]

Where are you based?

[@ritenalves1]

I have error code 04, how to solve it

[@justinehigginbottom2116]

You know that yellow looking thick elbow pipe....have you any idea where I can buy one mine is pouring out water...it has cracks all around the pipe

[@grizzlyfn393]

No sorry

[@petebenns2124]

Hi I bought a car silicone turbo 45 degree elbow and that fitted and no leaks. you need to make sure u get the correct inner dimension 50mm i think but please check and it was 100mm long

[@Chopper5175]

Hi..great vid . After hours of looking for vids and information regarding this type of pump, finally someone has posted something. I have an issue, the heater works and is getting to temp but when i press the pump it justs hums away.. nothing any ideas ? Also no error codes .

[@grizzlyfn393]

Sounds like a blockage. Remove and check the pipes. Failing that, the jet pump may have failed.

[@tonyboak5644]

My best ways Palm Springs water hose has split in it so I can’t use jet,water sprays everywhere,can I fix it?

[@traceybeswick-rs2uf]

Hi can you help, we have the same pump and every time we put the bublles on water comes out of the bottom of the pump. can this be fixed?

[@wilwilliams880]

Can you help with E3 code on Netspa Poolstar please. Filter does not pump water. Bubbles work

[@Skylark1971]

hi, i have a Miami hydro jet and repeatedly keep getting the E02 fault, i have reset the pump, disconnected the pipes and cleaned and flushed back pipes with a hose pipe. all the jets work fine but as soon as i put the filter on it goes into error again!!!!! any suggestion please

[@grizzlyfn393]

The video

[@mattnaylor145]

AMAZING

[@rebbecawhite8219]

Is there anyway to by pass the error e04 heatting error i have tryed everything .. works for 10 mins then pops into error again

[@grizzlyfn393]

No. You have to clean the heater matrix