HOW TO: Fix an EO2 error | Lay-Z-Spa, Coleman Saluspa, BestWay Saluspa, Inflatable Spas

How to fix an EO2 error | Lay-Z-Spa, Coleman Saluspa, BestWay Saluspa, Inflatable Spas
The EO2 error can affect all Lay-Z-Spa, Coleman Saluspa, BestWay Saluspa, Inflatable Spas hot tubs
There are several causes which can be fixed quickly and easily.
Reason 1: Stopper Caps
Leaving the stopper caps on can cause an EO2 error when operating the pump.
Step 1: Remove the stopper caps
Step 2: Turn the pump off and at the power supply
Step 3: Restart the pump.
Reason 2: Dirty filter
A dirty water filter can cause water flow issues resulting in an EO2 error.
Step 1: Remove the filter housing
Step 2: Remove the filter
Step 3: Clean the filter using warm water
Step 4: Restart the pump.
Coleman SaluSpa: amzn.to/3i4iZIQ
We have had our for over 4 years and have absolutely loved it!
Pool&Spa Small Pool 1" Chlorinating Tablets
amzn.to/3qRhja2
As an Amazon Associate I earn from qualifying purchases.
#colemanspa #layzspa #bestwaysaluspa #familydiy #colemansaluspa #e02error

[@FamilyDIY]

How to fix an EO2 error | Lay-Z-Spa, Coleman Saluspa, BestWay Saluspa, Inflatable Spas The EO2 error can affect all Lay-Z-Spa, Coleman Saluspa, BestWay Saluspa, Inflatable Spas hot tubs There are several causes which can be fixed quickly and easily. Reason 1: Stopper Caps Leaving the stopper caps on can cause an EO2 error when operating the pump. Step 1: Remove the stopper caps Step 2: Turn the pump off and at the power supply Step 3: Restart the pump. Reason 2: Dirty filter A dirty water filter can cause water flow issues resulting in an EO2 error. Step 1: Remove the filter housing Step 2: Remove the filter Step 3: Clean the filter using warm water Step 4: Restart the pump. Coleman SaluSpa: amzn.to/3i4iZIQ We have had our for over 4 years and have absolutely loved it! Pool&Spa Small Pool 1" Chlorinating Tablets amzn.to/3qRhja2 As an Amazon Associate I earn from qualifying purchases. #colemanspa #lay-z-spa #bestwaysaluspa #familydiy #colemansaluspa #e02error

[@pattyh4782]

When I hit the "bubble" button, to inflate the spa, nothing happens. Light is on, but no sound of a motor. I pushed the reset button on the side of the unit, but nothing is happening. Any ideas?

[@JennJenn101]

Hey you have a filter on the bottom inlet Aswell? What is the bottom inlet for?

[@MrWillabob]

@@JennJenn101 to let the water circulate......... OBVIOUSLY

[@garyd7289]

Great information and much appreciated sir!!! I did find that you do not have to take the hoses off, you could actually use your hose sprayer inside the spa and blow water through the pump through the filter port after removing filter. I was able to blow slimey debris out of mine the downside is it will go back into your spa nothing my vacuum wouldn't clean up and it isn't much debris.

[@leche1971]

I replaced my filter and that didn't work so I cleaned out the entire pump. Took it apart from the hot tub .. flushed it and I didn't see much sludge or debris come out. I refilled the hot tub and the e2 message comes on. As soon as I power on the pump. It does not begin to circulate when you turn on the heater button. It threw the e2 before I did anything at all. I've cleaned it out several times. I don't know what else the problem could be

[@juliemorrisdesign1]

Also need to check minimum and maximum water lines - if not between those two marks, it could cause 02 error.

[@imdeplorable2241]

Cleaning the filter doesn't work all the time. Even a new filter is not a guarantee. I've found that upon startup, an air bubble (in the pump, I believe) will throw an E-02 code. Taking both the filter and the chlorine/bromine tablet holder off and turning it back on for about 10 seconds pushes that air bubble right out. Then, just put the filter and tablet holder back on. Works every time for me.

[@FamilyDIY]

Thank you for sharing! Great tip!

[@billymacktexasdetective5827]

Thanks for the tip, removing those and running it is what fixed mine...

[@ryant8479]

Thanks dude

[@drok3333]

I did that and it ran without giving the E2 error, but when I put them back on it happened right away again. I haven't tried a new filter yet but it's there any other reason for an E2??

[@ryant8479]

@@drok3333 the filter holder itself can hold air bubbles as well. before attaching the filter holder again try tilting it all different directions while in the water to release trapped air. the best solution I've done is changing the filter underwater without bringing anything to surface... no chance for air pockets! or else you'll fight that e2 error every time you try to change it

[@bellarouxllc6160]

I only had my spa a few days only used it twice. Did everything in this video nothing worked. After my own trouble shooting I found out that I had my filter cap screwed in to tight. Due diligence paid off I did not want to deal with customer service. Great vid. Any problems I have in the future I will be sure to come here first.

[@Luminousmorrow]

Thank you!! My spa was only three weeks old, so i didnt understand why that message was coming up. The filter was in fact dirty dirty!! Seems to be running much better.

[@thomasverhoeve7930]

Had to spray water down the filter as I turned the pump on, finally worked. Thankyou Sir!

[@FamilyDIY]

Glad I was able to help!

[@jakedollins1710]

thanks for the help! i bought a brand new one and we have very mineralized water because we live in the country! Had no idea how these worked and after a day of trying to heat it, it got stuck at like 84-86 and we were worried and confused!!! Found your video, cleaned it off, and hot tub is heating so much faster!!! THANKS TO YOU AND THE FAMILY! You are appreciated

[@valerierichardson873]

Thanks you for the video and everyone taking time to share their experiences. Tonight was the first night I’ve had to get in the hot tub, went out during daylight and everything was great, got ready to get in and it threw this code. Changed extension cords thinking maybe the yard guys nicked it, but no go. Tomorrow when it’s daylight I will try these steps. Fingers crossed!

[@nkeely35]

Did you ever get it worked out?

[@valerierichardson873]

@@nkeely35 Yes! Changing the filter worked!

[@thecrazyhatman]

Thanks for this! This little spa has quickly become the highlight of my evenings and I was able to get it working again quickly with your vid :)

[@kayannahufford340]

Thank you so much. You saved me so much worrying about my hot tub. I put a clean filter and it works perfect. Thank you again.

[@FamilyDIY]

you are welcome

[@jenniferbattista7806]

I agree! Iclean my filter every use. I just alternate between two filters, hosing one out and storing it for the next day. Mine is 3 1/2 years old and so easy to maintain with daily filter cleanings. When I’m not home I don’t have to change them daily bc I’m not using it and it stays clean. Thanks for your videos ;)

[@carminejames2185]

I was given the tub second hand and almost sold it , but, I decided to give it a chance and do a lil research. I got the E02 error code a few times and your video helped immensely

[@kel7217]

Thank you! I’m a new owner to one of these and it scared me! I took the filter out and did exactly what you did! It’s working again! Hopefully it’s all good to go!

[@FamilyDIY]

You are welcome. This error message is very common and you will probably get it a lot, but it never stopped me from enjoying it

[@suvioblue]

To all, every time you take the filter out, before reconnecting the filter housing, make sure you shake it under water to get all the air bubbles out of it.

[@FamilyDIY]

Excellent point

[@mikemcmo]

Now THAT is something the instrucitons could include if they used words instead of cartoons! Thanks for the tip.

[@JackPC]

Thank you. That fixed the problem. Appreciate you taking the time to make enjoying the hot tub much more fun.

[@bradyseilhamer7184]

This just happened to me with mine and I came across your video and it’s a great help

[@kathleenfowler9598]

Omg, thank you for the tip at the end! It's already raised 1° and it's only been 5 minutes🎉🎉🎉

[@FamilyDIY]

One degree in 5 minutes! Did that continue at that speed???

[@never_give_up90]

Thanks :) It wasn't what you showed but I was able to find the issue while doing everything you said. The water wasn't going into the filter area because the flaps got stuck even after filter was cleaned. So I washed everything and changed the filter just for the hack if it cause we had 3 more. After washing the flaps, they were good again. Without this I couldn't have figured it out. My man though the pump broke lol and was ready to trash it. I don't throw away money, not even if it's a "cheap" hot tub. It was a cheap easy fast fix. Thanks again.

[@FamilyDIY]

Glad the video was able to help and didn't end up throwing out a perfectly good spa

[@larrywatts8337]

What do you mean by the flaps?

[@never_give_up90]

@@larrywatts8337 rubber flaps that let water through to the filter. If they are not clean, they stick and prevent water from getting in.

[@davidkillian8927]

@@never_give_up90 how do you clean these flaps?

[@never_give_up90]

@@davidkillian8927 I used brush and mild soap.

[@ghostsnglam]

Mine throws the code only when I turn on the heat. Any suggestions?

[@Ytp-u9i]

Mine too, did you find any solution?

[@angieredpillsaustralia1751]

Mine does that too.. just the heat and filter button ?

[@Ytp-u9i]

@@angieredpillsaustralia1751 Try to backwash the pump and if it won’t help check impeller.

[@patrickkerbyson3422]

Mine does the same thing anybody have the fix ?

[@Uniquemomentstravelandmore]

So we just got our spa about a month ago and I just got that error and it was beeping and I didn’t know what to do !! so thank you for your video!!!!

[@FamilyDIY]

You are most welcome. It is one of the most common error codes.

[@artalli7170]

Just a note to people in the country with the red clay everywhere... our water looks clear and beautiful, but this filter gets FULL of mineral and red dust EVERY DAY. YES EVERY DAY. It's not broken. Unplug it, clean it out well, shake out the air bubbles as you go to screw it back on, then plug it back in. Country life for ya.

[@ericasporton667]

This totally helped me thank you so much!! I bought my spa second hand so I didnt get any instructions etc with it. It’s been the best thing I’ve ever bought, it’s a Helsinki laz-y-spa with the exact same pump, and yesterday it started beeping with this error and I had no clue what it was or how to fix it 🤷🏼‍♀️. And my little 6 month old granddaughter LOVES her Nannie’s spa with the bubbles so I was so worried the pump was broken, but I’ve now just taken the filter off and it was filthy so I’ve put a new one in it and it’s working perfectly again!! I also didn’t know you’re supposed to clean it daily, so I’ll make sure I do this now too, because I honestly just love it sooooo much and want to make sure it stays working really well ☺️ Great video, so thank you!!! 🙏🏼🙏🏼🙏🏼

[@cassandragreene5182]

Just so you know you can go online and print the instruction booklet for your Spa using the manufacturer name and model name.

[@timothylocke6242]

Love the dinosaur 🦕 noises in the background!

[@FamilyDIY]

Roar!! 🤣

[@andrewmullen4003]

Thanks for the tip about using the hose to flush out the heater pump, my filters when I have the E02 code are cleaner coming out than yours going in, so it maybe not the filter at fault. Though to update this didn't work either, had same fault again today, getting fed up with this same fault every 24 hrs.

[@FamilyDIY]

I have had to do that a couple of times. Really helps!

[@oscarteran7734]

Another commenter says it could be an air bubble (I have the same issue with a clean filter like you): Cleaning the filter doesn't work all the time. Even a new filter is not a guarantee. I've found that upon startup, an air bubble (in the pump, I believe) will throw an E-02 code. Taking both the filter and the chlorine/bromine tablet holder off and turning it back on for about 10 seconds pushes that air bubble right out. Then, just put the filter and tablet holder back on. Works every time for me.

[@dwaynetempest3433]

same here !

[@Cassidy_1983]

This didn’t work for me. It works fine when I run just the bubble but As soon as I hit the filter or heater button I get the e02’code again. Any other ideas?

[@patriciagallacher2905]

@Kittenwolf before connecting the filter to the spa give it a shake under the water to get air bubbles out.

[@caseyjones566]

There is a spa filter cleaner solution comes in a spray bottle really enhances the cleanup

[@kristen7948]

Thank you so much! Just had this error here in Australia

[@good2mac]

May need to do the hose thing - new filter on and still giving us the EO2 error. so bummed!!

[@jackburton4892]

I know this is a year later, but did y'all get rid of the error?

[@FrankPipitone-dl7ss]

Great video and great advice! Thank you for posting!

[@bobod346]

Perfect thanks man fixed in less then 5 mins you rock!!

[@FamilyDIY]

Awesome. Glad to hear it!

[@outofthemusicbox]

Thank you for this video. We only just received ours this week. Could the filter be this dirty already?

[@FamilyDIY]

Yea, the filter can get dirty pretty quickly depending on useage.

[@outofthemusicbox]

@Family DIY thank you for the fix! It was quick and easy. And yes, the filter was pretty dirty after only a week up and running. Now, to work on maintaining temperature... Thanks!

[@sageoliver8526]

Yep it worked…i had a clean filter, but the bromine tablets were too packed in I guess..I rinsed the filter anyway and emptied the old bromine tablets..also ran the bubbler a minute..maybe it needed to burp? Anyway after trying five electrical plug ins to no avail, your video fixed it!

[@BarryDMoss]

I did it & it worked like a Champ!

[@enmodo]

I had the E02 error on a brand new spa that had been running just 3 days. I initially thought it was a low water issue. Nope. Then I cleaned the filter - it was a little dirty, nothing like yours but it still gave an error. I verified it would start without the filter attached so I knew it was the filter. What I found was the rubber one way flaps inside the filter seemed slimy. So I hosed them off until they were squeaky clean and verified at sucking on the intake of the filter would open those flap values and let air through. After that I ran the pump without the filter and then slow screwed the filter on. This time it worked and water flows fine again. Not 100% sure if cleaning the flaps worked - I see someone below mentioned an air bubble in the system could be the cause - but I think it didn't hurt.

[@paulb9769]

I have no heat and no errors. All sensors are good and so are the heaters any ideas?

[@LeaMarchesseault]

Omg thank you was in my room watching tt and herd that beeping sound it was 2 am so the only one up was my dad we just got it thank you so much

[@Obiter3]

Getting E02 with a new filter, so gonna try that hose thing tomorrow 👍

[@xximjdxx]

Ugh. Thank you. Spraying a hose into the actual pump helped.

[@FamilyDIY]

Glad to have been some help

[@bubbblesgoesmeow9179]

THX KING! Saves my life😻😻 you’re the best!!!

[@playboycharmed1]

Thank you! Worked like a charm.

[@AngelaDorn-m4e]

Tried all these suggestions but still didn’t work I don’t even hear the pump running any other ideas? Thank u

[@reillysimons8518]

Is the control panel weatherproof? As in, does it need to be face down if it's raining, or can it be left in the upright position. Thanks!

[@amygriffiths9113]

Any chance chemicals could cause a flow problem with the filter? Mine was running fine and had cleaned the filter a few days prior. Added some pH up and E02 came on a little later. After resetting it a couple of times I cleaned the filter and it ran fine, then next day I added some shock and the E02 code again. Reset a couple of times then finally cleaned the filter again and it's running again. It's 7 degrees and snowing here so I'm panicked that it will freeze in the middle of the night. Thanks!

[@AlishaBeck-h7t]

Ours is giving us this code upon inflating it. So it doesn’t make sense that it’s the filter. Any other ideas as to why it’s occurring when it’s inflating before water is involved?

[@lynseyhubbard6316]

Thank you so much for this video!

[@debbieionna3198]

I am 28 days out of warranty. My bubbler does no work even after unplugging and resetting. My side walls have started to collapse. I called Bestway and after a 45 minute hold i was told to stick a hose in the bubbler to loosen any blockage. I cannot find where to stick the hose in for the bubbler. Help! I have emptied the tub. Thanks for your help

[@FamilyDIY]

The bubbler hole is the largest port on the side of the spa. You side walls are collapsing because you need to refill your spa with air, if the bumps air jet is not working, if you have a shop vac or other item that blows air, left blower, press it up again in refill area, it should work.

[@debbieionna3198]

Thanks for helping. I emptied the wayer out, disconnected pump from ac outlet and disconnected all pump hoses. I will refill air to blow up walls tomorrow and see if i can dislodge any debris from the bubbler. Thanks again!

[@kaseycable5615]

Question** our new spa seems to pull water into the heater in a way that fills up the tube, but the outlet tube pushing water back into the spa is only about half full. Is this an issue?

[@Sarahdawna]

Clean INSIDE the tube that the filter goes over, with a stick or something- not your pinky, like i did (although it worked, i don't want anyone to get hurt). Anyway, worked like a charm, and fixed the water flow error message

[@valerierichardson873]

Changing the filter worked, thank you!

[@FamilyDIY]

awesome! glad it worked

[@jennkelly4027]

Thank you so much for this great video! Unrelated to the filter, I noticed that you had this hooked up to an extension cord. We did the same thing as the GFCI box won't fit in our recessed outlet fitting. Before I have anything rewired, have you had any issues with the extension cord? Do you recommend any special type? Thanks so much!

[@FamilyDIY]

Sorry, I have no recommendations other than I am using a very long one I got from homedepot that I use for Christmas lights in December when my spa is off.

[@jennpeterson8690]

@@FamilyDIY perfect! Have you had any issue with that situation? Do you use any kind of waterproofing around the spa plug / extension cord connection?

[@debluluby3024]

Thank you soo much!! Worked like a charm!

[@Pollydoidle]

My spa doing this , done everything you said but still not working, rest button doe#nt work , won’t turn on and off only at the plug, so criss only brought it br@nd new last year in summer sKe was only used a month then packed away fir winter

[@peadarbradaigh8612]

Awesome. Problem solved, thank you!!

[@FrakYourself]

Very helpful. Thank you

[@FamilyDIY]

You are welcome

[@naseemazadi94]

Hello . My filter won't screw back on. I'm not sure why.

[@nrnoble]

I have found the inflatable cover that come with the SPA does not do a very good job of keeping dirt and other small debris out the hot tube. I bought a durable weather proof tarp. to cover the inflatable cover. The inflatable cover is still needed to help trap the heat because the tarp is just to keep out derbre. A $50 - $100 weather proof tarp will keep the hot tub much cleaner and reduce pump issues.

[@lifesinsanity4432]

Thank you. Quick and to the point. Look forward to checking out your other videos.

[@FamilyDIY]

You are most welcome!

[@jdawgfps9646]

Just bought a GoPlus inflatable hot tub it was working for almost a week then it stopped and started Beeping & flash “HA” on the Screen I contacted them and they emailed me troubleshooting directions & I looked everything over and everything seems fine but the pump keeps beeping and flashing “HA” just don’t know what to do…. 🤦‍♂️

[@elbybaby911]

Can you shoot water into all 3 of those connections on the pump? My heater stopped working after finding my kids ate eggs in the tub.

[@nyhost101]

Eww...eggs in the tub...lol. yes all 3 holes please

[@willnavin8784]

Thanks! Gonna go give it a try.

[@vincenttucker9151]

i went over the design of it and ended up drilling a hole in the plastic screw end for the filter housing. solved the continuous error.

[@CalvinDabrowski]

Don’t expect your filter to work after that. Won’t filter when going through the screw hole. Bypasses it.

[@f.fierro1256]

do you have a video on how to fix the heating element? mine stopped heating above 95

[@FamilyDIY]

Haven't had that problem yet so no.

[@shansenbio]

Where does one get the civers to put on the input and output valve openings inside tub if I need to disconnect pump? What are those parts actually called so I can order. Thanks in advance

[@jeffjones5432]

Can you tell me where my Hydro jets and air jets will not run together on my brand new Santorini tub, thank you

[@frostray7872]

Fixed it straight away but I just used a new filter I will save the other one and wash it when I have some time. Thanks

[@FamilyDIY]

glad to help

[@cybercab]

Mine does that and won’t let me do the initial inflate on a new unit.

[@nocapper]

does anyone know the size of the in/out water fittings from the pump? I want to build a descaler for the pump to go to a bucket and want to connect the pump to the bucket of course.

[@thomasz9226]

My spa is 4 days old and used twice. Tried cleaning the filter, unplugged the unit and put it back on. Worked normal for about 20 minutes and started again. I find it hard to believe it would be clogged lines or build up already. If so, who would want to do this every few days? We'll see

[@FamilyDIY]

No need to unplug, just swap out a fresh one, clean the dirty, repeat.

[@amymatusky4857]

I have a Saluspa S100105 which replacement filters do I purchase?

[@FamilyDIY]

I think they are all the same. Try googling it.

[@stevecrawford333]

what is the plastic above the chem connect and filter at the top?

[@matthankins6074]

I’d like to know as well!

[@brucegreig1347]

@@matthankins6074 Just a simple overflow for excess water. Nothing to do with any E0-2 error

[@amyrenee9165]

That's all fine and dandy but I am just trying to blow it up. Of course there's no water flowing so why this error code?

[@annmariemanning7902]

Every time we get this code, I change the filter and it works no problem. This time I have changed the filter, I have disconnected the pump and I have flushed through all of the hoses and still get the code. When I press the jets it works fine but as soon as I press the heat or the filter button the code shows up again. Any tips? Thanks in advance.

[@LettiesLife]

So wait? If I have a whole new motor, I don’t have to drain the tub?? I am trying to think if I have caps to inside fixings

[@RachelDiBuono]

Help! I've put the drain stoppers on both tubes to disconnect the pump. But the C pipe is 100% pouring water out, as though there is no cap on the inside. Can someone tell me what the problem is and how to fix this?

[@dennisthompson2170]

I just hooked my spa after having it down for 3 months. I filled it up and set the controls and left it to heat overnight. Came out the next morning and half of the water was gone but it was not wet around the spa. It was almost like it evaporated with the top secured, happened twice. Any advice?

[@FamilyDIY]

That is really weird. Must be some type of leak

[@dennisthompson2170]

@@FamilyDIY thats what I thought but the area around it is perfectly dry

[@FamilyDIY]

hmm. I am not sure. when you are heating it, is the lid on?

[@patriciagallacher2905]

@@dennisthompson2170 water could be going into the inflatable area? Did you figure it out?

[@dennisthompson2170]

@@patriciagallacher2905 It is kind of working if I refill about a foot every 3 days. I am going to have to take it apart. It is leaking near the pump but does not appear to be putting water back into the unit. THanks.

[@ericasilvestri3038]

So in the past changing the filter hs worked.... I did that and pushed water through with my hose and still getting the error 2 code.... what should I do next????

[@deadmeet-vy7fl]

I was going to drain mine and return it to Costco for a new one. My last pump got too much full sun and gave out. I cleaned the filter and several hrs later got the code again. I will try getting out the bubbles. I use a floating chlorine dispenser

[@chuckparkins8267]

I have an E03 error code. From what I understand its a "temperature thing" ( it's too cold). It went off without me knowing, maybe a blown fuse? I hadn't used it in a week or so. How do I disconnect the tub from the motor without it draining the tub? Thanks!

[@FamilyDIY]

Just add the plastic covers on the water ports, no water will come out. If you lost them, just put some plastic wrap over and the water pressure will hold them in place

[@danphillips6167]

I'm just setting up ours. Got an E-02 before I even got it blew up completely. It cold here 30 degrees Fahrenheit

[@FamilyDIY]

There is a flapper that is part of the water flow sensor. Might be stuck in the cold

[@benjaminignaciojarasalas4930]

Hola, mi calefactor no calienta, presiono el boton para calentar el ague y no enciende luz, el resto del panel funciona bien, que puedo hacer? Necesito ayuda

[@TheBrooklynfoo]

what happens if the filter doesnt even turn on at all then the E02 error comes on? Like it doesnt even attempt to start up? Is this more an electrical issue>?

[@brendanwoodey7961]

I'm having this issue as well. I turn it on, I can hear a relay click, then it throws the error code.

[@jonzey75]

Why would the GFCI cord keep tripping.

[@FamilyDIY]

Because it is sitting next to some mushrooms 🍄

[@melissacapps4291]

I've tried clearing the filter and water is moving like it should and it keeps giving me the Eo2 error could it be the temperature Guage

[@jessicab7233]

Our problem is we start the spa everything’s working the bubbles the heat etc. and then it turns off within 30 seconds to a minute do you know anything or any suggestions anything would help

[@Sarahdawna]

Hey, I had the same issue. I had to clean inside the tube that the filter goes over.

[@beverlyskaggs7103]

If my hot tub is low on water. Any it shuts off. It does shut off by its self right.

[@kerryheavingham1272]

Hi we have a new one.we have the eara come up befor we even blow the thing up iv tried reset both buttons can any one help as can not get it to go on

[@FamilyDIY]

Try shooting water through the water inlet with a hose. There might be a blockage.

[@LettiesLife]

Very helpful! 🫶🏼🦋💜

[@jethrothecat812]

Thanks you helped me alot

[@rebecca88088]

Mine just stopped working. No error message at all: it just turned off and is showing the temp and nothing else. when i plug in again all the lights light up for a second but then go off and nothing will start. Changed filter but still doing nothing. HELP!!??

[@anthonyfuqboi8211]

Try holding down the power button for like 8 seconds

[@carriemcneal9357]

I am so frustrated because my spa is very new...I have only used it myself 2 times. Each time it is used after use is finished a sh0rt time the error code starts up. I have cleaned (the almost new} filter and also tried a new one. I have taken them off and run the motor a bit before replacing them, I have swished them in the water before replacing them. Nothing seems to work. I would like to be able to use this spa but can't get it up to temp because the error code keeps going off and I have to actually unplug the spa again in order to get the code to stop. There is never enough time to get it heated up to temp Please help! It seems like this is a defect that needs to be cared for by the company if so many people are having issues with it.

[@FamilyDIY]

EO2 is a water flower error. It happens anytime the flow slows down, blocked filter. This happens a lot after usage and the filters need to be cleaned / rotated. A simple hose down should take care of it. Also brush the inlet without the filter. Don't run the pump without the filter, this could clog the pump. Try removing pump from the spa and spry you hose into the water inlet and outlet. This will remove any derby

[@outofthemusicbox]

Hi thanks so much for your comment about the spa. What you described is already what ours is doing after only one week. Did you keep yours or return it? I'm already leaning towards return, sadly. Hope you can give me a tip. Thanks so much!

[@sierradanielson1516]

We haven’t even set ours up yet, not blown up, but plugged it in to make sure the power wouldn’t trip a breaker. After we plug in, the heat and water button glow and then it throws this error. Any suggestions?

[@wiseartmusic5979]

It’s throwing the error cause no water is flowing through it. Setup your hot tub lol

[@matthanson4720]

Mine throw the EO2 code with set up. Just trying to inflate the spa. So there's no water. Realllly confused

[@FamilyDIY]

Weird. Are all the caps off? Maybe some packaging got stuck in a tube.

[@ScottMarionMCS]

Same here…worked fine last year, stored in the basement and now E02 as soon as I turn it on to fill the air….

[@imdeplorable2241]

Set mine back up 3 weeks ago. Immediately got an E02 code. Cleaned filters --- same code. New filters --- no help. Pulled filters and chlorine/bromine dispenser off, turned on. In about 10 seconds a large air bubble shot out off the discharge. Replaced filters and dispenser. Problem solved.👍 Ordering some new impellers and flow sensors for the future to limit down time. KZbin videos like this are immensely helpful. Thank you.

[@austinaelkins]

E05? Any ideas?

[@randyfonk575]

Eo4 code now. I’ve fixed every other code.. now this one! Can’t clear it?

[@kristenabbate9446]

Has anyone found a heavy rain storm could cause the error code?? I keep unplugging and the code happens again and again. The tub is only 5 days old.

[@mfdalessio]

Mine throws the code when I use a filter. Works fine when I don’t have a filter on it. Even new filters throw the code.

[@alisagumm8547]

It was the filter for me. Once I changed it, the problem was solved. 😂

[@MarielaPereyra-t1z]

Thank youuuu!!! ❤🎉

[@trevorsartin8095]

I got this error the other day and replaced the filter to resolve the error code. However, now the heat does not work although I have water flow. Any thoughts?

[@cjw1az]

Basic question: did you check that you turned the heat back on? I did this once. I only turned on the water pump but not the heater.

[@eddyacevedo5089]

Anyone has had the problem of the no air for spa effect??? help!

[@lorileiescalante9645]

I have EO3 code. What's is that one?

[@anonimous3806]

Helpful thanks.

[@FamilyDIY]

Thank you very much. Glad to help!