Beta FPV PAVO 20!! 4S Custom Build!!

[@SOKOL60A]

Лично мне нравятся такие Плавные перемещения. )) Если нужен фристайл, то я бы выбрал -1S и Emax Tinyhawk Project Mockingbird. Personally, I like such Smooth movements. )) If you need freestyle, then I would choose -1S and Emax Tinyhawk Project Mockingbird.👍👋

[@slowerlowerrc]

Tinyhawks are nice!! Thanks for the comment!!

[@FCSTACK]

nice build🎉

[@slowerlowerrc]

Thanks!!

[@ocdraridrogonel]

This is why I don't like the Pavo cause the battery is on the bottom. This is why I chose the gofilm 20 compared to the Pavo as well the esc allows for 4(s) 850 1000 mAH...

[@GR33ZY.A1]

Try 1204 5000kv 👌🏼💯🎯

[@vtv23]

Could you share your rates? Would love to fly it indoors. Thanks!

[@slowerlowerrc]

It's different with every build but similar.Save backup, Update FC and escs, load backup. Then cutback motor output to around 50%. Add at least 50% expo on evrything including throttle. Now adjust idle in motors tab until it lifts around 25% throttle. This is the easiest way to explain. You can try a cinewhoop preset but most of them are very slow and hard to fly. My advise is to keep moving at a steady rate when flying indoors and try to keep moving especially in hallways. Good Luck!!

[@SOKOL60A]

Отлично!! Дружище, я то - же хочу сделать подобное в аналоге. И мне нравится твой выбор комплектующих, я полностью с тобой соглашаюсь только Камера cadex ANT или беззубик foxeer. Пока еще не понял зачем тебе BEC ?? и передатчик буду ставить OPEN VTX 003. И вот Вопрос - откуда взять готовые PID?? С благодарностью приму любую помощь. !Great!! My friend, I also want to do something similar in analogue. And I like your choice of components, I completely agree with you, only the cadex ANT camera or the foxeer toothless. I still don’t understand why you need BEC?? and I will install the transmitter OPEN VTX 003. And here is the Question - where can I get ready-made PIDs?? I will gratefully accept any help😛🥺

[@slowerlowerrc]

With analog if you get static or noise in the system when powering vtx from fc it will clean it up and filter power using a BEC. I wouldn't mess with the pids on cinewhoop. There are presets in betaflight but they are extremely slow. Power back your motors to 50 to 60 percent. Turn up your idle speed so you hover around 20 percent. Slow down your rates.Turn up expo on rates on all axis including throttle expo. This will smooth everything down. It takes some tweaking and patience but slow down your rates, add expo and you should get the results your looking for. Thanks for the comment!!

[@SOKOL60A]

​@@slowerlowerrc Мне идет контроллер для сборки pavo в аналоге -Happymodel CrazyF411 ELRS AIO 4 в 1 F411 . Досмотрев ролик понял, BEC нужен для питания -runcam thumb pro. Выбор компонентов и сборка дело не самое сложное. PID - тюнинг куда важнее и труднее!!. Еще хочу попробовать заменить ctm-32 F.C. на ARTERU - полетными контроллерами серии AT32 . У него тактовая частота выше F7 и производительность больше. Но там трудность с драйверами и нужно B.F. версии 10-10. Как Вы пробовали подобную замену?? I need a controller for assembling pavo in analogue - Happymodel CrazyF411 ELRS AIO 4 in 1 F411. After watching the video I realized that BEC is needed for power supply -runcam thumb pro. Selecting components and assembling is not the most difficult thing. PID - tuning is much more important and more difficult!!. I also want to try replacing the ctm-32 F.C. on ARTERU - AT32 series flight controllers. It has a clock speed higher than F7 and more performance. But there is a difficulty with drivers and you need B.F. versions 10-10. How have you tried such a replacement??😅