BetaFPV Pavo25 Cinewhoop Build, and review

[@MCsCreations]

Awesome build and flying, Dan! 😃 Thanks for the review! Stay safe there with your family! 🖖😊

[@josefdahari]

Excellent. I probably will convert my 95x to the pavo25 as well

[@divingfalconfpv4602]

Oh didn't think of that. I was going to buy bnf 🤣

[@josefdahari]

@@divingfalconfpv4602 literally the perfect thing drop your guts onto the frame !🤟

[@Flow_FPV]

Thanks ! :D

[@GatAppTechnologies]

Does a Walksnail VTX fit in there? Seems to be around the same size as the VTX you put in there but wanted to see if you knew.

[@divingfalconfpv4602]

Is this less front heavy than 95x v3? Can it fly hero10 bones? My 95x v3 seems too front heavy. Can't push battery back. Flies terrible with it. HD cam on this still looks far forward over front motors. Not sure how far back u can push battery to get 50/50 .. looking at cinelog25 too HD cam looks further back Think I'm change my old 95x v3 to 1207 motors to test 5blades & more weight but I know my old rcinpower 1207 ran hot but they never burnt out. Burnt my finger but kept working Also looked at mamba 1206 in 6s kV 😳😍

[@Roundawg]

Nice vid. Will the Vista fit if it is not naked? Also, what other FC and motors you recommend? Do we have to use 4500kv or would 4600kv woek.as well?

[@TweetFPV]

A normal visita will fit just fine. 4600kv would be just fine as well. As far as aios go I would stick with something that has a USB port that comes out the side and not the top.

[@Roundawg]

@@TweetFPV Thank you for your replay. Do you think the Diatone Mamba F411 25A BLHeli_S 2-4S AIO would be a good fit. I've seen where a 90deg adapter.might be needed.

[@TweetFPV]

That should work just fine.

[@LNRWLF]

Hello, I have built this exactly as you did but I’m having trouble in where my Express LRS is connected to my radio (X9D) but I don’t have any stick inputs in Betaflight. I’m using the Beta FPV rx with the tower antenna. I have switched out 3 different RXs and I still have the same problem.

[@TweetFPV]

Are you getting any telemetry on your radios screen (signal bars) if you are then your betaflight configuration or your wiring from the receiver to flight controller has errors in it.

[@LNRWLF]

Yes it does have telemetry. By the way I’ve came across something i didn’t see in the video about this aio FC regarding the Beta FPV diagram in which it says you need to solder 2 pads together for the CRSF (Lrs) Receiver. Did you solder those or just leave them as they are?

[@TweetFPV]

I didn't have any solder bridge pads like that on the aio I used. So if you have telemetry then your receiver and transmitter are bound and your issues are with either how you wired the receiver to the flight controller or in your betaflight setup. A LOT of people mess up the connections from the rx to fc. Remember you need to run for rx to tx and tx to rx from the receiver to which ever uart you are using. Then you need to select that uart as serial rx in the bf ports tab. Then in the receiver tab you need to select serial based receiver and crsf as the protocol.

[@sergiopolonia]

Hey thanks for the great content. I have a question I just build a pavo25. All modes are set. I am able to arm but motors just spin any idea what’s going wrong

[@TweetFPV]

Not a lot of info to go off of here.. My guess is your props are on upside down or your motors are spinning the wrong direction causing thrust to be In the wrong direction.

[@sergiopolonia]

@@TweetFPV I arm the quad but all I get is spinning motors is does not come off the ground. My props are spinning as followed 4 and 1 clockwise 3 and 2 counter. Any ideas

[@TweetFPV]

Perhaps your props are on upside down and generating thrust in the wrong direction. Or perhaps you have too big of a battery/payload for it to actually get airborne.

[@thfpv4974]

Is that video from your goggles?

[@TweetFPV]

No, it's from a naked gopro hero6

[@DougOrDouglas]

where is the analog aio information for this board?

[@TweetFPV]

Analog aio? This aio is analog or digital. Depends on what system you connect to it.

[@DougOrDouglas]

@@TweetFPV I was able to find someone who wired it analog, i was hoping to use the DJI stuff to make it plug in play for analog,i but i have to hardware to the pads

[@TweetFPV]

The pinout is on betafpv.com. The connections you need to make for analog are all solder pads and not plugs.

[@DougOrDouglas]

@@TweetFPV yeah found that info, you think that crossfire needs to be solder on pads too, or that could use the plugs?

[@TweetFPV]

Yes crsf could be on a plug.