i bought a 01 a4 b5 in pelican blue about 6 months ago, looking to do similar power numbers. This is a sick build, cosmetically and motor wise. Love it man!
@zed00018 ай бұрын
Just found your channel, keep the content going. Love it.
@aypx89577 ай бұрын
That color is sick bro!
@tonyregalado72816 ай бұрын
Nice build! What internals are you running? I'm fairly new to the Audi world, but recently acquired a 2002 1.8T A4 Avant for dirt cheap that needs an engine. Can you give me some advice on what's needed for a 300-350whp build? I have the 06A block and I'm considering stroking it to a 2.0 with the fsi crank. I'm familiar with Subarus and know what's needed for x amount of power, but a complete noob when it comes to Audi, lol. I know the rods are basically a must, but what about the stock pistons? Can I make 350whp with just rods and supporting mods, or do I need aftermarket pistons as well? I'm trying to do this for as cheap as possible, so the more S4/RS4/R8 parts I can use, the better. One last question, do you know which stock 1.8ts came with forged pistons? Thanks in advance!
@BoostedBucci6 ай бұрын
Thanks! I have ebay H beam rods and brand new stock AEB pistons, the AEB motors (97 and 98) came with forged pistons stock which are good up to 600hp or so. last weak link is the exhaust valves, upgrade to inconel and you are good to go. All you really need for 300-350whp is a gtx2867 size turbo, I would go with a g25-550 from pulsar you'll have very good spool with 20+psi around 3500rpm. So source a turbo manifold, turbo, intercooler, Rods/piston,fueling upgrades, and exhaust upgrades (mainly downpipe) and you'll be at a happy 350whp
@BoostedBucci6 ай бұрын
My parts 058 block 1.8 stock bore, AEB head ported aeb head w/ upgraded springs/retainers and inconel exh valves maxspeeding rods with stock pistons King bearings 630cc deka injectors w/ bosch 044 fuel pump cast Spa turbo exh manifold pulsar g25-660 with t/51r mod and Tial QR50mm recirculated BOV Vsracing 44mm EWG 29"x11"x3" center feed intercooler custom 3" turbo back exhaust with borla xr-1 muffler vogtland coilover shocks w/ swift springs adjustable upper/lower control arms front and rear 18x9.5 wheels w/ federal rs-rr 255/35/18
@jamilahmed9799 ай бұрын
Again nice build! Keep the vids coming.
@aShamelessHigh9 ай бұрын
People over here hatin' on the gold and im here like, damn i wanna do that to my intake 😅....
@Honzikponzik8 ай бұрын
Haha me too
@LucaTrauner3 ай бұрын
Sick Build. I saw this car on IG and now here on KZbin. Is it quattro or fwd? Looping forward to more Videos. Keep it up 💯
@BoostedBucci9 ай бұрын
Driving clips start at 5:15 in case anybody missed it
@jamilahmed9799 ай бұрын
Nice build! If I were u I would continue to add more weight saving mods in the front of the car. Capitalize on that and you'll have a nimble handling quattro machine.
@WidgeTheWiz6 ай бұрын
Great car! Inspires me to continue working on my B5. Does your ESP system still work?
@BoostedBucci6 ай бұрын
It's a 98 so I don't think they came with ESP, but I'm not sure because my ABS has never worked since I got the car
@Ewan3009 ай бұрын
Dude you gotta black the whole car out, would look insane
@theyrealltaken38 ай бұрын
Pretty car and beautiful color. Please don't do black. Black has been done to death. Boring af. Hides all the lines of the car.
@williambarth68406 ай бұрын
Damn that things a little rocket
@hell_catt59157 ай бұрын
Hello, i have a question. What transmission do you have in you car, is it an 01E? What is the reference of the one you have installed?
@BoostedBucci7 ай бұрын
Nah the 01E 6 spd came in the S4, i might eventually do the swap when this transmission blows. I have the O1A 5 spd
@Bresoto7 ай бұрын
Great Project, tell me, do you change something at the RETURN OIL LINE of the turbo? the cárter.
@BoostedBucci7 ай бұрын
Yes the oil and water lines had to be custom made, the turbos oil return line is custom welded solid steel down past the exhaust manifold
@Bresoto7 ай бұрын
@@BoostedBucci do you have whatsapp? maybe you can help me with the problem i have with my A4 big Turbo.
@BoostedBucci7 ай бұрын
@@Bresoto sure maybe i can help, what is ur whatsapp
@pluto47421Ай бұрын
Did you have to get adapters for the r8 coil packs and is there anything I would have to upgrade for that or no
@BoostedBucciАй бұрын
Yeah I re-wired the plugs to the r8 style plug, before that I used an adapter harness. Nothing else you need to upgrade but it allows you to increase your spark plug gap
@unstable-81699 ай бұрын
such a sick build dude, personally i find the gold a bit tacky but nonetheless still beautiful build
@BoostedBucci9 ай бұрын
Its heat shielding but I'm getting over the gold too, gonna clean it up and switch out
@unstable-81699 ай бұрын
@@BoostedBucci more like heat reflector but yeah fair enough I'm letting u cook
@knolez15468 ай бұрын
Nice quattro. How did I notice? Engine placement. It's longitudinal.
@andrevagante8 ай бұрын
the engine is longitudinal on the fwd one aswell.
@115Jester7 ай бұрын
The audi tt quattro is horizontal, awd doesnt always mean it has to be longitudinal, there are many awd jdms that also have the engine horizontally, in particular evos.
@melv8895 күн бұрын
B5 Plattform is always longitudinal. But he also said he has upgraded rear upper control arms.. so it's a quattro axle which he is talking about
@thatnoobguy61468 ай бұрын
Could you make a video about how you routed your vacuum lines and wastegate set up? I am STRUGGLING on my a4 build with the lines
@BoostedBucci8 ай бұрын
There's not very many lines because I did a full evap/pcv delete and dont use the n75
@S4POfficial8 ай бұрын
I’m also having that issue, except I swapped an AWP motor in and I cannot get it to run for long at all thing runs awesome for a about 30 seconds to a minute and then starts bogging down and stalls.
@BoostedBucci8 ай бұрын
For my WG top port open, side ports capped except 1 that goes to the boost controller and out of the boost controller into the boost pipe outlet of the turbo for vacuum/boost reference. Diverter valve reference comes from the intake manifold. Evap is blocked off and PCV goes to a vented oil catch can. Thats it
@codylyles543 ай бұрын
What size overfenders did you get?
@BoostedBucci3 ай бұрын
2.5" width
@A_Vw_Garage.8 ай бұрын
Where’d you get the strut bar from? I’ve been trying to find a good one for my b5 Passat but no luck.
@BoostedBucci8 ай бұрын
I got lucky and found someone selling it on audizine forums
@raudii0B58 ай бұрын
Nice build! Was wondering if you could put a link to the over fenders you got.
@BoostedBucci8 ай бұрын
www.driftshop.com/fender-flares-70mm.html
@1.8_hoopt8 ай бұрын
Been looking to do a light weight battery did you need to use a custom bracket or anything to hold it down?
@BoostedBucci8 ай бұрын
I used a pc680 aluminum hold down bracket and rivnutted it to the firewall so its easily removable
@1.8_hoopt8 ай бұрын
Right on!
@projectjunkies84632 ай бұрын
What needed to be done to get the car me7 swap I got 99 ?
@BoostedBucci2 ай бұрын
its not me7 its still me5 narrowband
@pluto47421Ай бұрын
What transmission u running
@BoostedBucciАй бұрын
stock 01A 5 speed AWD
@mostwanted6379Ай бұрын
awd or fwd?
@BoostedBucciАй бұрын
AWD
@keebler91411Ай бұрын
Holy shit I wanna do this to by lil b5 too 🤣preferably with a hood dump lol
@sametball347 ай бұрын
Hey my friend, can u write about parts?
@BoostedBucci7 ай бұрын
058 block 1.8 stock bore, AEB head ported aeb head w/ upgraded springs/retainers and inconel exh valves maxspeeding rods with stock pistons King bearings 630cc deka injectors w/ bosch 044 fuel pump cast Spa turbo exh manifold pulsar g25-660 with t/51r mod and Tial QR50mm recirculated BOV Vsracing 44mm EWG 29"x11"x3" center feed intercooler custom 3" turbo back exhaust with borla xr-1 muffler vogtland coilover shocks w/ swift springs adjustable upper/lower control arms front and rear 18x9.5 wheels w/ federal rs-rr 255/35/18
@sametball347 ай бұрын
@@BoostedBucci Hi again my friend my project; As you know, there will be a 2.7 T engine for the A4 B5. They used this engine in the B5 S4 models before. I expect it to be around 800-1000 hp. I'm currently using an e36 bmw m3.
@BoostedBucci7 ай бұрын
@@sametball34 That's gonna be a really cool car bro!
@samdzus24276 ай бұрын
@@BoostedBucciI’m wondering what spring weight you went with on the blow off valve and the waste gate?
@BoostedBucci6 ай бұрын
@@samdzus2427 BOV spring is 9lb since my car idles at -17in vacuum, 10lb would work too. WG spring I don't think I changed from the 12lb spring that came with it
@MrThobias114 ай бұрын
what ecu do you have ? :)
@BoostedBucci4 ай бұрын
Stock narrowband ME5.9 ecu tuned by united motorsport
@TAC0BUS8 ай бұрын
Is It QUATTRO?
@BoostedBucci8 ай бұрын
Yes
@mariusmisiavicius10119 ай бұрын
Maybe you can add a link where to buy a spoiler?
@BoostedBucci9 ай бұрын
this is the one on my car but I changed the corners a bit. www.ebay.com/itm/DUCKBILL-495F-Type-PUF-Rear-Trunk-Spoiler-Wing-Fits-1995-2001-Audi-A4-B5-Sedan/273905203612 This is the same style smaller and not as tall www.ebay.com/itm/122227561154?itmprp=cksum%3A122227561154f1ca7b718d0748bc8af342e7eb501551%7Cenc%3AAQAJAAABcLSVkHmTL63bebovD9RfpraPWbY9f4anjbziTIaEIOVXg2DWhVLks3Lfqff9vxxfjIh4XEXusIehlT2iEH8%252BCxXNySMxlDIQJ3g86%252Bx3AAIAq9gznqdGSR72ksP41kjzPN1reUbVsJuld0S4i4qXlQfTmkMeIJTCXTM8mLpr7ju2fMvruDu87ZX%252B4bShOvD%252B4ub%252B925XXQGyNe0rcia92UO77wqlxCAlxd%252FKZN0tX%252FWpGyKaBWF%252Fuon4Uh1WeVg3VXt5xDusfWzKQ4MIf0i0VCrDA9HrvyDCQg0luypMPNikUhqtUeGol9LhHI6H%252FcbMZhbDpvKOqyP5oGqHv1shKWCXTZKtH7MfymYIDY4D97TZ6dEtV4hnaibB7pU0WCI9w4Fbi31HzS5porynbxmovTm7nypJ4sdue1IdjnIvRRV7jUToEpdmh%252FpySEg3eHH6TK2GxLtqcfXZya5sSzn0j4J3QRYBH1hB3gZFEMj9Axrw%7Campid%3APL_CLK%7Cclp%3A4429486&itmmeta=01HSSPGSADKKD8QZ7EMY57MF2E
@JNAMOTORSPORTS6 ай бұрын
They used the gold in the F1 it indeed does work if its real and higher end
@gsrmam44898 ай бұрын
هل هذا المحرك طراز ADR
@BoostedBucci8 ай бұрын
it is AEB
@gsrmam44898 ай бұрын
هل يوجد طراز ADR تيربو موديل 2000
@BoostedBucci8 ай бұрын
@@gsrmam4489 لا يحتوي طراز محرك ADR على توربو
@NightRevv9 ай бұрын
HP?
@BoostedBucci9 ай бұрын
375+ish on 91 octane, 500+ on e85+meth
@zDrotex8 ай бұрын
bulit bottom? I want to put a k04 on my B6 A4 but i dont want to blow up my motor @@BoostedBucci
@BoostedBucci8 ай бұрын
@@zDrotex Yeah forged rods/pistons and race bearings . K04 can bend rods because theyre so torque spikey at low rpm, some people get away with it some people dont. If you're gonna do rods might a well do a gt2560rs anyways ;)