Remove HEADLIGHTS DODGE RAM

How to remove headlights without removing the grill!!!
Big thanks to corneileous from DODGE RAM FORUMS for telling me this. Hope this saves everyone some time when changing out front headlight bulbs.
Here is the updated video to this one.
• Remove HEADLIGHTS DODG...
in this video I show the L bracket holding the headlight in and go over other things you guys wanted to see more in depth.
Thanks for watching and your support!
I just started Instagram if you guys want to check it out....
www.instagram....
OLED Headlights
amzn.to/33IrXoe
DO NOT CLICK THIS!!! / bigdaddyshouse
Some of my links are Amazon affiliate links. Thank you for your support!
AlfaOBD App: amzn.to/2HFuNSt (You can also get it in the playstore)
OBDLink MX+: amzn.to/2S4Rv8w
PEDAL COMMANDER: amzn.to/3mW2yin
In today's world this has to be said.......
Disclaimer: Due to factors beyond the control of "I" or big daddy's house, I cannot guarantee against improper use or unauthorized modifications of this information. "I" big daddy's house assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. "I" big daddy's house recommend safe practices when working on vehicles and or with tools seen or implied in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not "I" big daddy's house. This video is for entertainment purposes only.

[@seanleverone7680]

I can’t figure out the “L Bracket” part

[@bigdaddyshouse]

Try watching this Sean. I go way into depth about it and show visuals. kzbin.info/www/bejne/hYXVdIV6drCApqs

[@michaelcampise5617]

Nothing to it Dont over think it Slide one way to lock into light slide other way to release. Up or down Once you remove the light you will see how it works

[@billmiller1584]

I'm NOT a mechanic, wasn't looking forward to this...it worked!! Did both lights in less than half an hour. Thanks to you and Cornelius!

[@bigdaddyshouse]

You're welcome sir. Thank you for watching.

[@kstamps2350]

@@bigdaddyshouse y77nn nnnnnn

[@kstamps2350]

Nn nn n n n. Nn nnn nnnnnnn nn nnn n. Nnnnnn. NNnn nn nnnnnn n. Nn nnnn. Nnn nn nnn n. Nnnn nn n

[@kstamps2350]

N nn nnnnnn

[@kstamps2350]

Nnnnn nnnn. Nnnk

[@shefner208]

This is dead on. By far the easiest way to change the headlights. The only thing I would add is on a 5500, once you release the clip in the fender well give the headlight a little push while your hand is in there. It made the headlight come right out vs having to pull so much from the fender side of the headlight. GREAT VIDEO!!

[@bigdaddyshouse]

Thanks man, glad you enjoyed it. And I appreciate the tit for the 5500!

[@billshultz1912]

Thanks, simple directions and saves buku time from removing unnecessary grill. For what it's worth, I removed the lower screw so it was easier to install the headlight assembly. Then I took some painters tape and taped the edge of the washer on the screw to my socket so it was easy to place the screw into the nut.

[@matty2000shoes]

Thanks brother. I have a 2019 ram classic. Your videos have helped me learn AlphaObd, install and set up the EVIC gauges. Activate turn signal DRL's. Enable factory alarm. And this weekend I'll be installing my led headlights with switchback turn signals. So I'm sure I'll be back watching again. Haha. 👍

[@raymondjohnson6196]

Thank you for the info. After taking my truck apart the first time to change the headlight bulbs in my 2020 Ram 3500 I decided to look for a KZbin of any ideas that could save me time and work. After watching your video I decided to go through the fender well access I saw on your video. I was able to reach through and changed my bulb in 5 min with only a flathead screwdriver. Thank you soooo much!!

[@mo-215]

SUPERB!!! WORKED perfectly on my 2019 classic. What a time saver!! Hilarious delivery too.

[@bigdaddyshouse]

Thanks brother! Glad it worked out for you. I appreciate you watching and your support.

[@praingmantis1]

I just want to thank you for this video. Popped the headlights housings out, replaced the bulbs and done. Easy Peasy! Thank you very much!

[@bigdaddyshouse]

Thank you for watching! I'm glad it all worked out brother.

[@Eric-zs6rd]

If you have to remove the radiator cover might as well remove the grill. It's only 4 easily accessed bolts. Takes maybe 60 seconds.

[@Rafael.Alvarez]

Genius.Good example of working smarter not harder.I would add for that bottom bolt before removing the headlight to use an extension magnet and pulling it out.

[@bigdaddyshouse]

I took your advice and actually made another video showing just that! Thanks again!

[@josephmalinowski6817]

I would like to know where you live because I never wanted a hug another man so much right now. Went to change my lights yesterday and gave up because I was about to take a Sawzall and cut my fenders off. Wow thank you 💯👍

[@alexromero-bm3uj]

Man!!! Thank you! It took me no time to replace the bulb without taking the grill and radiator cover off. I appreciate your video! 2016 Ram 3500.. Al R.

[@derrylwood5821]

I am disabled. This is the great thing ever. Took no time at all. Thank You Sir!!!!

[@bigdaddyshouse]

No problem Darryl, I'm glad it all worked out for you.

[@JRosco-rs2do]

No one cares you’re disabled stop wearing it like a badge. Disabled people are a drain on society

[@Rexrkerby]

Thanks man! I just removed and reinstalled drivers side headlamp assembly in less than 30 minutes. Cleaned and readjusted the vent caps to prevent condensation. If this does not resolve condensation issue I'll yank it out again and remove one of the filter screens entirely. Appreciate you posting this.

[@phazescan]

Hey this worked great! Visited the discount tool store and got a 12" socket extension and had the light out in a few minutes!

[@bigdaddyshouse]

Awesome to hear Josh! Glad i could help

[@LilJon292004]

Thanks man I just replaced my whole headlight bezels without removing the grill thanks to your video. The bezels were leaking and fogging up on me.

[@bigdaddyshouse]

Glad it went well Jonathan! Thanks for watching and the tip brother!

[@FuckYourChannels]

Awesome!!! It took me all of seven minutes to do both sides. Thank you! Little side tip... Stuff the 10mm with petroleum jelly and it will hold onto the long bolt on the bottom for going out and in with it.

[@FuckYourChannels]

2015 Ram 1500 Lonestar Eco Disel

[@bigdaddyshouse]

Glad to hear Bobby! Thanks for watching and your support!

[@barbarabecker7484]

Thanks for the video. I took my Ram 2500 to Walmart. They said they couldn't replace the bulb because they had to take too much stuff apart. I guess the guy who replaced the last bulb didn't share his secret. Now I will save money and do it myself!

[@bigdaddyshouse]

Glad I could help!

[@bossgonzalez9120]

So I have a 2020 classic. Did a similar build on extensions like you did. I only upgraded low beams to leds. Left the lower bolt/screw in place but undone. Pushed fixture outward from fenderwell door so that outer edge rotated out and I was able to swap each side out in maybe 3 or 4 minutes each. Remember to push the inner tab up to release and down to lock.

[@bigdaddyshouse]

Hey Boss Gonzalez, I'm glad you had success with it. It is quite the time saver right! I really like this method because I don't have to worry about accidentally breaking the tabs on my grill. Thanks for watching and your support brother!

[@bossgonzalez9120]

@@chuck7432 the first side was difficult at first but I remember either pushing forward or pulling back at the same time I was pulling the tab down. Leave bolts in place until you free the tab.

[@bossgonzalez9120]

@@chuck7432 any luck?

[@chuckcope1875]

I did this and it worked great. Apparently the guy that owned my truck before changed the bulb a few times. The bottom hole in the head light assembly was cut off so the bolt doesn’t have to be taken out all the way. Saved me time because the problem wasn’t with the bulb but with the harness.

[@bigdaddyshouse]

Glad it all worked out Chuck! Thanks for watching brother

[@Lordoftherims]

Did this for my new projector halo headlights. Done before sundown thanks to your video!

[@bigdaddyshouse]

Glad it helped you out David! Thanks for watching man

[@AstanaxKnight]

My almost eighty year old dad got a used 2017 Ram 1500. He was surprised to find the dealership's warranty did not cover headlight bulbs. He was also used to the bulbs just blowing, not dimming over time as he found out. I told him that I just bought some LED lights for him last night and when they come in, I will replace the bulbs for him. Your video will definitely give him peace of mind, as he freaks out when he sees me pull the plastic grille off my Jeep Wrangler, which is a lot less complicated.

[@terryford6513]

I’m so glad I watched this video. Needless to say it’s saving me time and money.

[@bigdaddyshouse]

Hey Terry, Glad I can help. And thank you for watching and your support!

[@jasonl8216]

So glad I kept scrolling to your video!!!! 5 stars rating!

[@bigdaddyshouse]

Thanks Jason L, I'm glad you kept scrolling too LOL. Thanks for watching and your support!

[@vtrdavefilms]

Thanks for the tips, my 2012 has a slider unlock behind the assembly, access thru the door in the wheel well. I also loosened up the 3 fender screws to get my hand behind the light assembly and pull it loose easier. Strangely enough, my lights just have a short somewhere, i tried to unplug the main connection but it would not come out easily but that seemed to be enough to get my lights to come back on!

[@photojunkie6991]

First I’d like to thank you for the information. I had trouble trying to get my grill out even with the two videos I watch. I only needled to replace the right front amber turn signal bulb so I found a way that literally only takes about 10 seconds. The plastic door under the wheel well leads right to the turn signal bulb. So, if that is all you need to replace, just open the plastic door, turn the bulb slightly to detach it from the headlight housing, pull it out and snap a new bulb in. Then reverse the process to finish. Literally about a 5-10 second job. Thank you Dodge for making life easier. Now I have time to go watch another UFC fight.

[@stanmeadors2792]

Totally worked! Great video! I’m glad you gave props to Cornelius 😂😂😂

[@jimmymurley4563]

Worked just like you said on 2010 RAM. Actually replaced the housings because they originals were faded so bad. My bolt heads were 10mm and used a piece of electrical tape over the socket to hold the screw in place. Easy Peezy pice of cake. Thanks!!!

[@bigdaddyshouse]

No problem Jimmy Glad I could help. And great tip on the tape.

[@richs.1591]

Worked great! Thank you. Be sure to work the socket joint side loose first, which allows some clearance near the grill to easily remove the other side of the housing. Great video. Thank you.

[@bigdaddyshouse]

Sorry for the late reply, but thank you for watching Rich! I'm glad everything worked out.

[@mikemcgee5296]

Thanks for the info , done both of my headlight less then 30 mins today .

[@bigdaddyshouse]

Right on! Glad it all came together Mike.

[@rkcsig]

tks for the video, I have to change the light bolds today.... I have a ram 1500, 2017 longhorn and it worked, very easy.

[@bigdaddyshouse]

Thanks for watching and your support rick.

[@johnpoole7327]

Thanks to both of you. To the point, mine took almost an hour for both sides.

[@bigdaddyshouse]

I love It when a plan come together!

[@marksilvestro450]

Works good. Just did my 2014 Longhorn Laramie with projection HL's.

[@bigdaddyshouse]

Glad to hear about your success Mark. Thanks for the comment and your support!

[@AZRickD]

Worked dandy for me today on my 2014 Ram 1500. I would advise putting some painters tape (or electrical tape) around hole to protect the paint as you wiggle the lamp assembly in and out.

[@bigdaddyshouse]

That's a good point AZRickD! Thanks for the additional tip brother.

[@tonyacrawford8656]

I wish I had seen this Sunday when I replaced my low beam headlight on the passenger side on my 2014 Ram 3500 dually. I did however discover that I had the wrong bulbs and had to drive to the larts store with grille and radiator cover strapped down in bed of truck and headlight assembly on bunk in the back. That's when I found out that not only do I have projection headlights (that I didn't know I had) that I also have 3 broken clips on my grille. They only have half the wing pieces. Now to find a video on how to remove/replace them... I'll try this next time. One question though. That bolt at the bottom is the adjustment bolt for adjusting the headlight beam. Will doing it that way make the adjustment shift? Or did you just loosen it up as I didn't see it come out when you took your very long extension out. I'm new to all of this. Gotta learn what I can on the fly as most of my breakdowns happen on the weekend when no shops are open. Thank you in advance!!

[@PeteATurner]

You're my hero Thanks for the video AND I get to buy a new extension!!!

[@bigdaddyshouse]

Hahahaha! Thanks Pete! Glad I could help. Thanks for watching and your support brother.

[@PeteATurner]

hardest part of the job was the return trip to the parts store to get the right bulb 💡

[@tonyacrawford8656]

@@PeteATurner That part sucks. I had to do the same thing. Now I know which ones to get. 2012 low, 2005 high for projection lights.

[@PeteATurner]

@@tonyacrawford8656 trial and error? IDK

[@dustinabston6755]

Man, I appreciate ya. I did not feel like fooling with that grill. 10 minutes... Done.

[@pushbroom9398]

😷 2 funny about a couple of years ago I had the same problem. 🤔 So there HAD 2B a better way And now you posted this video with the SAME solution I had figured out. So today I had a headlight problem didn't remember so went to u tube videos and flash backs of FRUSTRATION 😥😥 came back. Then ur video came up 👏👏👏👏 thanks for your video brought me back to a HAPPY PLACE 🤣🤣🤣🤣. So my thx for ur post . Stay safe/healthy during this period of the pandemic 😷

[@bigdaddyshouse]

I actually took the idea from you, I'm sorry I didn't give you credit brother.... Lol But for real I'm glad I brought you back to a happy time. Thanks for your support brother!

[@pushbroom9398]

😷NP it's OUT THERE that's all that MATTERS 👍👍😷

[@bigdaddyshouse]

Glad I could help. And you stay healthy too brother! 👍

[@tonywann7657]

Excellent video! Saved me a lot of time and headache. Thank you very much for sharing this video with us.

[@bigdaddyshouse]

No problem Tony. Thank you for your support man!

[@let_it_ride9216]

Going from a quad headlight to projector and I was dreading taking my grill apart thank you man

[@KP-si4rt]

Can’t ty enough brother!! I want to remove the whole headlight so I can tint them and before I saw your video I thought the whole grill had to come off....you da man thx again!!

[@bigdaddyshouse]

I was thinking about tinting my headlights too. I'm definitely doing my tail lights. That'll probably be the next two videos that come out. We'll see how much film I have left over. Glad I can help and thanks for your support brother!

[@a-fox]

If you use an extension to remove the lower bolt you are apt to loosen the lock bolt below it which controls the angle of your headlamp. So next time someone flashes their high beams at you you'll know that taking this shortcut probably raised the angle of your lights just enough to make others think you are bright lighting them.

[@oger5150]

Well that changed my days work tomorrow. Thanks man

[@bigdaddyshouse]

Hey Shawn, I hope all goes well for you. I did make a newer video that goes into depth about that lever behind the headlight. It may be helpful to have a visual before you get into it. Thanks for watching brother

[@rmcalhoun4543]

Great tip. I'm like you. I wish that I seen this 30 minutes ago. I just finished putting the grill back on my 2011, came in to get some pizza and voila your video appeared. Lol. I'll know next time I guess.

[@bigdaddyshouse]

Lol! Siri and Google are definitely listening! Well like I said to some of the other guys, like it and share it. Maybe someone else will get to see it BEFORE they've already taken their grill off. hahahaha I appreciate your support though brother.

[@johnperkins8884]

Worked like a charm! 2009 Ram 1500 SLT 4x4

[@lesb6974]

You could attach a magnet to your extension and pull that bottom bolt to remove it and keep it in place when dropping it back in the slot to reattach.

[@bigdaddyshouse]

Les you are right. I have done just that several times in the past. Probably going to do that again soon on my next video. Thanks for watching

[@kenbass346]

I suggest bumping from back inside wheel well to loosen back corner much easier less risk of scratching paint

[@bigdaddyshouse]

Hey Ken, great idea. Thanks for sharing brother!

[@rodsanchez7980]

Great video, worked liked a charm, saved so much time

[@bigdaddyshouse]

Thanks for the compliment rod. Now you have more time to watch the rest of my videos! 🤣

[@rodsanchez7980]

@@bigdaddyshouse Will do.

[@mahdiammons1577]

Good information! I changed out my headlamp in about 10 minutes. The only issue was the bottom bolt wouldn't stay in the socket... no problem! Juicyfruit gum to the rescue, mission complete 😜😆😆😆

[@bigdaddyshouse]

Hahahahaha. In the past I've used duct tape too. But then I got one of those telescoping magnets. I think the duct tape still works better though! lol I'm glad it was helpful to you Mahdi. Thanks for watching and your support.

[@mahdiammons1577]

@@bigdaddyshouse So you have a video for changing the oil on my Dodge Ram 1500 sir?

[@bigdaddyshouse]

That is actually coming soon sir!

[@gregmonz697]

All I did was open up the dust cover under the fender and twist the bulb out put a new one in and reinstall back in the hole with a twist and snapped the dust cover back on my 2010 Ram 1500 . This was for my front signal bulb .

[@williamlind2843]

LOL!! This is how I did it!! Before checking you tube!! I used a 1/4" socket driver.

[@danogara5201]

Thank you Buddy!!! Literally 15 minutes and I was done!!!

[@bigdaddyshouse]

Awesome to hear Dan! Thanks for watching brother

[@davisstratta3561]

This saved me so much time

[@williammccaslin8527]

I will check this out on mine to see if I can do it like this, but mine a 2010, thx for the vid

[@bigdaddyshouse]

Let me know if it works for you William.

[@williammccaslin8527]

@@bigdaddyshouse will do

[@OldSkoolC10]

THIS is the video I was looking for. Just got a 4th gen and have been completely baffled that the grill had to come of to replace the lights. I knew there had to be another way. Thank You For This!

[@bigdaddyshouse]

Hey brother, glad you liked it. did you just say you bought a 4th gen RAM! Well, you are in for a treat sir! Check out my alfaOBD videos and see what you can really do with this RAM. kzbin.info/aero/PLdCjicTh12KSFdkr5IITlDbiHvFWAogXP Have fun modding brother!

[@josearrvizo359]

Lol thanks buddy I just took off my whole grill yesterday but next time now got do my window regulator u know easy way

[@323232blue]

Thank you big daddy and thank Cornelius for me too

[@Edwardsjourney]

I can't wait to try this out. Thanks for the tip.

[@bigdaddyshouse]

No problem Edwards journey. Let me know your success story! Thanks for watching

[@toddbraun]

Thank you for the very informative video. And thank you Cornelius!

[@bigdaddyshouse]

Thank you for your support Todd!

[@JSKCKNIT]

Thank for taking the time to make this video!!

[@bigdaddyshouse]

Thank you for watching!

[@hemihead]

For whatever reasons, this did not work on my 2014 ram 1500 workman with reflective headlamp. 1st, I left the grill in and ended up damaging the left headlamp assembly. Then I removed the grill and removed the right headlamp assembly, without damaging anything. Also, by removing the grill, it was way easier to re-install the headlamp assemblies.

[@bigdaddyshouse]

Hey Bob sorry for the late way reply. I'm sad It didn't work out for you. I did make a follow-up video composed of a lot of feedback in these comments. It may be helpful to you. kzbin.info/www/bejne/hYXVdIV6drCApqs

[@salty2561]

Used this method on my 2018 2500; worked on the left side; couldn't get the light off on the right so had to remove the grill. But the grill was much easier than other videos showed.

[@bigdaddyshouse]

Hey Salty 25, it's not that removing the grill is necessarily hard, it's just one false move and you snap a tab and you'llhate yourself. Lol Did you ever figure out what was making the right side difficult to remove?

[@salty2561]

@@bigdaddyshouse Mine came off a little different. Took off the four bolts and it just came forward, it didn't pivot to the right some videos showed.

[@salty2561]

@@bigdaddyshouse It was just hitting the grill. When I removed the grill it just continued forward and came off.

[@haleyck1]

10 min job thanks to this video!

[@troyd.521]

Damn. It works!!! Yiu saved me a ton of time!!

[@bigdaddyshouse]

Glad to hear it Troy. Thanks for your support brother!

[@ordinarytornado]

Thanks Cornelius.

[@jaredallen1149]

Sure would have been helpful YESTERDAY... LOL Thanks for posting!!!

[@bigdaddyshouse]

Thanks for watching Jared!

[@barbararobertson1454]

Thanks for the how-to video!

[@bigdaddyshouse]

You're welcome Barbara. Thank you for your support.

[@ryanmcpherson9738]

It definitely was a very quick shortcut, but installing the last bolt with the extension I lost my socket, swivel, and extension... had to remove the grill anyways. Thx bro

[@bigdaddyshouse]

Hey Ryan, you lost all of it? I'm trying to picture that in my head. Are your sockets and extensions loose?

[@davidlaidig9485]

Thanks for the how-to. I have 2 questions. 1) What is the little rubber wedge that is laying on top of the headlight assembly? 2) What's up with the apparatus on the lower 10mm bolt? Working on a 2015 Ram Tradesman 1500.

[@bigdaddyshouse]

Hey David, so I rewatch my video trying to find out what rubber wedge you're speeding of. And then I walked out to my truck and pop the hood just to see also. I'm at a loss on what you're talking about. There are bump stops on the metal portion of the fender so when you close the hood it doesn't hit. Is that what you're talking about?

[@davidlaidig9485]

@@bigdaddyshouse no way to post a pic on here. I'm thinking that is an assist in assembly at the plant. One fell out on the floor and the other one was just laying on top. About 3 inches long 3/4 wide and 3/8 thick. Hard rubber with a wedge on one end.

[@bigdaddyshouse]

Hmmmm. That could be or maybe a bushing for vibration. Are you in the RAM forum? www.ramforum.com/forums/general-discussions.38/ If not sign up and surch big daddy's house and send me a PM with the pic. See you in the brother.

[@davidlaidig9485]

@@bigdaddyshouse yes. No worries. Just curious.

[@davidlaidig9485]

@@bigdaddyshouse How the heck do you send a PM on Ram Forum? I am DavidLaidig on there

[@heavyflippingrandmasboifir669]

What the biscuits!!!! Love this video!!!

[@bigdaddyshouse]

Thanks brother!

[@nicholasvardy9127]

WARNING!!! Problem with this is, the bottom bolt way down there also has the headlight adjustment nut attached to it, and it you didn’t make sure it was secure you could majorly screw up your headlight angle. Just a warning!!

[@JLUnlimited]

This is s good trick and tip. For my 2015 2500.. The grill did have to come off. It is only four 10mm screws from the top. But thank you for the video..

[@workatnowhere108]

Thanks Cornelius im doing this tomorrow!

[@bigdaddyshouse]

How did it go?

[@workatnowhere108]

@@bigdaddyshouse not good! one of the headlights was broken 😕 I had to send them back!!

[@bigdaddyshouse]

Damn man. Broke in shipping? I know the feeling all too well of waiting anxiously for something and it's showing up broken..... Sorry to hear that brother.

[@mackerpacker4600]

Dude!!!! Super helpful!! Great tip. Worked awesome

[@bigdaddyshouse]

Thanks brother. Glad It helped.

[@scrapplepig]

To get the bottom bolt back in, tape the bolt to the socket them put it back in.

[@bigdaddyshouse]

Great tip brother! Last time around I actually attached a magnet to the socket and that also worked. I think I like the tape idea better though. Thanks!

[@scrapplepig]

@@bigdaddyshouse I got that idea from a friend. When we were younger my friends parents had a big glass jar with a narrow top half filled with quarters. He was afraid to tip it over because he thought it would break, I told him to get a fly swatter and on the handle end put some tape to get the quarters out. It worked and I figured get them out you could put them back in.

[@carlosllama9979]

Man, I was awesome. I wish I would’ve seen this video three months ago. Thank you.

[@primalcontact03]

Great video.Maybe next time show every piece you touch like the L bracket.Very helpful though.Thank you.

[@bigdaddyshouse]

Hey JD, I appreciate the comment. I've definitely gotten much better at making videos since this one. For some reason this one is picking up a lot of steam. I appreciate you and thank you for your support brother.

[@primalcontact03]

@@bigdaddyshouse No problem man. Keep up the good work.

[@Myoldiesrecordings]

Works well but getting the screw back In with those extentions might make it more worth while to take the grill

[@this_snits_world_]

Hell ya. This is how I did it 2016 Used a 10 mill, so it was really snug to get that extention part of the job 👍🤙

[@user-is5jd4ci5r]

Damn man!! This worked! First time I changed my bulbs, took the grill off, based on other videos! Big thanks to you and Cornelius!!!

[@JuanGonzalez-li3pk]

Awesome... Gracias Cornelius...Thank you for sharing this with us.. Semper Fi...

[@chazzcrowchild6726]

Genious I will be doing this tomorrow to replace my light bulb because I do not want to messing with the grille for one bolt😂

[@chilamilla]

Genius*

[@chazzcrowchild6726]

@@chilamilla as you can tell definitely needed the help

[@bigdaddyshouse]

Hey Chazz, Did it all go to plan?

[@thomashozey4899]

On my 2015 2500 6.7 there is a panel you can flip open in the wheel well (passenger side only). On the drivers side, I just reach up under the front side to access the bulb.

[@RickLove86]

What headlight assemblies are those? And do you like them?

[@xmradio11]

After removing the bolts and clip, push the light out from the back through the hole.

[@Knuckledragnation]

So did you have to pull back the top radiator cover from each side? I’m new to owning a 4th gen Ram Diesel. ✌🏽

[@user-zs3gd8fs9r]

Love those headlights. Where can I get a set?

[@TheNovaNorm]

Oh, I can't wait to do this next time! Taking the grill off in cold weather will destroy the little clips. Ask me how I know this.

[@bigdaddyshouse]

Honestly that was one of my main concerns is breaking one of those clips off. gives me anxiety every time I pulled the grill. Since I figured this trick out I've never pulled a grill again! I'm glad you find the information helpful and Norm

[@TheNovaNorm]

@@bigdaddyshouse , welp, had the lights out several times so far in 2021. A couple times to change the lights and at least once because I forgot something. This method works great!

[@lindapoworski2597]

All as you explained but I just can't get the assembly off that retaining pin that holds it in. I have nothing to grab onto and don't want to pry it off with a tool in case it breaks.

[@samsantarita1680]

Freaking amazing. I worked late but wanted to install my Morimotos that had arrived in the afternoon. I was planning on a 2 hour job but thanks to you I installed both headlights in 45 relaxed minutes. 45 minutes including time for me to watch the install video from Headlight Revolution. Thank you

[@servantsoldier5207]

Thank you! Cornelius URDMAN😎

[@livingthedreamhomestead1589]

Thank you so much for sharing and posting this. This would of came in handy a month ago 😆

[@jon_pitt]

I’m gonna take a swing at this right now.. good lookin out!

[@bigdaddyshouse]

No problem Jon. Did I come together okay for you?

[@jon_pitt]

@@bigdaddyshouse worked out great

[@billyhenard1473]

I have done all that you show on the video but cannot get the part of the headlight assembly closest to the wheel well assembly to release. I can’t get my fingers under it to pull out. 2013 Ram 1500 that has never had the head lights removed. Can I apply pressure from inside the access door inside the wheel well to help the ball seat on the back of the headlight assembly pull out of the hole that accepts it ? If so where is a safe place to push against the back of the headlight assembly? Thanks

[@AlexTapia8616]

Wow my dad had to fiddle with both of them for a couple hours this is definitely going to help when I plan to upgrade my headlights

[@gilhernandez605]

Miss your vids, hope you come back soon

[@323232blue]

Explain the sorcery, I paused your video right there cuz I had to laugh

[@willoperez62]

On my honeymoon but as soon as I get home doing this thank you

[@RK_Insanityy]

Only problem with doing it this way is that bottom bolt is also an adjustment for the positioning of the headlight so taking it off this way you run the risk of turning that pice on the bottom which raises and lowers the headlight

[@FatThor215]

Just did it to my 19 ram classic 1500.. works perfectly.. easy to do.. saves a lot of time thanks

[@bigdaddyshouse]

Glad to hear BMeL, Thanks for watching!

[@georgioantoine4194]

60000kms on a 2022 ram and bulb is burnt out WTF. POS. AWESOME VIDEO.