Bike me Lithium Battery: Self Start Problem finally SOLVED!!

[@chandra.s]

Bhai ek saal ho gya tume ye jugaar kiye abhi bato ke koi dikkat aaya h kya or

[@FreeCircuitLab]

Kabhi kabhi trip ho jaata tha, 220uF laga diya, abhi fine chal raha hai 6mahina se... No problem

[@chandra.s]

@@FreeCircuitLab 40A me konsa lagau me

[@pitambersahu2516]

Bhaiya CM​1041GTic me capacitor Kahan par lagaye 4s20Amp BMS LifePO⁴ battery balancing 12.8 v dc please reply 🙏🙏🙏🙏@@FreeCircuitLab

[@anoonymous313]

​ Bhai Mera ek sawal hai mere pass 70 CC motorcycle hai Maine usmein 3 empier ki lithium battery lagai hai bike self start nahin hai agar battery ko utaar dun powerful dress per motorcycle ki voltage check ki jaaye to bahut ribbon 26 volt tab bhi chala jata hai lekin battery ke maximum voltage. 12.6 hote Hain to isase battery kharab ho jaati hai mere bike mein takriban do battery kharab ho chuki hai hota hi hai ki sirf ek series wale se nahin kharab hote hain aur voltage 8.4 per a jaate Hain. Aur dusra batlayiye pesh aata hai ki jab battery ful charge Ho jaati hai to battery input or output donon ka nahin deti yani jab bike chal rahi ho aur battery bhi ful ho to battery se current nikalta hi nahin hai jisse Na to motorcycle ka Horan Sahi jalta hai aur na hi motorcycle ki lights agar bike ko band kar dun yani star na rakho to battery se current aata hai is masale ka hal Bata den ek HAL to yah hai Jo Maine socha hai ki battery se diode lagakar BMS ke bagair output Li jaaye lekin masala yah hai ki vah cut off nahin Karega battery ko aur battery jyada discharge ho sakti hai jisse dobara charge nahin hogi kyunki BMS 8.4 per cut off kar deta hain please help@@FreeCircuitLab

[@bhagatsinghfan4037]

2:00 Bhai jab battery open kar k hi use karni thi toh simple Lifepo4 cells le leta ₹600-700 k 4 cells mill jate . Itni mehngi battery kyo Li jab wo kaatni hi thi

[@Clarkdale44]

Nice, I just modified 3s40A BMS in similar way. After placing capacitor, the protection is delayed, I haven't tested for how long since the vehicle starts very fast using self. I used 100uF 25V cap. Can't believe a tiny capacitor solved this problem. Huge thanks to you! But main kisi ko recommend nhi karunga ki vo Li-ion battery (18650) ke saath ye experiment kare, vo dangerous hai and vehicle ke andar toh bilkul nhi honi chahiye. BMS ke electronics kabhi bhi dhoka de sakte hain and battery blast bhi ho sakti hai. Maine ye bas ek experiment ke taur ke kiya tha ki kaam karta hai ya nhi and main es battery pack ko different application me use kar raha hun. Agar aap logon ko apni jaan aur gaadi pyari hai toh 18650 based battery pack ko apni Bike/Scooty mein nhi laga oge. Video mein LiFePO4 battery ka use kiya gaya hai jo ki safe mani jati hai. Sirf esi battery ko aap use kar sakte hain Bike/Scooty mein video wala jugad laga ke.

[@sanjubanik7750]

Please help me.... I've a problem Actually in my board the registrar value is 101...so what can i do.... please help me sir

[@Clarkdale44]

Share circuit board picture.

[@sanjubanik7750]

@@Clarkdale44 sir your wp number please....sir kaha par share karna hay...insta id please

[@memepura_]

where do you put those capacitors??

[@Clarkdale44]

@@sanjubanik7750 Accha ek kaam karo, 2 wire lo aur usko 100uf 25v capacitor mein solder karo, minus wala wire battery pack ke 0v/b- wale point mein connect karo, and plus wala mosfet (big black 3 pin component) ke legs mein ek ek karke connect karo and gaadi ko self dene ki koshish karo. Jis bhi leg mein connect karne se self ho jata hai, us leg mein plus wale wire ko solder kar do. Par ye apne risk pe karna. Wire galat jagah lagne se mosfet kharab bhi ho sakti hai.

[@tanishqbhaiji103]

Aapki undertaking bahut acchi hai BMS circuit ki. Good work 👍

[@soumitramandal7930]

Dil mein bahut dard rakhke 😄😄👍👍👍, তুমি genius ভাই, তুমি বাংলার গর্ব।

[@prashantmallya-es6ek]

Bahut badhiya Bhai, ye cheez me last year se puch raha tha

[@nikhilsaxena2010]

Maan gaye bhai kya dimak paya hai pure utube ka solution day diya😊

[@ashisroy101]

10:18 ami gan e sun6i. Valo valo gan ho66e, shreya ghoshal ❤

[@srvideoediting6646]

Bro _18650_ Battery sa 12V 3A Ka router UPS banao. 3 Routers chala na ha. Backup 5 hour's hona chaiya.

[@tanishqbhaiji103]

Use LFP if you want 5 Hr backup, load current batao router PE se padh ke.

[@srvideoediting6646]

@@tanishqbhaiji103 Total 3Router's ka Load (3Amps) ha too [20Ah] ki battery honi chaiya fir up to 5hr ka backup mill Jay ga {2,000-mah ka 10 Cell} ya or 1200mah ka 16Cell lagana hoga. Router Ka liya over voltage 100% protection honi chaiya. Router very Costly ha

[@tanishqbhaiji103]

@@srvideoediting6646 I would recommend 4S 18A using 12*32700 6Ah LFP cells with 4s 30A BMS common port and use a 13.6V max charger. You can get 15V SMPS and use 5A CC CV buck converter for charging the battery and connect router directly to the battery. Router can take 16V absolute maximum. I have worked with routers and the main limitation for input voltage is the input capacitor which is rated for 16 volt and be sure to use individual fuse for each router for extra safety. 13.6V is 3.4V per cell which 98-99% charge for LFP battery and is safe for the router too. Router will consume less power in reality around 50% nominal power so expect around 10 hour backup in real case scenario.

[@tanishqbhaiji103]

@@srvideoediting6646 I am using same technique but smaller battery pack for my router and ont switch which delivers 1-1.5 HR backup depending on load from 1200mah battery 3S li-ion.

[@tanishqbhaiji103]

Will cost around 5500 if you know where to get the cells.

[@dr.hemantbiswas6304]

बहुत अच्छे से बताया। Thanks 🙏

[@BhagvatKale-pz2yz]

ACCHA KNOWLADGE HAI BHAI APKO BMS KE BARE ME GOOD WORK

[@anantalalsarkar3323]

প্রিয় মণ্ডলবাবু, আপনার কোন তুলনা হয় না! আপনি নিজেই নিজের কাছে অতুলনীয়। এটা সম্পূর্ণ আমার নিজস্ব মতামত।‌আজ দীর্ঘ দিন যাবৎ আপনার ভিডিও দেখে আসছি, কিন্তু কোন দিন কমেন্ট করা হয় নি ! আজ ই প্রথম। অনেক কিছু আপনার কাছে শিখেছি। 0:22 😅😮আমি এতটুকু বাড়িয়ে বলছি না।যা বলছি অন্তরের অন্তঃস্থল থেকে বলছি। পাওনা দেনার কোন সম্পর্ক নেই। আমি বর্তমানে ৭২ বছরের, আর ক'দিন ই বা বাঁচবো।‌ভাল থাকবেন। আরও নতুন নতুন ভিডিও দেখার অপেক্ষায় রইলাম। শুভেচ্ছা জানাই।

[@FreeCircuitLab]

Thanks

[@pratyuskoley3241]

Khub valo laglo video ta. Amar bike eo same problem hocche. Ami o tray kore dekhi.

[@ethicalaspirant6630]

Genius দাদা ❤

[@Amitkumar12300]

Sir very good knowledge, aapko kafi deep knowledge hai circuit ke bare me

[@CommonID]

Deep learning ❤❤❤❤ 👍🏻👍🏻👍🏻👍🏻👍🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻 Thank you so much

[@sanjibshah6857]

Good

[@Tarkeshwar_Roy]

सचमुच बहुत अच्छी जानकारी है और काफी रिसर्च भी किया गया है। अगर BMS के पॉजिटिव के बजाय डायरेक्ट बैटरी के पॉजिटिव से गाड़ी को स्टार्ट करेंगे तो भी काम हो जायेगा, थोड़ा सा वायरिंग का काम करना पड़ेगा।

[@FreeCircuitLab]

BMS positive me cut nhi krta hai. Negative me cut krta hai. Bypass karenge to battery ki protection nhi rahegi

[@Tarkeshwar_Roy]

​@@FreeCircuitLabMaine Jo bataya wo BMS ko bypass karta hai, Han bilkul sahi protection compromise hoga.

[@anshugenius8004]

Sir aap बेहतरीन समझते हैं 🙏🏻🙏🏻

[@rajanne2947]

Thanks a lot! My ups was tripping!

[@burneybuddy575]

Good work pr bhai mere itni mehnat krne k bajaye ek wire bypas krke direct self ko dedete or unke bch m 20 amp ka 3 diode parallel krke lagadete to hjyega or self lene k bd diode ki waja se batteru charging bypass nai hti bms se hi rehti simple h

[@MansoorMemon-hk9tt]

Very important video. Good effort. Thanks.

[@teachtecinfo1610]

Bhai apki educatin mn ap ne konsi digree li h . Ap ne apni about mn physics likha h but asal mn ap ne ya sub khn se sekha h . Yar bht kamal ki knowledge h ap ki bhai

[@teachtecinfo1610]

Or bhai agr hamen ya sub sekhna h ap ki trhn to kossa sub ject len ko kiya ya onlnine ho sakta h . Mn out of country se hn kindly guide

[@anshuyadavsitaram7053]

Very best video on KZbin 👍❤️

[@EngineerPavan]

भाई आप की आवाज गजब है और video 1 no खुपच छान❤

[@DubaakjiMotionPicture]

Bahut khoobsurat bhai Maza baand diya

[@TechnoSaquib]

You are genius Boss

[@cisarvialpando7412]

Yes🔥🔥🔥

[@Sud_cool]

शानदार भाई।

[@anandakarmakar5786]

R o 2 to MOSFET parallel lagie pcv te soldering kore dile valo hoto, blank space to pcb te chilo. Overall informative nice video

[@FreeCircuitLab]

SMD FET nai

[@digital210921]

Very informative video of bms.keep it up bro

[@Devil_inside-]

Very informative video bro..👍🏻👍🏻👍🏻👍🏻

[@akdgamer1065]

Thanks bro mainey 18650 sey banaya tha BMS se nhi self ki direct chalata kharab ho gyi👍👍👍👍

[@simisumi1030]

Bohot bohot shukria❤❤❤

[@rajanne2947]

I subscribed!♥️

[@santoshwhy2943]

Bahot badhiya experiment Bhai ji. Iska log term experience jarrur share karna taki ye safe hai ya nahi pata chale . ✌️

[@yys9801]

Explanation bohut acha kiya, aur koi fake nehee lagta, thanks Mera doubt , 10 amps ka BMS ka jo board dekhya apne, purana bike (RX100) Bina modification ka horns, blinker jalega a? Kai ke bike Mai self start nehi hai, Thanks

[@marketanalysis1203]

Wow nice learning video 👍

[@zuhaibbirds9927]

bohat khoob 👌

[@sonupradhan8841]

gajab bhai aap to ginius ho sir good

[@elec_trick]

Diode lagane se kaam nahi chalega kya battery negative aur bms ke negative ke bich ?

[@sadiruddinansary9418]

Kya 12v 60 amp ke bms me bhi condensor istemal karna parega??

[@merajkememes7403]

Sir mujhe bike ke liye lifpo4 ki battery banana hai kitne Ampere ka bma lagana honga... Pura zero se start krna hai matlab kisi battery mein modification nhi krna hai new banana hai sab

[@SujanGirii]

Aise to spot welding bhi kar sakte hai, thanks for the idea 💡

[@bhagatsinghfan4037]

2:00 jab battery kaatni hi thi or ye battery kyo li simple Lifepo4 k cells le leta ₹600 me pad jate or ye battery toh 4× mehngi hai .

[@debmalya6144]

Sir battery ke upr pressure ayega na 30A bhejne ke liye ? Kya hum ak capacitor(4700uF 25V) parallel pe de sakte battery ke terminals pe -bms ke pehele ?

[@hetexperiment28]

Bhai aur lithium use karna hi hai to koi option hai ? Jaise ki hum ek cutoff circuit laga de overcharging na ho is leye and bike ko Direct connect kare battery se

[@manojpradhan2717]

Bhai if we remove the sound resistor it will not cut the power naa ?? It should be fine naaa or any problem will occur ..❤❤

[@rahulvishwakarma6860]

Bhai tum to genius ho

[@thekhan9756]

capacitor ko output point par laga saktey hain kya?

[@ssinvest1313]

Bahut great idea but I will use 40Amp BMS and attach a 220mfd capacitor with LifePO 6000mAH batteries.

[@seemanprabhakaran224]

Can we not use a soft start circuit , with relay and resistance for few sec delay and then bypass , to battery ka surgery nahi karna padta

[@itz_revotorq_dbswr]

Kya lifepo4 bike battery lagana safe hai charge hote time gadbad toh nhi karegi?

[@dhrubajyotimitra6210]

Excellent brother. Very good job. But can you tell me why BMS companies didn't make that modification that you did. And can you please explain what are the disadvantages of this modification. Thank you brother 🤜🏻🤛🏻

[@mr.m2952]

Sir You are genius 🎉

[@mdrohan326]

Moje Pagal bana doge keya yearr,,,Etna mast video kon banata hea, dil se dowa hea meri vai

[@SANJAYYADAV-bp4uu]

Bhai 12 volt 6 empier ki jagah 12 volt 12 ampere Lithium phosphate Laga sakte hain bike mein

[@brahmanandadas729]

No perfect for real life But good job bro.

[@thekhan9756]

30amp bms mein kaunsa capacitor lagayein?

[@biswanath555majhi]

B(-) ko bypass kor ke agar ek diode laga ne se self start ho sakta hai kya

[@kailashsuthar2509]

Thermocouple se related project ka video banaye😊

[@unknowndimension5829]

Dada mein 20 Ampere wala BMS use kiya hu but uska circuit thoda different dikhta hai to isliye mujhe samajh me nahi araha ki delay ke liye capacitor kaha lagana hai.

[@muhammadraavi9357]

G ye log reply nahi karengay Im also facing the same issue

[@anchorpanasonic9253]

You are genius man

[@cisarvialpando7412]

Kya bina bms se laga sakte hei lithium iron phosphate battery ?? Kyuki S.K. Electronics KZbin channel ne dikhaya kinlga sakte hei

[@FreeCircuitLab]

@@cisarvialpando7412 bina BMS se bhi cell chalega, bas kabhi Short, over charge, over discharge nhi honi chahiye

[@Ankit_M]

*Mene Yeh Video Link Diya Hai Kya Is Traike Se Battery Hum Bana Skte Hai..?*

[@Ankit_M]

kzbin.info/www/bejne/mnuuepmtfJt5jdk

[@govindchoudhari-uy3mh]

Osm bro.. Genius..

[@thegreatshow001]

Bohot badhiya bhai , lekin bhai amaron ki battery 1500 mei mill jaati hai phir itni mehnat kyu karni

[@anchorpanasonic9253]

Kya yah battery inverter testing mein chal sakti hai

[@sanjubanik7750]

Sir mera bms mey wo smd register 101 matlab 100ohm ka hay..wahi se ic par ja raha hay ..to may usme kitna value ka capacitor lagau? Please batana sir

[@sanjubanik7750]

Sir please reply kijiye?

[@A_NNS_Galaxy]

32650 Lifepo 4 battery pe 4S 30A BMS lagane pe bhi koi jugad karna padega kya?

[@FreeCircuitLab]

Yes. Short protection ko delay karna padega

[@GauravSharma-yx2bu]

Use higher ampere bms, fir ye problem nahi aayegi or na he ye extra jugaad karna padega. Main 4s100A bms use kar rha hun. Ek dum mast chal rahi hai battery. Or sabko Rectifier sey aa rahi voltage check karna bhi batao ki wo constant rahey, warna ye battery charge nahi hogi.

[@FreeCircuitLab]

High amp BMS lagaoge to overcurrent protection nhi rahrga. 100A ka protection trigger hone se phle battery fuk jayegi

[@BBE96]

Without self bike ke lie kitne minimum battreis Jodna padega jaise cd deluxe

[@bhagatsinghfan4037]

Only 4 cells 6 AH ki . Me bhi same lagai Hui hai

[@pankajubhale4161]

Bhai, meri bike kick start hai to muze modification koi jarurat nhi hogi, lekin muze bms kinte amp ka lagana chahiye please batao? Battery pack banana hai 12v 2,5 ah ka 18650 nmc battery ke sath.

[@FreeCircuitLab]

10

[@artofanything1005]

Lifepo4 bms ka kaha lagega capacitor 220u ka usmay 4 cell lagtay hain

[@RajeshKumar-dq8qr]

Nice information!!!

[@crazyguy7585]

kya ye bullet 350 cc per chalega

[@mishraji6313]

Mobile Phone ki battery laga sakte hai kya

[@chandangupta-t1w]

Agar SMT R009 Ko circuit se hta de to chalega?

[@FreeCircuitLab]

@@chandangupta-t1w yes

[@saiaudio3228]

Good work Bhai

[@parikshitkumar593]

Bhai Mai 20 amp bms se lifo battery me 6amp k diode lga diye hai jisse ki..trip na ho....aur over charge bhi na kre..ye sahi hai na??

[@bhagatsinghfan4037]

But diode 1 side hi current flow hone dega . Tumne discharging k liye diode lagaya hai kya , agar esa Kiya hai toh bohot Sahi hai. Discharge diode se hoo jayegi or charge BMS se 👍🏻 But 1-2 diode or laga do parallel me jis se jyada high current ki wajah se diode blast na kare

[@Anush-pv7ro]

ये battery मेरे 4s bike me led bulb or led headlight k liye चलेगा क्या pls tell me .

[@subhasbiswas6694]

Bhaia bms ke madad se battry series main charging hota hai ya paralal main hota Hain... Agar paralal mai he to kaise bataye...❤

[@FreeCircuitLab]

Series me

[@subhasbiswas6694]

Maan lijiye series main lagake 3 battery 13v se charger hoga? Bina bms ke...

[@FreeCircuitLab]

@@subhasbiswas6694 hoga, saare cell same hona chahiye. Ek bhi cell 4.2 pohoch jaye to bandh karna padega

[@subhasbiswas6694]

Thanks 🙏 bhaia

[@viralmakwana1485]

Mene 60a bms use kiya aur acche se chal raha hai koi problem nahi hai

[@Amitkumar12300]

Sir can I use LiFePo4 cell in my laptop battery for long backup?

[@jowharali3799]

#Genius bro 👏

[@Manishkumar-7870]

kya ye proses 3s 40amp me hoga

[@mahiranjan]

Without bms ye battery work karta hai koi problem hoga kya aage

[@Clarkdale44]

Yes, work karega, but zyada se zyada battery kharab ho jayegi 2-3 charge ke baad.

[@adilhusain800]

BMS ko modify kiye Bina ham diode se bhi kar sakte he Jo current ke back flow ko rokega.

[@Clarkdale44]

Ye diode se mumkin nhi because current flow bahut zyada hai. 200Amps ki baat ho rahi hai. Normal diode kaam nhi karega ya phir lagate hi aag pakad lega.

[@soumikmondal658]

100amp akta blackcolour er bsm ache jeta li-on and li-po dutoi support kore tar opor akta detail video banao akdom confusing bms. Ami akta baik er battery banabo

[@vikram3775]

Good bhai... But kabi bike galti se Gear me ho aur self dab jaye to, engine ko start karne ke liye jayda current battery se khichegi aise me highly chances hoga ki MOSFET jal jaye.. To. According to me ...aisa kuch arrangement karna hoga ki self Press karne ke saath hi external MOSFET se bhi kuch current ka distribution ho ... Aur inbuilt bms ka MOSFET jlne se bach jaye..

[@Clarkdale44]

Sahi kaha, jab self key press karte hain toh (sirf us time ke liye) bike battery se directly connect ho jaye (bypass bms), release karne par disconnect ho jaye. But ek hi problem hai, thick wires lagane honge. Ya phir delay off switch, jo on hone ke 5-10 second baad auto off ho jaye.

[@elec_trick]

Bms ke main negative supply aur battery ke main negative ke bich agar diode laga de to ??? Usse bike self start bhi hogi aur overcharge protection bhi milega kyuki reverse current nahi jaega

[@akram10211]

60 amp BMS se .. rtr 160 4v normal start hoga kya?? Bhai please reply.

[@Clarkdale44]

Nhi, jitna bhi laga lo bike start nhi hoga. Bike starting motor lagbhag 200 Amps leti hai toh 60 Amps ke BMS se kaise chalega, aap hi batao?

[@elec_trick]

​@@Clarkdale44 bhai diode ka try kiye kya ?

[@Clarkdale44]

@@elec_trick Not possible with diode.

[@sahibsaifi2254]

Bohot bAdhiya

[@aadishaktiautomationelectr165]

You are the best

[@itz_revotorq_dbswr]

Bro kya tum ek 5v mobile charger bike battery se bana sakte ho sirf powerbank module aur resistor use karke

[@deepakkharethankyou8094]

Thanks sirji

[@jhatechnicals5151]

Helpful idea

[@imroogaming5025]

Aghar hum 15 ampere ki battery mein 10 ampere ki BMS lagaein to us sey kia hoga?

[@Clarkdale44]

Koi dikkat nhi hai eysa karne mein.

[@swapnilraut2561]

Bhai mere paas Royal Enfield Classic 350 bike hai aur uski battery 12V 14Ah hai. Lifepo4 ki mai battery banana chahata hu. toh usake liye mujhe konsa BMS lena chayiye taki bike selft start le sake. Please bataye. Thanks.

[@Clarkdale44]

Bike self start le bhi sakti hai aur nhi bhi, depend karta hai BMS ki quality aur bike ki self motor pe bhi. Usually uske liye kam se kam 200 A ka BMS lena padta hai. Lifepo4 battery ka pack 4s 2p ka banega jo ki 12v 12Ah ka hoga (agar 6 amp ka ek cell hai toh). 8 cells lena hoga. 4 cells series mein and 4 parallel. 40A ke BMS ke saath bike self start karne ki koshish karna, ho gayi toh theek hai nhi toh jaisa video mein modify kiya hai vaisa kar sakte hain.

[@sathieshchandar6187]

Peak current for bullet is 145 amps. Hence BMS should be able to handle atleast 160~170amps peak current.Also battery cell used should be minimum 12 C or more.

[@Musitech007]

Sir lithium ion 3s 25a board me kaha pe lagega capacitor mene jo diagram apne bataya tha uske hisab se to kuch difference nahi aya aap please physical board me kaha lagega uska 1 photo update kardijiye please

[@francypolly]

Isme kithna ampere ka bms lagaaya he

[@vinodkumartech]

Sir aap konsa bike use karthy hai

[@santoshwhy2943]

Bajaj CT 100

[@msarankumar5132]

super,keep updating....

[@inderdeepsingh137]

I am using BMS-20A-3S-S made by Shenzhen Global Technology Ltd. Can you please guide me where should I add capacitor and how much value