Blade MCPX Setup Video 1

[@fourstringin]

Thank you for this video. I just got a DX7 and was completely lost on what all this settings meant. This was a great explanation. I have watched a lot of videos but this was the best. Top it off you don't have an annoying voice or unnecessary pauses or overly explaining. I love right to the point.

[@Nytro97]

Rob, Great information.....I have the DX7 and used your settings and they work fantastic. Thanks for posting this video.

[@iZilly]

Great,,, by trying to clip off the pushrods to adjust them, i accidently broke the rear one.... LOVELY!! and where do i get a new one of those???

[@RcStorm450]

Very well explained Rob, clear and precise instructions thank you.

[@fridgewater3]

hi m8 just got my blade today ,just wanted to say cheers for setting worked great , the little bugger kept drifting left sorted out though never flown flybarless before felt bigger ... raptors 60 normal chop anyway cheers really good vid ....stu

[@KitelessRex]

Hey GREAT video. I will do this to my MCPx and post a video response. Thanks again, I was not liking how much positive stick you had to give it just to hover and it would drop like a rock because of all the negative. This also makes doing flips & loops a total pain.

[@Blacklamass]

Thanks very helpfull, is it normal for the tail motor to spin up before the mains ? Cheers

[@Blacklamass]

Thanks for the reply, I see you run the weighted blades, I have to run these as the tracking is way out on the others and the heli wobbles all the time with them on, shame as I can feel the heli likes the light blades better.

[@Gairlochan]

Thanks mate, really helpful. One thing though … I have a DX6i and the TRAVEL settings are different. There is no SERVO page, just a TRAVEL ADJ page, on which I can set only a single value for each setting, i.e. for PITCH I can choose a setting from 0% to 125%, but I cannot set a range from low 70% to high 74%. I have set it to 75% as is recommended in the docs, but I was wondering … what's the difference between the way my machine sets one number and yours allows a range between two?

[@Gairlochan]

@Trainboy64 , Thanks for the tip. Pity they don't put things like that in the manual … I'll try it out when I get a chance :-)

[@HansOlofViktor]

Hi Are you using a Mode 1 transmitter? throttle on right side. What I can see in video it say mode 2 on your transmitter. I'm confused. Well, my MCXP will not fly for me so I wounder. /Hans

[@UtRadioGuy]

Hey Rob! I FINALLY ordered me an mCPX V2 from HH. Any tips you can give me would be great. I've never flown a CP heli other than on the sim, but I should be able to pick it up really quick. I fly my mCX2 so hard it can't take some of the moves I try with it, thus getting the mCPX V2. Thanks!

[@gsizzlepmg]

Hi are those lighted blades on your heli?

[@UtRadioGuy]

@Trainboy64 - I sent you an email about a week ago about buying it. Did you ever get that email? Yeah, check out the new mCPX V2. I guess they made the tail rotor bigger, and the new AS3X Digital Flybarless System. So I waited just long enough to buy one! I look forward to hearing from you on how to set it up. I'm sure I'll have a ton of questions since I'm new to CP. I did download the settings onto my DX8, now I just need the heli to get here. Talk to ya soon!

[@chicos445]

Hi one thing i dont understand how could you know what your actual pitch is at,without using a pitch gauge,for example 3d curve of -10 =10 and 0 degrees half stick,thanx

[@mtbjr91]

If I change the pitch on the heli and am useing the stock controller is that a bad thing to so

[@MaRlBoRoMaNkHuNRoBbYKaP]

missing the dual rates and throttle hold cause some have no clue just saying not everyone knows these setting but its dead on and your setup is awesome super job

[@TheScout53]

hay rob,i used your settings for the mcpx.i bined it to my dx8,when i increase thr throttleit takes off but falls back down to ground and the binding light on the heli starts to flash.i need help please

[@TheScout53]

can you bind the mcpx to spectrum dx5e tx