I tried a battery and 24 v power supply. Thank you for your response.
@_kvngmilton_55225 жыл бұрын
And what happened
@bushellj6 жыл бұрын
When the board initialises or blutooth devices pair with the board it beeps at you at full volume !!! Doesn’t appear to be any way to stop this. Board creates lots of pops and crackles through the speakers that appear to come from the Bluetooth module. Needs to be implemented with a bit more care !!
@helmar2424 жыл бұрын
Eu também quero resolver isso. Ninguém sabe como? É muito incomodativo :(
@gilsonnovais3045 жыл бұрын
Datasheet says 2x 50W from 21V. I didnt saw any about 60W or 120W. There are 2 TPA3116 in this board?
@nexianspace7746 жыл бұрын
Hello. Can you tell me how we change mode from bluetooh to AUX? There are aux with 3 hole LGR. I put a stereo female jack there. But didnt work.
@jenovaizquierdo5 жыл бұрын
This model of amplifier is only Bluetooth and there is no switching to AUX.
@M0beast5 жыл бұрын
anyone know how to remove background hiss on this amp?
@jimcatx30904 жыл бұрын
M0beast ya you throw it in the trash
@justsum67054 жыл бұрын
@@jimcatx3090 and ur mom
@Pimot014 жыл бұрын
kzbin.info/www/bejne/d4ial6WXisdll5o
@rdvancoban52305 жыл бұрын
is it really 120W? it looks like it cannot even move your woofers forth and back :D
@mmarfe5 жыл бұрын
The problem with some of theses amps is that they have a low pass filter, if you figura out which capacitor to replace it plays full range. I don't know why they do that.
@stephenellam33256 жыл бұрын
My Bluetooth light is constant blue from initial start up , any idea how to fix this as I can’t pair
@lolipopsandfancypants72572 жыл бұрын
I got one of these for $3 cdn but the power jack is ripped off. Don't suppose you know the pinout of the barrel jack receiver to the board or where I should jump 12v to on the board to work past this. Or where to find a schematic or datasheet.
@domenicocarandente60286 жыл бұрын
The power of this board is false - (FAKE) -, under the heat sink there is only one ic tpa3116d2 and NOT two ic's in PBTL, so the maximum power is 30Watt @ 8ohm 24volt or 50Watt @ 4ohm 24volt. That's all.
@jenovaizquierdo5 жыл бұрын
That what I thought it was fake. I'm using this amplifier with 60 watt each channel and is working the problem I think is the right amp. I had a problem when I use all the volume it shut down and I was looking and forums and it say you need to use a 12v and 5amp and it work perfectly.
@alexiulian28315 жыл бұрын
What maximum power can i get with 4 ohm speakers at 12v?
@1Patient6 жыл бұрын
Ya, looks like a good.bluetooth device. Do you know what version of bluetooth this board supports? How is the bass, because I couldn't see your woofers moving too much.
@cesixful6 жыл бұрын
it has CSR8635 bluetooth 4.0 chip. Should support all bluetooth devices :)
@guherrera846 жыл бұрын
Hello! Are your speakers powered by or powered by the amplifier board? What is the volts and amper of your source?
@AnthonyCamposL5 жыл бұрын
At 24V, how many amps do you need to work correctly?
@als-techreview5 жыл бұрын
I think 2A will be more than enough on 24V for this amp.. but if it's higher is ok.. even better.
@PaulGariepy5 жыл бұрын
watts is volts X amps so for this to put out RMS 120w per ch you need at least 10A (50% duty cycle) (120/24=5a per ch)
@oscarsodano9931 Жыл бұрын
Hola te hago una pregunta cómo le pongo una entrada para un instrumento a este módulo ?
@istiksnamimisska5 жыл бұрын
Is it possible to add line in instead of bluetooth?
@attilasipeki14183 жыл бұрын
Is there any way to change the bluethoot connection name?
@daleksec85436 жыл бұрын
Can i use for left chanel a speaker 8ohm 250w and 125rms. and for right chanel a tweeter 150w 8ohm ? I dont know so good about amps and speakers (and my eng its not so good ) 😝
@jenovaizquierdo5 жыл бұрын
It won't work or you will damages the speakers or the amplifier. You need to use less then 110w for each channel
@f.a32025 жыл бұрын
i doesn't matter. it will work. the speaker ratings are the maximum power that they can take it hasn't to do with the amplifier. only be careful with the speaker's, with this i mean that you should use speaker's with rating up to 50W more than the amp can provide
@malikobaidul60134 жыл бұрын
How to connect aux in this board
@christiancacao99785 жыл бұрын
Is it bridgeable?
@andrasszabo73862 жыл бұрын
I have tried it is bridgeable.
@avrillavingedagotino7411 Жыл бұрын
Puedo conectar un ecualizador de tonos en donde dice R GND L?
@johnieleltitandelais6 жыл бұрын
Hi... can you make a review of the nost loudest 2" speaker and 2.5" speaker! Which one is the best!
@boomboxmaker726 жыл бұрын
Hey does amp make noise when volume is down like a hum? Am asking because a have one to it sounds great but it hums maybe mine is bad batch would appreciate response thank you
@als-techreview6 жыл бұрын
boomboxmaker72.. no mine is not noisy when is on low volume.. what kind of power supply do you have?
@bharathg80726 жыл бұрын
How is the bass
@vito_pito1o1756 жыл бұрын
Does it have bass?
@tlrautomotive84104 жыл бұрын
Can it handle 26v
@optimuscreation4 жыл бұрын
Hello when I bought my Bluetooth board The heat sink fell off what could I use to put it back on thank you
@karthikeyay29884 жыл бұрын
Put it back applying thermal paste with IC and apply glue to the side of the board NOT TO THE IC
@andrasszabo73862 жыл бұрын
On my version it is held on by 2 screws
@xNOFEARx585 жыл бұрын
Is there a on/off button ?
@als-techreview5 жыл бұрын
No.. there isn't any..
@bharathg80726 жыл бұрын
Can it support 2*80w at 6 ohm load?
@als-techreview6 жыл бұрын
of course it can support! myne speakers have the same spec! 80W / 6 Ohm
@kb_acoustics3 жыл бұрын
Odakle si?
@OrigMrElectric6 жыл бұрын
Hi! Did you run it with 12V or 24V?
@als-techreview6 жыл бұрын
Elektroskop Official.. here in this case on 12V.
@netrocker99904 жыл бұрын
This ic tpa 3116 D2, maximum output is 2*50w=100w. 120 w output is a hoax.They are cheating.
@revolution55474 жыл бұрын
They arent false advertising since the chip can do 120w at 10%thd+N but 50w*2 clean power