✅ BMW E46 Coding Airbag (SRS) ABG Module (Seat Occupation Sensor OFF)

[@craighoward9802]

The pregnant man is gone! :D Best video ever. I'm going to code out my sensor on my e85 Z4 rather than fit a bypass resistor/diode mod.

[@emanueliancu]

Man, I've been dealing with this for over 6 months and it's finally off. Thank you !

[@kovalveli]

thanks man ,great tutorial, the easiest one I have found so far.

[@Carterr]

Hello, thanks! Everything is right! But now after this operation, both airbags normally will works when car will be crashed?

[@e46.r]

Thanks guys! Works like a charm! 😉

[@drinkywinky5545]

Paldies par video🙂

[@CherryFarmEurope]

Thanks man , great video!

[@bluestack7889]

What cable to plug? OBD2? Thanks

[@norby93]

Hi,i did all the steps light goes out,but when i restart the car reapears, what i can doo?

[@Bimmerfanatic.]

Did you find out? Got the same issue at the moment.

[@paulsele2875]

I try for at least 3 days to figure out, you need to take out the sensor, or just unplug the 3 wire plug, reset the error cu inpa or ista. And it will work

[@Bimmerfanatic.]

Aight, gonna see if it works. Plugged the wire out. Got inpa.@@paulsele2875

[@Bimmerfanatic.]

@@paulsele2875 delete the code. Deleted the plug or wire. Its gone. But everytime i start the car its coming back.

[@dongalang1152]

Hi sir,we did it to my e46 facelift 2004 and it work perfectly,and when we try to other e46 which is e46 pre facelift 2001 and doesn’t work,can u advice me how to do it please,thank you sir

[@Sp3NgL3R_MF]

Hello, is it possible to reset SRS module when you had your airbag activated?

[@bluestack7889]

What about E87? It’s been quite difficult to get it working getting work with, but toolset32, INPA, and ISTA ok, just that NCS…. :(

[@karatist79]

латышок рулит йо йо LV! :)

[@rossienzo2126]

Hy your video is just crazy, thank you very much 🙏🙏 But i have got a little question, if my problem is on the "satellite front right", is it exactly the same manipulation, just disable this one with ncs expert and dummy ?? And me too i have to unplug the module for the seat ? Thank you for all If you have an answer for me it will be so great 🙏🙏 Have a nice day Enzo

[@pepecozmos8279]

And if u choose module this gives error no matter what u choose whats next?

[@TheJaanus25]

thanks in advance. please tell me where I can download them~~~~!!!!!

[@AM-uu2ho]

Great video thanks!

[@PEPEJONSON64]

Thanks a lot !!

[@szabolcsszekely7311]

I haven't got NCS dummy profile, which one choose?

[@eduardocrispin8837]

Thank youuuu !!!!!

[@injustice4566]

i would like disable pdc and break sensor

[@gavinviering4150]

Hi there! Not sure if you still monitor these comments, but I am attempting this various fix and need help asap! I am getting a vin faulty error even though it is entered correctly. I have a e46 bmw 330Ci with the Auto Transmission. The ecu model is the Seimens MS45.1. Please help!

[@ThatOneCatNyx]

You don't have to enter the VIN pretty sure (unless you aren't doing that and it is just NCS-expert being wack with its error codes). You may be able to select a different ECU under "Choose ECU". Try all of them- it may eventually work.

[@seattledjc3508]

I had this issue and it was fixed by switching the pin bridge on the cable

[@jesusfuenmayor7260]

528i, 2011 how to clear error.

[@prajuck1967]

No have AGB in box

[@XyberZyen]

pregnant man xD good une

[@abdullahessam9150]

Ty

[@alexj1757]

Will the airbag still work though?

[@modrix]

Yes

[@MindHunger]

PASoft is a lot easier to use.

[@gtalearntodrift]

Hi i received error when coding It says Error in CABD! Look at Cabi.err and error CC AUFTRAG: ERROR_ECU_PARAMETER_WRITE

[@matthewmicallef8287]

Did you solve it? I have the same error when coding out the seat belt pre tensioner. Thanks

[@gtalearntodrift]

@@matthewmicallef8287 I ended up code my airbag with PA Soft / BMW Scanner 1.4 it works perfectly

[@matthewmicallef8287]

@@gtalearntodrift I’ll probably end up doing the same. Thanks for the reply :)

[@Seth_41m]

​@@gtalearntodrift Hey there, did you had to bought a BMW Scanner cable to work with BMW Scanner or the K+DCAN cable can work with the software?

[@armaan9766]

@@matthewmicallef8287hey did you end up doing this? I’m having the same exact issue with seat belt tensioner