E46 Odometer Tamper Dot Fix: Light switch module VIN and mileage coding

How to fix and remove the odometer temper dot by recoding the LCM (light switch module) using BMW Scanner 1.4 cable and software.
IKE, LCM, FA, FGSTNR
Buy BMW Scanner 1.4 cable: www.ebay.com/sch/i.html?_from...
Buy Valve Spring Compressor Tool Kit for BMW N42/N46: bimmerzen.com/store
How to use the VSCT tool: • Using 3D printed tool ...
Fix oil consumption on BMW N42/N46: • BMW N42/N46 Valve Stem...
DISCLAIMER:
BimmerZen assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. BimmerZen recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of BimmerZen , no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not BimmerZen.

[@artiklo]

Single handedly the best instruction video on youtube. Clear, concise, to the point and step-by-step! Thank you.

[@radityarangga03]

Work's on my M43..Thanks for sharing! 👍🏾

[@Partatlan-fm7ks]

:)

[@mohammadbenattia9102]

Another useful tip, thank you

[@user-jl2we8zl4q]

Very helpful thank you

[@the_g371]

A quality content

[@NikolaHetfield11]

Thank you so much for all of your videos! Best on yt for sure! Can you please post video about correct procedure for coolant change and bleeding system on n42/n46 engine? It's different than other e46 engines, and almost all info on the net is about m52/m54 engines. :/

[@StephenPearman]

Hi, i‘m repairing a fire damaged E46 and have been supplied a used LCM, following your instructions to 1st check for correct algorithm in the support list, it only finds a partial algorithm match HC912-12 coloured in red and the part number is different, does this mean i cant match to the car.?

[@GaetanGASTELLU]

Hello, I would like to know if when we change a meter, we can no longer see the instant consumption, the time or the autonomy and is what it blocks the wheel to set the time. Thank you in advance.

[@Partatlan-fm7ks]

Üdv.Ez csak az újabb 35080 Eepromot tudja át írni vagy a régi 93s66 eepromos óracsoportot is?

[@DavidTavdgiridze]

I changed my dash on E46CI and left traction and brake check what can i do? I have this point and i think i must change the VIN like this? Can you reply me what can i do or can you help me any way thanks ❤

[@EweJinTee]

Hi. I have a different case. My LCM is at the correct Odometer reading but my IKE Cluster is not. Can I code it using your method but for the Cluster instead of the LCM?

[@carrimt]

Hello, just followed your post.. very much helpfull. I have the intrument cluster changed from the old owner, i was able to change the millage. The issue is that i cannot change the vin on the IKE. Its telling me that i need to factory reset before performing this action. The problem is that the factory reset is greyed out and cannot be click. Do you have any idea about this.

[@TheRodal7]

i have the same problem, did u find a solution?

[@Cars_Academy]

What if we changed the gauge cluster? Can you do another tutorial? Btw, very useful as always

[@MrMogulMoney]

Also would like to know this as well. Have a donor cluster with original LCM. Is software enough, or do we have to unsolder chip inside of cluster then reprogram?

[@gggobin8]

@bimmerzen, the link for the cable does not seem to work/list the part on eBay. Thanks

[@BimmerZen]

works normal for me..

[@alexanderchalichali735]

I need the valve stem seals tool kit removal im from zambia

[@BimmerZen]

I can ship to Zambia.

[@laur1sxd]

It will work on BMW E39?

[@BimmerZen]

I'm not 100% sure but I think it should be very simmilar.

[@smileylocz46]

Question real quick is it bad to just leave it and not reprogram it

[@major3913]

I have it on my 530d because the last owner change the odometer (crystal dead). I think it’s not serious

[@BimmerZen]

No problem at all.

[@major3913]

@@BimmerZen Hi, I have the same problem as you but in reverse, the previous owner changed the cluster because the crystals were broken, (fortunately the new cluster has the same mileage as the LCM at 1500km ready, I will write again the mileage on the cluster on the LCM) but my question is is it possible to write the VIN of the LCM on the new meter? Rather than the opposite as in the video.

[@strboy718]

So if I have an e46 and wanted to swap the cluster I can and the car will start with no issues?

[@Partatlan-fm7ks]

My cluster error: kzbin.info/www/bejne/m6WmmKtqeNx1iKs