BMW F10 550i n63tu Tmap 3.5 Sensor Upgrade

[@TinCanSailor]

Good stuff, props to the camera operator too!

[@samwlee6160]

Amazing video man thank you no body have your videos I got cold air Headers and jb4 now

[@KingofDHill2]

Just did mine thank you so much for this but man mine was hard to push in lol

[@JLaw1]

Clean fammmm 💪🏼

[@yodamel02]

Great video! Thank you. I have a question; there are (4) sensors on this motor. (2) on the intercoolers and (2) on the intake manifolds. did you not have to change the (2) sensors on the intake manifolds? I also have a tune from Mission, but have upgraded the turbo's to Pure Stage 1's so I'm thinking I need to upgrade all (4) sensors.

[@splittlive]

No just the Tmap in the inter oilers.

[@splittlive]

Sorry intercoolers.

[@yodamel02]

@@splittlive thank you for the reply. It's Mission Performance and they're telling me whenever they upgrade turbo's they replace all (4) sensors. They upgraded my tune to Stage 2 for the 3.5 MAP's and so far I got the ones on the intercoolers replaced, but can't get to the ones on the side of the manifolds. They are a PITA. tempted to just load the tune and see if it works ok as is, based on what you're telling me. ??

[@JimiJoey]

@@yodamel02Did you got all four of them swapped?

[@yodamel02]

@@JimiJoey Yes I did all MAP sensors Tuner (Mission Performance) told me that if I didn't do all 4, the ECU will still only max out at 21psi boost. I used a long extension and a swivel headed torx for the ones on the side (intake manifold) and worked from the top of the motor down the side. Took me about 5 hrs to do this job but I got them done!

[@MinorityProductions]

I’m curious about some of the settings you have on map6. From your later videos I realize you’re running map2 on the car with some duty bias adjustments. Does setting boost to 0 on map6 have anything to do with that? From what I understand, map2 has its own preset settings separate from map6. Just curiosity. I also own a 550i. Props on making videos btw. Definitely subscribed

[@qurantimes6705]

hi, where did you get the sensors from?

[@Urfavgirl_Avani]

Hey man love ur informative videos I had a question about the tmap sensors do I need to change them if I run a different stage 2 tune not using the jb4 at all I got the n63tu motor was thinking of going with bootmod3

[@og976]

It depends on how much boost your gonna run, not what tune you get.

[@lyndenfrazier129]

What does the bias setting do

[@michaelgarciapmc564]

Where did you buy the sensor from ? Can you send us a link ?

[@williamrivera5877]

Hey i have the same car as you and would like to do what you have done with the tmap sensors

[@xxkissit609]

So will this make your car faster running bm3 stage 1 tune thanks

[@BitcoinHakan]

You didn’t connect Maf sensors?

[@marclongshore8519]

Where did you get the upgraded t map sensors from?

[@jimsmith2383]

Are you going to do a Video on JB4 Tuning on a 2018 BMW M550i N63R G30?

[@meayman1]

do u have back end flash or only jb4 and bcm ? whats boost u are running ?

[@ryonmcgarrell7270]

Hi just want to know where you purchase the 3.5 TMAP sensor?

[@umbrellasolutionstech]

Prob fcpeuro or ecstuning

[@xxkissit609]

Do you need to install an intercooler with stage 1

[@t-drue327]

Hey will the Tmap 3.5 work on a N63 with a tune also and where can I pick up a set of 3.5 Tmaps

[@stevesibayan9493]

I have a2011 550i n63 jb4 type A connection, should I get the adapter for the sensors? It’s 129$ for the kit from BMS.

[@zachray5230]

What year is your 550i? Curious if the stock sensor is type a or b.

[@williamrivera5877]

Yes i have the same question

[@theromeeomtg9220]

Hey bro I change but I don’t have the Bluetooth on my jb4 it’s fine o I need do something ??

[@armandoelizarraraz2413]

Where did you get that intake set up? Got a video for them as well?

[@kevinkalil147]

I installed jb4 stage 1, just installed downpipes. I get bad exhaust smell. Should I upgrade to jb4-Bcm? How much boost should I be running with stage 1 and how much will I run with stage 2?

[@splittlive]

Kevin Kalil exhaust smell is from the deletion of the cats. However make sure your crush clamps are tight enough where the downpipes meet the exhaust. Your ECU should adjust for fuel.

[@kevinkalil147]

SPLITT MODS thanks for your reply. I replaced the stage 1 bms with a ecu tune stage 2. It regulated my fuel ratio and now the smell is almost gone and runs fine! I checked and running 17.8psi boost. Is that a good boost level? Can the car handle more?

[@sholderz]

Yes, 16' n63tu on 2.5 bar, catless, muffler delete, frt. grill intake & JB4 stage 2. Hit 22 psi and went to safe map 4. After 20 psi need 3.5 bar

[@mpgasperini22]

What intakes are you running?

[@TheKevinTran]

for Jb4 what harness type is require for your model ?

[@splittlive]

It’s the n63tu beta v.2.

[@VictorEstrada]

Do you really actually need the sensors? Can't imagine the n63tu running more than 42psi. How much boost is it running?

[@5ilentSavage]

How has the car been running with new map sensors

[@splittlive]

Car runs perfect, no difference except can run higher boost.

[@hasnainsheikh9154]

can you please send the link from where you got the tmap sensors from please. I have an N63TU as well and would like to install a jb4 bcm with the tmap sensors. Thanks

[@RT-qx7ts]

I have an N63. Where do I get the 3.5 sensors ? Do I need an adaptor?

[@NickyVlogs34]

Did you ever end up getting the tmap sensors and if so where from?

[@leonardomeola3900]

can you put the link where you got the TMAP sensor

[@ronaldo7289]

Burguermotorsport.com

[@jesuscosillos6646]

Hey bro where do you get these sensors?

[@ronaldo7289]

Burguermotorsport

[@stuartwest3822]

Before you put it all back together, test it

[@iDom215]

Price?

[@iDom215]

Are you going to go catless downpipes & upgrade the exhaust system?

[@splittlive]

$170 for both, but well worth it. Major gains running 25psi of boost.

[@splittlive]

Downpipes are next, I have them, just need to install. I’ll push out a 2 part video, part 1 ceramic coating, part 2 installation.

[@iDom215]

splittlive trust me I’m on the look out for that video! I bought downpipes from armmotorsports and haven’t installed them yet 🤦🏽‍♂️

[@joeys550iboosted8]

@@splittlive what duty bias settings do you have

[@mikailcrews2630]

Whats.your.whole Mod.set.up.cost.includi g.red.intakes And.what.will.this Install.do.4.my.2011.55.o.i.xdrive 👌 glue.trick.