BMW F650 Funduro Problem with Carb.

I had nothing but problems with my carbs on my BMW F650 Funduro 1996 model. I ordered a repair kit that came with jets, o-rings and gaskets but since adding it all nothing but problems.
Eventually decided to strip it all back again and take a good look. Found out that these kits you can buy are rubbish. Different sized jets than originals and I even ordered another that arrived the same, different sizes and not consistent at all. My advice don't buy a cheap one!
In this video I show how to remove the tank and panels etc, plus removing and replacing the carbs. The bike now runs fine again :-)

[@hdbkfl]

Sir. You are the man! I have always been intimated by even touching a calburator, but you made it look easy. Thank you for making my quality of life better! Thank you, thank you..

[@bezpopisu]

Finally I found out, which float mount in which carb - I spoke about the jet in the plastic float funnel. Thank you!

[@howrrmr.7172]

Happy 2023 with your 650!!

[@richardwhitehead4684]

Not having a garage, I also have to work in an old barn. Not ideal, but better than working outside. Fwiw, I just purchased a non running 1997 f650 and will pulling the carbs soon.

[@motoarchery]

Wooowww. I got lost in that carburetor with ya, mate. Motorcycle bliss. My 99 f650 is still going strong, but she's lately been chugging a bit at lower rpms. I know its time to get down to that carb. Thanks for the excellent video.

[@GreggBennett-j3p]

It’s a lot cleaner than the turd infested barn I have to work on my bikes in. And the critters (woodchucks and squirrels) will chew on the rubber stuff. Ugh. But like another commenter said, it’s better than working outside…

[@gerard3665]

Thanks for the video. You are a good mechanic. You don't clean the carburettors with ultrasounds and you don't do the synchronization with a special tool ? It is not necessary !

[@DJPresser]

If you have an ultrasonic cleaner then yes do it! For balancing the carbs I just listen and ride until I’m happy.

[@rangie944]

Thanks for posting, good information there thanks. Did you change the venturi in the carbs?

[@DJPresser]

No, didn't need to so left it alone 🙂

[@pawekaminski7607]

Thanks for the movie. Wondered what is correct position of this short cable with a spring that opposes the throtle cable at the left side of carburetor. I have turned it one way and the other and don't know how it should sit now.

[@elioresmini6339]

Hello, I have a consomation of 10l/100 with my f650 75km. Is it a carb problem for sur ? Thank you

[@DJPresser]

Check to see if your carb is overflowing when you leave the fuel tap on. If yes then the floats are not working as they should.

[@alexbombana3344]

Ciao la mia a cominciato oggi a strappare e nel mollare lacceleratore scoppietta cosa potrebbe essere ? Forse candele o filtro benzina 😅?

[@DJPresser]

What value is your idle set at? it should be about 1200 revs

[@Creative-content24-7]

How many turns out is it on the air mixture screws pal thanks

[@DJPresser]

I did 3 turns out. You can get to it once it's fitted back in if you hold your tongue in the right place!

[@Creative-content24-7]

@@DJPresser I did 3 and half and just left it mate surly will be ok

[@TINGVELL]

did you try it out how was it

[@DJPresser]

Worked a treat thanks

[@PeterSmith-or3pq]

I've done this on my 98 f650 st . Little tricky ❤