BMW FRM3 footwell module recovery repair with orange5

[@tel200]

Hell, your 🍊 Orange-5 has had a hard life Nice job on the FRM 😎

[@ecurepair]

This ones had a hard 6 year life for sure. Love orange5 but wish they used an aluminum case. I have a tendency to use hot air on it. The kapton tape helps a bit. I have my tl866 wrapped up with it as well.

[@lattehour]

can you make a video about the programmers you use why and what for x job ?

[@ecurepair]

Thanks for the suggestion, I'll keep it in mind.

[@dashtyATG]

Thank you very much for your video. But the Font size or the format was very small couldn't see the screen at all. I'm about to get the orange tool as I'm a locksmith and do have a lot of great tools including ms909.

[@ecurepair]

Its a good tool

[@Fabi....]

Hi. I heard about this glitch but haven't fixed it yet. Regards.

[@e36_agd16]

Thank you so much, helped me a lot ❤

[@mitumkallidin3464]

Good day sir, what happens if the Dflash theres no info and EEE but Pflash is available is there a way to save for example a bcm that got corrupted, i was working on a Jaguar xf 2013 after battery removed it corrupted the front BCM

[@ecurepair]

For bmw if there is no dflash you have to use a known good dflash from another module and then code the unit same as you would a replacement. I dont know much about Jags but I assume it would be the same.

[@mitumkallidin3464]

Thank you very much, really appreciate your feedback 🙏

[@saidboussouf7059]

hello friend es-que when you write eee and pflash es-que you also have to reprogram the dflash or you don't touch it

[@ecurepair]

Writing is just pflash and eeprom. No dflash.

[@germany4650]

does it work with a dongle or can it be done without?

[@ecurepair]

Does what work with a dongle?

[@germany4650]

@@ecurepair I don’t know what’s in the key or not, it’s just supposed to work with the key, but they didn’t send me with the device

[@rodskietechtv1296]

can this programmer support renesas RL78 mcu?

[@ecurepair]

it has some in the list yes. i have not tried those with it though i dont think

[@saidboussouf7059]

Bonjour pouvez vous mettre les pin avec orange5 merci

[@ecurepair]

as connected in video: #1 purple wire = vcc #2 yelllow wire = rst #3 black wire = gnd #4 green wire = rxd

[@saidboussouf7059]

​Thanks you

[@rodskietechtv1296]

what is the software name and where can i get? i want to buy the programmer like you are using...

[@ecurepair]

I use xprog from www.eldb.eu and orang5 from www.scorpio-lk.com/orange5.html

[@florian2050]

Why you delete pflash? its enough to write dflash to eee

[@ecurepair]

I think orange5 was being picky on that one for some reason and wasn't writing correctly till I cleared it all. I usually use xprog on them so cant recall at the moment why I had to when doing this video sorry.

[@namechane1758]

why did you make this video and not clearly show where the wire plug in the orange 5? Not to mention as you jumping around with the pins and skip saying the name of what you're plugging in? Seems obvious to focus a little bit on the actual connection. Then you open the software and say "Let's go into 'device''" and you clearly clicked "type" Why make a video, that should informative, and make no effort to avoid confusing people?

[@ecurepair]

I do call out each pin as I connect it. VCC, RST, BKDG=RXD and Ground. They are what they are. As for saying Device and clicking "type" I use a lot of tools. These are generic terms for going into the software and selecting the chip you will be reading. TYPE is short for TYPE OF DEVICE.

[@JP-hm7jw]

hextag best for these and many other modules

[@ecurepair]

Its not hard to do it with any tool that works with 9s12xeq384. Hexprog does have a nice dummy button to do everything for you it looks like which can make things easy. Personally I havent used it so I cant comment much on it. Thanks for watching.

[@saidboussouf7059]

another question is it necessary to program the dflash after eee and the pflash

[@Picdev-z6l]

Where you can find tutorials about the calculator procedure of orange5 ?