NICHT UBER MAX: we show you how to install all the clutch parts on an S 1000 RR. It's easier than you think!
Пікірлер: 31
@andreasdrz10845 жыл бұрын
Real proffesional, mechanic, one of the hardest tasks for a bike, cause needs knowledge of what you are doing, plus doing it correctly. Precise and easy touch for this kind of task, cause if you miss the allignement or the order of the disks, then goodbye them and go for a new pack...
@PaulSmith-ck8lz Жыл бұрын
Did you replace the outer basket? And why?
@philbroom4711 Жыл бұрын
Helpful video thanks . Trouble shooting my same clutch , with cover off if you pull the clutch the outer basket slightly moves before the clutch engages , should there be play ?
@BMWMOAorg Жыл бұрын
A small bit, but not much. Refer to a technical manual to be 100% sure.
@dzachalski5 жыл бұрын
Before you take it apart do you need to line anything up like put it in neutral, gearing , etc ?
@BMWMOAorg3 жыл бұрын
no, but everything has to be lined up and locked (as needed) before reassembly
@KeuleHamburg19852 жыл бұрын
Hi, what part number does the steel block disc have ? Same needed for the pin tool and nut which gets 150 Nm ... thx in advance
@BMWMOAorg2 жыл бұрын
We recommend looking up part numbers on one of the parts fiche sites on the web - I use shop.maxbmw.com/fiche/PartsFiche.aspx a lot - because p/ns can vary depending on model & trim level.
@mijingboro33373 жыл бұрын
nice
@skyline17397 жыл бұрын
What about that center adjustment screw in the basket?
@BMWMOAorg3 жыл бұрын
Try this resource: www.s1000rrforum.com/threads/torque-specs.2873/
@babarjunejo70854 жыл бұрын
Hello sir .. I have same bike and the issue is my Bike's oil pump chain is very loose.. can you please guide how can I adjust it.. bocoz there no workshop or a good mechanic here. I am in north africa.
@BMWMOAorg3 жыл бұрын
haven't done that job yet, Babar - sorry I can't help you (yet)
@BniMafiaClick8 ай бұрын
I did the same job but I had no pressure on the clutch lever. What do I have to do?
@philbroom47117 ай бұрын
I’d say adjust starting at the push pin then to arm and then lever last
@MrBoomtheroom2 жыл бұрын
where can you buy the holding tool from?
@BMWMOAorg2 жыл бұрын
Check with your BMW dealer; if they don't have it, Wunderlich might.
@nealekerr72535 жыл бұрын
What torc setting are the spring bolts at the end set at?
@BMWMOAorg3 жыл бұрын
Try this resource: www.s1000rrforum.com/threads/torque-specs.2873/
@YoungBossSteppa3 жыл бұрын
Do i need to drain the oil? B4
@BMWMOAorg3 жыл бұрын
NEED to? No. Draining the oil will make the job less messy, though!
@thisisrodwheeliemaniac92226 жыл бұрын
how many ODO km for clutch replacement ??
@lamsgt145 жыл бұрын
my XR has 40k km on still running the stock plates...
@LilWaynEE715 жыл бұрын
aong kittisu I am going to change my s1000rr 2017 and have 22k miles on mjne
@LilWaynEE715 жыл бұрын
Lots of wheelies
@BMWMOAorg3 жыл бұрын
Depends on the rider and conditions. Somebody who races will need to replace the clutch sooner than somebody who doesn't, for example.
@kaspik817 жыл бұрын
16:50 - the recesses of all the friction plates must be are in line. See in repairs manual.