Keep these coming! I’m rebuilding a similar engine right now so these videos have been helpful. The 40 is looking good.
@medicinaljourney55055 ай бұрын
Great video. Very informative and clear. KZbin needs more content like this.
@lelandwilliams26767 ай бұрын
Thank you. I am currently working on a 2007 50 hp EFI 4 stroke. It ran for 20 minutes, then VST output pressure dropped to 2psi and jumped back up to 43psi. It did it two more times them shut off.
@bouldernelsonbigfoot2 жыл бұрын
great vid
@meddahismail97534 ай бұрын
Merci beaucoup ❤
@lelandwilliams26767 ай бұрын
I also ordered a new low pressure pump as well
@TheBoxingTrainersChannelАй бұрын
Is it normally the fuel pump when at first the boat starts up, but after you let it run then cut it off then it won’t start back up?
@JimmySaguiped Жыл бұрын
Good morning sir.... Can you to tell me where to buy those replacement kit of fuel pump.. mine is 75hp mercury looks the same from what you have on your demo clip... Please
@tfrantastic2 жыл бұрын
Any reason to rebuild this if there is no issue?
@robnall3483 Жыл бұрын
I have a fuel pump off of a 1995 two-stroke 60 hp mercury order a new kit for the pump. It came with two clear nylon check valves and two rubber ones, the original carburetor but I took it off. Did not have the rubber in it can I still use it And combination. Thanks.
@bbreede1 Жыл бұрын
I could not get the center pins to push in at all for the check valves. It wouldn't go in at all and broke off. I couldn't really get the other one to move either before I even insert it. I was just checking it after I broke the first one and it wouldn't move down before I even put in the pump.
@ethanlocke63318 ай бұрын
It has triangles to line up and when you were stacking it to reassemble you started upside down. I knew immediately that spring was gonna give you troubles.
@NinoSpinner Жыл бұрын
Vorrei montare una pompa su un fuoribordo Mercury 3.5 su cui è presente solo il serbatoio incorporato Vorrei dunque installare una pompa benzina da collegare ad un serbatoio esterno Che tipo di pompa posso montare? C'è qualche cosa da sapere prima di acquistarne una adeguata? Grazie
@lelandwilliams26767 ай бұрын
The pump in the VST looks good, no real dirt, so I'm going to replace the pump
@brunocauin Жыл бұрын
Is there a way to upgrade these to an electric pump? I rebuilt mine, installed all new lines and filter but can't seem to get enough fuel pressure...
@blakedarnell84625 ай бұрын
My ‘94 tracker 40 doesn’t have the vacuum hose coming out of the front. Does anyone know if that’s common with older 2-strokes? Seems like all the replacement pumps online have the elbow fitting coming out of the front (vacuum hole)… Just pipe plug the hole and move on or what?
@TERRYSMITH-vu6er Жыл бұрын
I HAVE A 50 HP MERCURY 2 STROKE THAT ALL OF SUDDEN LOCKED UP I PUT A NEW STARTER/SOLINOID BEFORE THEN IT WAS TURNING OVER GOOD ANY IDEAS
@danielguerra626 Жыл бұрын
Can you do a video on a Mercury V6 carb rebuild?
@upinstylesalon Жыл бұрын
I have it all done. Took it off last year and now I have forgotten where the lines from it go :( I have pictures of mine.
@ayhankucukozer14789 ай бұрын
Mercury 50 hp marine engine fuel is not coming to the spark plugs. I am thinking. injectors are solid. ecu is solid. When you add a few drops of gasoline into the cylinders, the engine starts and then stops. Cylinder pressure is very good. When you press the starter to start the engine, oily gasoline comes out of the exhaust. Can you help me? Also, there are syringes inside the log. I don't understand what they do. Greetings from Turkey.
@martinpescador1289 Жыл бұрын
Ótimo vídeo parabéns (Brazil)
@harrytselios42282 жыл бұрын
Wondering why newer motors have more engine block failures than the older engines?
@dupontpascal15268 ай бұрын
merci a vous
@bigl2thad2005 Жыл бұрын
Your suppose to line up the triangles on the fuel pump housing and gaskets together. No need to mark it. You gave it flipped on one end sir.
@daveskura7 ай бұрын
great video
@garneroutlaw1 Жыл бұрын
Great video, but the manual says to break it off prior to pushing the pin in, not after seating the pin. It seated as intended in this video. There is not supposed to be anything to break or snip off.
@Shoot_and_Scoot Жыл бұрын
That’s cool, if you guys would send me my fuel pump rebuild kit I ordered two weeks ago I could rebuild my fuel pump too….