If you've got a few longer bolts with the same thread, cut the heads off and thread them into the holes. Then slide your sump on using the bolts as a guide, it then lines up perfectly first time. Get a few standard bolts in, then remove the long ones :)
@BAYERNEMPIRE7 жыл бұрын
I don't know what car this was, but all I can say is that you are truly a genuine caring human being. Man you have so much life and maxi. Good on you. It is very neat to see someone as happy in what you do in life as you are! I hope all is well Mike
@roybatty203026 күн бұрын
Great video from a smart mechanic, thanks!
@MrGammyballz3 жыл бұрын
Watched your 4 part guide and just changed bearings and cleaned sump/strainer. Excellent videos and the job was a doddle! Thank you very much 👍🏼
@bodgitandleggitgarage3 жыл бұрын
Glad it helped
@cmcquaigue9 жыл бұрын
Thanks so much - feeling good about tackling the big end shells now - your videos certainly help to build my confidence, thanks again!!!
@bodgitandleggitgarage9 жыл бұрын
Chris McQuaigue any time mate thanks
@ineeddollars5 жыл бұрын
Very good information, No crappy adds here ,
@bodgitandleggitgarage5 жыл бұрын
thanks mate
@dereksteele18669 жыл бұрын
very well explained and u make it look so easy many thanks
@bodgitandleggitgarage9 жыл бұрын
derek steele thanks mate
@peterr33347 жыл бұрын
It is a very good and useful video. Our POLO 1.4 from 2002 has the same oil pan. THANK YOU for showing how to put in the 2 screws into the deep holes next to the transmission. It was a horrible job for me. I could put into their place only one of them, hopefully it is not a problem. Maybe next time it will be in my garage I will try again.
@bodgitandleggitgarage7 жыл бұрын
Péter R glad I can help mate thanks for watching
@peterr33347 жыл бұрын
Do you think that it could cause any problem if one screw is missing?
@bodgitandleggitgarage7 жыл бұрын
Péter R I no people that have left both of them bolts out and have no problem
@peterr33347 жыл бұрын
Thanks.
@gabrielbaum96608 жыл бұрын
awesome bit of work and advice pal ,proper english and well explained. gonna have a go on my Vectra C 1.8 petrol hopefully i can leave exhaust in too. all the best from Nottingham.
@bodgitandleggitgarage8 жыл бұрын
thanks mate and thanks for watching glad you enjoyed it
@derbynalfreton7 жыл бұрын
Easy on a vectra c 1.8👍🏻
@BillSikes.6 жыл бұрын
Cheers fella I watched both these videos and the tips you provide are a real godsend, good day bro :)
@bodgitandleggitgarage6 жыл бұрын
glad it help you mate
@jjtaylor788 жыл бұрын
You're ace man, identical to ma Audi A3 engine. Wish I'd watched this video before is tried to get them 'nightmare' bolts out!! All done now tho, well done :)
@bodgitandleggitgarage8 жыл бұрын
+JJ Taylor thanks mate and thanks for watching
@scottaner5009 жыл бұрын
reley good vid proper old school garge way of doing stuff like that
@bodgitandleggitgarage9 жыл бұрын
***** thanks mate
@brianmilligan1787 Жыл бұрын
Why don't you just remove the obsticle being the exhaust That's lash loads on and when you tighten the sealant will squeeze inwards creating a silicone rope that will loosen into the sump eventually getting sucked into the strainer oil lifter causing oil starvation hence waste of time blown engine never mind you struggling with sump round exhaust removing sealant from an area that you never noticed causing a leak later some pressure builds up in the sump
@davidnelson43107 жыл бұрын
thank you my friend nice description of how to do it
@bodgitandleggitgarage7 жыл бұрын
David Nelson thanks a lot and thanks for watching much appreciated
@oliverjohnston36482 жыл бұрын
That is an excellent video.
@davidrees5544 Жыл бұрын
The sump screws at the gearbox end are a problem to remove. The ball-head Allen key is not working, and the gearbox to block plate/gasket is in the way of a 'straight' Allen key. tips and tricks are welcome. I'm close to cutting the sump into bits
@hmdigiart78573 жыл бұрын
great video, great job. Incidently how much would it cost to have a front lower sump repaired? Thanks
@etzilla9 жыл бұрын
thanks for sharing. What is the timeschedule when the sealer is on?
@hectorgacha60545 жыл бұрын
Hi you did a good job but personally i would take exhaust off to make sure it’s out of way as you took a few bolts off a couple more won’t hurt
@bodgitandleggitgarage5 жыл бұрын
You are forgetting an important parts when I tell the customer the price for the job and then if I take off especially exhaust bolts if things start breaking and the price goes up the customer is not very happy in the real world I know what you are saying but it doesn't always work out that way practical how would you feel if someone gave you a price and gave you a call and the price tripled
@Dl33ter2 жыл бұрын
Thanks mate !🤘
@nevenmajetic19712 жыл бұрын
Nice..Thanks you..
@lucianoaliquo66293 жыл бұрын
Here is a tip, just drop the exhaust it's only a couple of bolts and makes it much easier
@bodgitandleggitgarage3 жыл бұрын
In a perfect world yes but not in the real world when the bolts are really rusty and it causes you hours upon hours to draw them out to replace them
@lucianoaliquo66293 жыл бұрын
@@bodgitandleggitgarage use a blow torch heat the bolts spray with oil wait 10 min and remove
@bodgitandleggitgarage3 жыл бұрын
@@lucianoaliquo6629 🤣🤣🤣🤣🤣 ok I really dont understand why any bolt in the world ever get snapped them because your method must work every single time
@lucianoaliquo66293 жыл бұрын
@@bodgitandleggitgarage works for exhaust bolts they used to the heat 🔥 not trying to be funny mine worked much easier with the exhaust removed 🙏
@bodgitandleggitgarage3 жыл бұрын
@@lucianoaliquo6629 It will only work when the bolt is full and not rusty In 90% of the cases because the Goes through multiple heat cycles The boat just rusts away And goes very weak And then just snaps off if you have done any amount of cars what's the weather you would know this I have done Multiple video showing exhaust bolts and what happens to them Any experience mechanical know this
@MoMo-vv4lt4 жыл бұрын
Thanks boss
@stephenbowden60979 жыл бұрын
Could you please tell me how to turn a engine by hand that is all seized up please
@bodgitandleggitgarage9 жыл бұрын
Hi mate if the engine is seized there is no way to turn it check the big end bearings first there's two bolts for each person disconnect all bolts and then try and turn it if the engine turns when you have a problem your big end bearings unfortunate your engine is seized it can be very expensive to sort out
@jjtaylor788 жыл бұрын
As a note, I never replaced those two difficult bolts cos didn't wanna risk losing them into the clutch housing. 48 hours later and it's still dry as a bone underneath. Not a drop of oil coming out! 😊
@nsoper196 жыл бұрын
I've got the 1.6l fsi engine. can the sump be removed without taking off the exhaust on that model too?
@bodgitandleggitgarage6 жыл бұрын
Nathan Soper if your exhaust goes underneath the sump then yes it will get in the way and take some of the sealer off and it will leak just easier to take it off but just be careful as you can snap bolts you're damned if you do and your damned if you don't
@colinhoward27805 жыл бұрын
You need to come and sort my golf out pleeeeeeeease lol 😂
@bodgitandleggitgarage5 жыл бұрын
lol
@colinhoward27805 жыл бұрын
I am being 100% serious Come to the uk and sort my vw golf out it needs a pro to working on it
@paulMason-zm4kr7 жыл бұрын
hi on a z16xep 1.6 twinport astra sump is it the same to seal it and also on the side that goes onto the clutch gearbox side do I put a bit of sealer on there also as I totally cleaned my sump in and out and there was a bit of sealer on it when I removed it is have Loctite 5920 copper silicone high temperature is that OK to use 1 more thing my low level oil sensor broke so I got another one but the cable inside the sump is a bit smaller than needed to get it to sit on correct bracket if I cut the cable and extend it enough what can I use to seal the cable and cover it to protect it from the oil and temperature it will be inside the sump I thought of using heat shrink but don't know what kind I need I only have to extend it a inch rather than spending £70 on another sensors if safe to do so thanks
@bodgitandleggitgarage7 жыл бұрын
paul mason hi mate as long as you feel what was originally sealed make sure everything is nice and clean you will not have a problem as your regards you're sensor you will have to buy the proper one for it I don't know of anything you can use to seal it if you cut it eventually even if you manage to seal it will not last by the proper want you will have no problem
@paulMason-zm4kr7 жыл бұрын
bodgit and leggit garage thanks il get a new one ordered and seal the sump how it was thanks for getting back to me
@bodgitandleggitgarage7 жыл бұрын
paul mason anytime mate glad I could help have fun with it
@bodgitandleggitgarage7 жыл бұрын
paul mason anytime mate glad I can help
@donanwaarkhan67546 жыл бұрын
Where can I get this dirko Garu from in Uk 🤷♂️
@joestubbs31386 жыл бұрын
can you please recommend a sealant...joe
@bodgitandleggitgarage6 жыл бұрын
Joe Stubbs 4:29
@rob87587 жыл бұрын
is it not easier to just take off the exhaust?
@bodgitandleggitgarage7 жыл бұрын
Robert Wiliams no risk snap in the exhaust bolts causing the customer triple the cost so no it's not worth it
@bodgitandleggitgarage7 жыл бұрын
Robert Wiliams no risk snap in the exhaust bolts causing the customer triple the cost so no it's not worth it
@rob87587 жыл бұрын
Ah ok that's fair enough. I'd be doing it on axle stands so I dno if I'll have enough room. Also I read somewhere about disconnecting a drive shaft for some reason. Doesn't look as though you need to.
@dannywood68427 жыл бұрын
Just do it properly, it saves time and effort.
@bodgitandleggitgarage7 жыл бұрын
i did it properly
@GymChess7 жыл бұрын
How much crap is usually in the sump or is it generally quite clean?
@bodgitandleggitgarage7 жыл бұрын
GymChess hi mate if you change your oil regularly it should be really clean did you got a lot of slugs and stuff it means that all has not been change regulate
@ionutmihailescu95615 жыл бұрын
Se sudeaza baia de ulei la tuoran cine stie...
@ionutery4 жыл бұрын
Depinde.... Cat de mare este fisura?
@steliandaraban94553 жыл бұрын
@@ionutery La Golf 4,Diesel baia e din Aluminiu, picură puțin. Se poate repara?
@ionutery3 жыл бұрын
@@steliandaraban9455 Trebuie găsit meseriaş bun care a mai sudat, altfel iese cârpeală şi mai bine cauți una în dezmembrări şi o montezi tu dacă ai un minim de scule si habar....
@unda256 жыл бұрын
If you take out clean it properly .is just a English way to do it is not proper 1000 Percent is like 95% ... How much you charge for that .I pay today 100 pounds only labour I provide meself oil and new filter