2007 Toyota Auris Back Discs And Pads Bodgit And Leggit Garage

[@MrPaul278]

When winding back the piston, the bleed nipple should be open and a pipe fitted to collect the fluid. This should prevent damage to the square backed piston seal from being damaged. Also pads with backing should not be greased as this can damage the backing liner in some cases, the fitting instructions will give advice. Remember to adjust the handbrake afterwards. Good videos, I hope this helps some of the readers,

[@bodgitandleggitgarage]

Paul Jeffreys the only thing I agree with you is about tightening the handbrake afterwards on certain vehicles but when you whine back the piston the handbrake adjusts on some vehicles so it's not an issue I've been doing this for years and know people that been doing it for longer than I've been alive never once had a problem pushing back the piston

[@OneAuto]

Like me 🤗

[@bodgitandleggitgarage]

One Auto, lol yes Rob maybe we should go and look at his videos to see how we've been doing it wrong for so many years r no wait no video

[@hardworker8030]

bodgit is to young to know that years ago the seals in the master cylinder was turning over when you pushed back the pistons. This is why so many cars was having the foot pedal go down to the floor when driving.

[@bodgitandleggitgarage]

Hard Worker lol I'll leave the response to Rob🤣🤣🤣

[@lukey3507]

Hi Leon, on the drivers side on these Auris's, does the drivers rear caliper retract the opposite way? The passenger one is clockwise piston going in and the drivers is anticlockwise going in.

[@brendo3314]

Every time you watch one of your videos you bring something new to it well done best show in town

[@bodgitandleggitgarage]

Brendo thanks mate

[@stuzman52]

Fantastic video Leon with great explanation throughout the whole job. I'm quite sure this video will help a lot of people out there. 😀👍

[@bodgitandleggitgarage]

stuzman thanks Terry very much appreciated thanks for popping

[@davidlink2861]

Great Vid, just what I was looking for, but can you confirm what direction the off side piston retracts in? Thanks

[@bodgitandleggitgarage]

clockwise mate

[@freddesgarage]

Hi! Is it the same way you'd turn the piston in,,clockwise,on the left side on 2018 Auris? //Fredde

[@bodgitandleggitgarage]

Yes Mate you turn most engines that way

[@freddesgarage]

@@bodgitandleggitgarage thanx sir 👍

[@wyattoneable]

Boom! That disc has been wasted. That's a handy tool to depress the plunger. Nice Thomas tattoo and nice job explaining the job.

[@bodgitandleggitgarage]

wyattoneable thanks mate yes the right tool for the right job makes everything a lot easier Thomas tattoos going to be on everybody it's going to take over the world hahah

[@scon2006]

Any tips on how to tell if it left or right wind back calliper, I know some have an arrow but some have nothing

[@bodgitandleggitgarage]

Misfit drifters hi mate the only one that comes to mind is the Renault Master van you can't really do any damage if you get it wrong it just will not go back in you'll see it come out then just turn it the other way

[@bryier]

great video now can I adjust handbrake on my Auris its 2008 model??

[@bodgitandleggitgarage]

Hi mate the first of judgement you need to do is at the brake shoes against the drums and in the second adjustment you can do is at the handbrake cable but just make sure your handbrake cables are not stretched

[@anthonychristodoulatos6094]

Thanks for the molly grease tip 👍

[@evieemaya88]

Great videos keep them coming. Off topic but with oil changes what do you think of those 12v oil pump extractors? For or against?

[@bodgitandleggitgarage]

Arts&Trusts hi mate I've often used the 12 volts oil extractor you're safe on my video and especially for the newer cars with the plastic sump I have no problem in using them at all as long as you heat the engine oil to make sure it flows easier

[@jahmercymackintosh3898]

Great job. Can the car be on hand brake while the job is going on?

[@bodgitandleggitgarage]

Hi mate no because you want to test to make sure there's no binding as you are doing it if the handbrake is on issues inside will be on and you will not be able to turn it freely so you won't know if you have an issue

[@zedman442]

Nice. What lamp is that? You had a real thin style inspection lamp. What brand was that?

[@bodgitandleggitgarage]

Zed Man hi mate that is a Snap-on stylus smart light

[@TheDisgruntledMechanic]

Always fun some of the things that are found can be so interesting!

[@bodgitandleggitgarage]

The Disgruntled Mechanic the joys of being a mechanic lol

[@brendanbradyfan02]

From your videos it seems Toyota is popular in Ireland I'm guessing they don't like cars that go wrong very often so they play safe and reliable 👍🏻

[@bodgitandleggitgarage]

Brendan Brady fan they still have lots of problems mate

[@bodgitandleggitgarage]

But yes would be one of the top three ford Toyota Volkswagen

[@brendanbradyfan02]

bodgit and leggit garage interesting choice for the Irish,everyone makes out that Toyota is so reliable but I'm sure you've seen all sorts go wrong on each brand

[@franklane6557]

Thanks for the video,yes Toyota do have their own problems and they are not a cheap fix.

[@shishuali4821]

the grunt! I love it, who needs a torque wrench 😄

[@bodgitandleggitgarage]

Shishu Ali exactly mate lol

[@JamesPropmaker]

I have more phone data Another great video.. Still waiting to her about my new workshop

[@bodgitandleggitgarage]

Jamesmachinery sounds nice new workshop hope to see more videos mate

[@EXOVCDS]

Steven's totally ignoring you... did you guys have another fight? Is he jelous of your exovcds tattoo? Give him one of my stickers! =)

[@bodgitandleggitgarage]

Thomas EXOVCDS lol

[@mornefourie8842]

Very helpful. And accurate.

[@bodgitandleggitgarage]

Thanks mate

[@OneAuto]

That's a fancy brake wind back tool. Is it made by Spikes Pivalance? 😂😂

[@bodgitandleggitgarage]

One Auto, haha no mate this is the new fancy beta one

[@K_N_44]

The one caliper was clockwise and the other was anticlockwise. Is this normal?

[@bodgitandleggitgarage]

yes some cars that is how they work some cars don't

[@K_N_44]

@@bodgitandleggitgarage okay thanks mate . The car is also an Auris 2009

[@franklane6557]

Great video thanks.Could you do a video on changing the fuel filter on a diesel auris 07-09 model.Many thanks.

[@bodgitandleggitgarage]

as soon as i get 1in i will mate

[@robinsonsauto]

Fantastic video lion

[@robinsonsauto]

Lion

[@robinsonsauto]

Leon darn auto incorrect 😂

[@bodgitandleggitgarage]

robinsonsauto lol I've been called worse and lion is very manly so I don't care lol

[@ozzstars_cars]

Nice job with the video

[@bodgitandleggitgarage]

Ozzstar thanks Glen

[@vdubs6068]

Great vid Leon Cheers Jamie

[@bodgitandleggitgarage]

Vdubs 60 thanks mate

[@michaelmcdonagh4651]

I got both front and back brake pads and disc done on Toyota auris 2007 failed test because of brake imbalance why is this

[@bodgitandleggitgarage]

hi mate it could be a couple of things maybe one of the brake pads on sitting in properly maybe you've got a lot of rust around the caliper and carrier and they are sitting in properly also the caliper could be slightly seized also you could have a bit of air in your system unfortunately is a few things you'll have to go through everything step-by-step if you've got really old brake fluid in your car your best replacing it as it could be contaminated with water

[@TerryD15]

T remove a really stuck disc there is a threaded hole between the studs, I htink that it's M8. screw a bolt in there and Bob's yer uncle it will pop off

[@RamLakhan-101]

Hi, why do the piston holes have to be aligned with the notches on the brake pad? What happens if they aren't? Another thing.... Sometimes my handbrake goes up 3 notches sometimes 5....what is up? I've got new rear discs pads and handbrake cables are only 3 mnths old. Thanks. Oh... And refurbed brake calipers!

[@bodgitandleggitgarage]

hi mate it doesn't have to necessarily lineup just as long as it doesn't hit the little nipple sticking out of the brake pad this will cause the brake pad to wear unevenly and the piston not to to apply even pressure on the brake pad

[@hardworker8030]

Why does the sliders have rubbers seals on them.

[@bodgitandleggitgarage]

Hard Worker it is so they don't get covered in bits of crap which will cause them to seize and not slide properly

[@hardworker8030]

I mean the rubber on the end of the actual slider pin and not the dust cover.

[@rock1richful]

Super Leon

[@bodgitandleggitgarage]

Roc Dogg thanks mate

[@paulmayou370]

great part 2

[@bodgitandleggitgarage]

thanks mate

[@robc5955]

Ooo jealous of that wind back tool, the spanner one I’ve got is a pita cause you got to try and hold the Caliper etc, also slight correction I think the medium grunt for the carrier bolts should have been an ooof ya twat surely? 🤣 I say that for all the k nobs who say, oooo u don’t want do it like that, no no no, you wanna do like this... jeees, anyway another great video I’m addicted to these.

[@bodgitandleggitgarage]

hahahaha thanks mate

[@simonrawle7885]

im guilty of forgetting to pump the brakes . come to the first junction realise i forgot and stamp the peddle 5 times in a row like a mad man

[@bodgitandleggitgarage]

Simon Rawle lol could have been a lot worse mate at least you managed to stop

[@stevejones8665]

Hahahaha I was once in an old Series 2 Landrover going down a 1:6 Hill and when my brother in law hit the brakes nothing happened then he pulled the Hand brake which on those old Landrovers is a transmission lock Geez we almost went thru the windscreen lol at least it taught him to always pump the breaks after working on them.

[@ukmud6218]

can I buy grunts at halfords?

[@bodgitandleggitgarage]

Uk Mud no you can get them from my website lol just 1 million pounds each cheap I think

[@stevejones8665]

bodgit and leggit garage Hahaha Grunts beat any Torque wrench lol I watched a Posh American you tuber using a brand new torque wrench on 10mm Ducati Motorbike bolts he sheared about 3 off before working out the difference between foot pounds and Nmtrs LOL i pmsl at him lol Now if only he used a little grunt with a small spanner Sorted...He also drilled thru the Plastic Ducati Petrol tank so blooming funny he will never make a mechanic...Cheers Steve

[@naviddostani152]

Correct 👏👏👍👍🙏🧿

[@MM0SDK]

Any petroleum based grease is bad for use on slide pins as it can react with and swell the rubber seals. Synthetic/lithium based grease is best as far as i know.

[@langanontshatsha9375]

It was going to be a great video but unfortunately I can’t see anything due to poor lighting, it was like I’m listening to radio

[@8ile]

Quite evidently on a dodgy MOT/NCT as it's called there.

[@folk.]

use copper paste in between before putting the disk back on.

[@Dazwillett]

First 👍

[@bodgitandleggitgarage]

Adam Willett LOL

[@opl500]

You don't want to grease the pad? :)

[@bodgitandleggitgarage]

opl500 lol

[@ewb69]

facial grunt lol

[@bodgitandleggitgarage]

ewb69 lol