Body Armor Hiline Bumper + XRC Winch, 24" Lightbar DIY Install onto 3rd Gen Toyota Tacoma | Mod #43

[@mikeschoolcraft21]

I got mine for $530 shipped from Morris 4x4 back in March. It looks great and works perfectly with the TRD skid plate and weighs less than 40 lbs.

[@modXELA]

Nice... but 40lbs just for the bumper correct? My total weight between the bumper, winch and lightbar is 165lbs which lowered my front end and now I have to do a lift... it never ends. lol... thanks for tuning in Mike!

[@tgtech570]

I think I like your method the best because other installation videos show them removing the entire front bumper but yours doesn’t. Great job!

[@modXELA]

Thanks Troy. I appreciate you for tuning in.

[@bloodstriper3649]

One of the best videos on this assembly I've seen. Thank you!

[@modXELA]

Hey Blood Striper, that means a lot to me, thank you. Just an FYI, after this install, theres tire rubbing due to the added weight so I need to install a levelling kit which will give it a 1.5" lift. I'll post the video by next weekend so tune in for that!

[@bloodstriper3649]

@@modXELA, thank you for this tip!!

[@Sheesh_masheen]

Great video! Very helpful especially seeing that you did it with out removing the factory bumper cover. Subscribed!

[@modXELA]

Hey Rybotron, I appreciate you subscribing and for tuning in! Hope to hear from you again soon!

[@stansbruv3169]

Subscribed! Excellent instructions. I can’t wait to get my Tacoma. 2 more weeks. 😢

[@modXELA]

2 more agonizing weeks… I know how that feels my friend! Congratulations on your new truck my friend and thanks for tuning in and subscribing stansbruv3169! See yah!

[@610moto5]

best install video out there for this front bumper. Thank you bro!!

[@modXELA]

I appreciate your comment 610moto5! Check out my other videos and stay tuned for more my friend, cheers!

[@kovaks1483]

I just got my white... And looking into how beautiful it can become.... Yours look damn beautiful brother!

[@modXELA]

Thanks Kovacs, I appreciate it bro! Check out my other videos, I've uploaded most of my mods in this channel... thanks for tuning in!

[@Fliptyper69]

Well done, your front bumper looks great. thanks for sharing the install 👍

[@modXELA]

Thanks for tuning in Mcdave!

[@teddymuscio7419]

Good job Alex. Looks great. I hope u have fun with your new toy.

[@modXELA]

Thanks Teddy! I'll be more confident offroading solo now so less stress = more fun! Thanks for tuning in!

[@muddyh2o2init44]

Good job! Covered all the points . Nice install…

[@modXELA]

Thanks Muddyh2o2! I appreciate you tuning in!

[@g7003041]

Awesome, if I'm your neighbor, surely I will join you on your offroading so that you don't have to go solo. Great job!

[@modXELA]

Hey g7003041, where do you live so I can move in. =) Thanks for tuning in!

[@g7003041]

@@modXELA I'm located in FL

[@modXELA]

@@g7003041 Oh nice... will probably move down there when I retire but that won't be anytime soon! =P Cheers!

[@props-model-shop]

Best instruction video I've seen so far. Well Done!

[@modXELA]

Hey Greg, that means a lot, thank you. I just recently posted a demo video ( kzbin.info/www/bejne/inPagWhto5V5hLs ) on how to operate this so check it out when you get a chance! Thanks for tuning in!

[@props-model-shop]

@@modXELA Hi, The 24" light bar can't be shipped to the USA. Do you have another recommendation?

[@modXELA]

@@props-model-shop There's quite a bit of selection on amazon.com. As long as the specs are similar to it (www.amazon.ca/gp/product/B0185FOTL2/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1), you should be ok. The Nighlight brand is nice, I would consider that not unless you want to spend more. =) Good luck!

[@JoKalpits]

Nice shortcut, thanks!

[@modXELA]

You’re welcome. Thanks for tuning in Jo!

[@blueagle3000]

WOW Alex she looks amazing from the front cant wait to see her from the back. lol :)

[@modXELA]

hahaha *wink*... thanks John!

[@billy-jadeachiu2296]

Looks fantabulous Mr Alex...😊

[@modXELA]

Thanks Billy-jade! One more offroading install/mod to go... I will have to do the enivitable 3-inch (at least) lift! Maybe next year. For now, time to really enjoy my truck! =)

[@tacomafan5186]

A great informative video. My only concern is the cooler line bracket that gets unbolted from the frame. In all the videos I’ve watched, there is no way to reattach it. Certainly Toyota put that bracket there for a reason. Have you had any problems with the cooler lines rubbing or chaffing?

[@modXELA]

Hey tacomafan! I will take a peek at that cooler line for you this weekend…

[@tacomafan5186]

@@modXELA I appreciate that. I had gotten my answer. I am told it is a power steering cooler.

[@Rollyman]

Great job Homie!! I was just looking on the DV8 for my Taco.

[@modXELA]

Thanks Rollee! My first option was to go with the DV8 as I like how easily it is to replace the lightbar due to the easy-access design and it's a little cheaper. However, it was not available at the time of ordering so I went with Body Armor. Not much of a difference though so you can't go wrong going either way!

[@Rollyman]

@@modXELA Thanks Kabayan. Hope to see you on the trail someday😊👍

[@modXELA]

@@Rollyman hopefully... I have a friend in San Diego who's been bugging me to hit the Rubicon trails... I don't know about that (yet) but when the time comes, we should hook up! Your bike rides look like a ton of fun btw! Keep at it pare ko!

[@geofish]

very well detailed install - really appreciate it! Best how to install i've seen for installing this bumper

[@modXELA]

I appreciate your comment very much. Thank you for tuning in GeoFISH!

[@christophermartinez5314]

Awesome installation

[@jonathansoriano9015]

Kuya. Your Pro is awesome. Inspiring my for Pro. Keep on posting

[@modXELA]

Thanks Jonathan! I think I have a couple more major mod to do which is a 3-inch lift and full under carriage skid plates. Not sure when I'll do these but tune in any time as I will be posting on a regular basis for sure. Thanks for tuning in!

[@ulisese.ericksonr.3401]

Amazing, love it, now I know, beautiful installation thanks 🙏👍

[@modXELA]

Thanks for tuning in Ulises!

[@PedroVethencourt]

Thank you for your video, I will be installing mine soon.

[@modXELA]

You're very welcome Pedro and thanks for tuning in!

[@GabinoGuevara]

Excellent job 👍, can add a video a connect the electric system to the battery o assign a new custom button to turn on the bar , I’m appreciate. Thanks 🙏

[@modXELA]

Sure thing but it's winter now so it will have to wait until it gets warmer! =)

[@frankz4900]

Excellent video sir

[@modXELA]

Thanks Frank Z, I hope it was useful to you and thanks for tuning in!

[@cajo791]

great job bro, can't wait to install my bumper guard too. ..Jo in Daly City

[@modXELA]

Hey thanks for tuning in Jo! Your truck lifted? Good luck with your install bro. Last time I was in Daly was 2018, my wife has relatives there. =)

[@jeremy8293]

Very nice video and well detailed! Also what set up do you have for you tires! Looks very nice

[@modXELA]

Hey thanks Jeremy... I'm running 285/70r17 Nitto Ridge Grappler Tires with RTX Baja Offroad 17"x9" Wheels (see install video here: kzbin.info/www/bejne/enSkcp6EZtaiapI) plus 1.25" wheel spacers (see video here: kzbin.info/www/bejne/qKO0iaV9r9OWr5o). I post videos of all my installations in this channel so make sure to check them out! =) Thanks for tuning in!

[@72soundguy]

Great install, looks awesome!

[@modXELA]

Thanks Jake, I appreciate it! Thanks for tuning in.

[@Mike-4547]

Thanks for the video. How much do you think the bumper weighs by itself?

[@modXELA]

Hey Mike... total weight of the whole assembly is 160 lbs. Winch with synthetic rope is 46 lbs, LED light bar is about 3-4 lbs, so 110lbs for the bumper guard with the D-shackles. I recently installed the TC-19339w Wings and that's an additional 32lbs.

[@Mike-4547]

@@modXELA thank you for the information.

[@modXELA]

@@Mike-4547 you’re welcome. If you are considering to install it, I would highly recommend that you install everything including the LED light bar the winch and the highline wing right off the bat. It’s a pain to do it piecemeal.

[@Mike-4547]

@@modXELA absolutely correct you did it was the best way everything in one shot.

[@dyates6380]

Excellent video!!!!!!!!

[@modXELA]

Thanks D Yates! Check out my channel for other mods/installs. 😀

[@tls5669]

once the cutting wheel came out I was done, guess im going with the blitz bumper

[@aspiringpro]

Blitz bumper requires cutting too and is $300 more

[@tls5669]

@@aspiringpro just a little part at the bottom, and you can go back to stock easily. Ill pay the extra 300 to be able to go back to stock and not have to hack the shit out of the front of my truck

[@aspiringpro]

@@tls5669 I mean why would I ever go back to stock? Besides, a new factory bumper costs only $200 + paint. the only risk is that of messing up during the cutting. You just have to be careful and use the right tool for the job.

[@brianrisdon8664]

Awesome job & Intel. Do you have to remove the factory recovery hook on the passenger side?

[@modXELA]

No, didn't' have to, it's still there. =)

[@BucksBe]

Great video! Just bought a white Tacoma and I've been eying this bumper so it's nice to get an idea of what it looks like. You did a great job. After a year, any issues or concerns? How has the winch fared?

[@modXELA]

Hey BucksQ, winch is good, I used it once this year so far and everything’s in good working order. No issues and I’m pretty happy with it! I will be installing the bumper wing later this summer so stay tuned. Thanks for tuning in brother!

[@dellann6861]

Great video Alex! I’ve been thinking of buying this particular bumper but can’t decide on what led light to get. There are so many choices available. How is the light bar that you’ve chosen so far? Did it come with the wire harness and switch? The Body Armor bumper do make the truck rugged. Galing ng video mo kabayan! Subcriber na rin ako sa channel mo👍

[@modXELA]

Holy crap pare ko... sorry I missed your comment, I just saw it now so pasensya na. Anyway, the lightbar is holding up so far, no issues with it. It did come with the wire harness and switch but I replaced the switch with an OEM style. Salamat for subscribing and thanks for tuning in. Hope to hear from you again kabayan!

[@davidstinson1458]

Can you tell me how far the body armor bumper sticks out from the front of your truck? Trying to see if it will still fit in my garage after the install? Thank you! Looks outstanding!!! 👍

[@modXELA]

Hi David, great question... it's just under 3" so call it 3"... I hope this helps and thanks for tuning in, see you again soon!

[@davidstinson1458]

Perfect. Thank you

[@dbottita]

Well done video, subscribed! Can you tell us if the additional weight up front is an issue? Did you have to change out your coil springs for heavier or was there really no effect overall?

[@modXELA]

Hey Dave, yes the added 165lbs on the front end caused tire rubbing so I had to install a levelling kit (Tuff Country 51025) which gave me 1.5"/1.5" lift... check the installation video here kzbin.info/www/bejne/oaumqpSrhJ2Gl9U and now, tire rubbing issue solved!

[@iamalemontree]

Great setup!! This will be my next project for my 🌮. How ya liking ur tires? Are they ko2?

[@modXELA]

Hey thanks iamalemontree! I have the Nitto Ridge Grapplers actually. It was a toss between that and the KO2s. I read a few reviews that the KO2s were a tiny bit noisier compared to the Grapplers so I took a gamble. So far, it's paid off and I'm very happy with it (not that the KO2s would have been a bad choice as you won't go wrong either way). It performs well on paved road and offroad. Crawls through rocks, sand, mud without issues. For daily driving, it's great. No issues on snow or slush or rain either. IMO, I thinks it's even a little quite compared to the factory Goodyear that came with the truck. Also, I prefer the look of it a lot more than the KO2s but again, either will be a good choice. I have the install video here if you wanna check it out: kzbin.info/www/bejne/enSkcp6EZtaiapI thanks for tuning in!

[@iamalemontree]

@@modXELA thanks so much Xela! I will be on the look out for those nitto ahh they do look bad azz!

[@aspiringpro]

You state that you are installing a 24" light bar? I thought the bumper only fits a 20".

[@modXELA]

Hi aspiringpro! That's correct. The lightbar as advertised says 24" but in reality, it's shorter than that. Best way to put it is that it's like buying 2"x4"x8' lumber, it's actually 1.5″x3.5″x8'. I hope this helps.

[@ealdydar]

Are there any no cut bumpers made for 3rd gen Tacoma? Ive been looking and everything requires cutting. This is my first Tacoma and with my past F150's , Colorado's, and Silverado's ive been able to replace the bumper with after market with many styles with no cutting.

[@modXELA]

What’s wrong with cutting? I think bolt-on-only type of bumper guards are only available for 2nd gen.

[@sniper9424]

Were you able to replace your front license plate, since you have the light bar and winch?

[@modXELA]

Hey sniper9424! I have the flip-type license plate holder but I decided not to install it at the moment. My front plate is on my windshield at the moment so let's see how long until I get harassed by cops about it... lol. *crossing fingers*

[@jamescorrigan4149]

Great job! Any concern with airbag sensor?

[@modXELA]

Hi James, airbags will still work and I hope that I will never find out (if you know what I mean). No wires or connections were present or taken out from the crashbar so I'm not concerned about it. My real concern though is the amount of damage that it will cause in the event that I hit something head on as the crashbar is made out of aluminum and very light and this bumper guard with the winch is 165lbs combined so it could cause some damage. However, this is functional and more of a necessity for me vs looks so I wanted to do it. Thanks for tuning in!

[@grayghost1423]

New subscriber here, good information.

[@modXELA]

Thanks for subscribing Bruce, it means a lot to me!

[@GoldenFriedTofu]

Looks AWESOME! where do you reattach the front license plate?

[@modXELA]

Great question Christopher. A mounting plate was actually provided with the bumper system. However, it gets installed where the fairlead is so that wasn't an option for me. I could get a plate mount that flips up when using the winch (which is actually a very good option) but I didn't like the look of it so until I get pulled over for not having it mounted on the bumper, it will sit on my windshield for now. If I have to install a holder, going with the flip version will be a challenge now as you'll have to remove many things to get at the installation points. I hope this helps, thanks for tuning in!

[@GoldenFriedTofu]

@@modXELA I just got my Tacoma a little over a week ago. I’ve been looking at these exact bumpers for a while. Like you, I live in a state that requires a front license plate. I like the winch idea. If/when I get this bumper, I may hold off on the winch so I could have a place to mount the front license plate. Thanks for putting together another great video! You made it look a lot easier then the other install videos I’ve watched.

[@modXELA]

​@@GoldenFriedTofu The two things that you can bypass to save time and effort is the bumper removal and applying of tape for the markings. These are not necessary at all. Also, take a look at the DV8 bumper as well if your looking at bumpers, it's pretty much the same as the Body Armor but at a lower price. Thanks for tuning in Christopher and congratulations on your new Taco!!! =) Enjoy.

[@danzig-vf6bx]

I really like this bumper but how do you get to the clutch on your winch

[@modXELA]

Hey Danzig-vf6bx, watch my demo video on how to use the winch here: kzbin.info/www/bejne/inPagWhto5V5hLssi=yvIoPPfSOewWvBMi

[@rmhignite]

Did you ever make a video on running the winch / accessing controls?

[@modXELA]

Hey rmhignite, yes I did but I just need to edit the video before I can post. I just got back literally just now from Jersey, Long Island, Pennsylvania and Delaware and I am beat from all the driving so I promise to post by this Sunday. Thanks for your patience!

[@danpauls3323]

This is the combination I am considering for my Tacoma - how hard is it to plug in the controller to the winch once it's all installed? Is the winch accessible by opening the hood, or do you have to come from underneath? Also, about how much did the front end drop with the added weight? Did you get the truck realigned after adding the weight? I still have my stock suspension (TRD Off Road) and don't run oversize tires.

[@modXELA]

Hey Dan, great questions! Plugging in the controller is not an issue which you have to access from the top by opening the hood. I'm only 5'7" and I can reach in from the front with no issues (at least until I lift my truck). Alternatively, if you can securely mount the controller somewhere in the front bay area, that would be good too so you won't have to be plugging/unplugging all the time. I'm choosing not to do this for now as I'm afraid of losing it. Before the winch/bumper install, I was able to get rid of tire rubbing (on 33's with CMC) but I am now experiencing some rubbing due to the 165lbs added weight causing a drop. I don't want to replace my Fox 2.5 coilovers yet so I am going with the Tuff Country 51025 kit (front strut spacer and rear AAL) which will give me 1.5" lift. This should take care of the rubbing. You'll be fine with your 265s!

[@danpauls3323]

@@modXELA You might be able to secure the remote using something like this: www.amazon.com/Quick-Fist-Clamp-mounting-equipment/dp/B006NOC8Q6/ref=sr_1_19?crid=DLGTZFDR1VHL&dchild=1&keywords=tool+clamps+for+truck&qid=1629726333&sprefix=tool+clamp%2Caps%2C224&sr=8-19

[@julestrdprodjimavicpro2869]

I have the same set up! good choice!

[@modXELA]

Since I installed this, it added 165 lbs to my front so I now need to lift my truck as my 33's are rubbing... again. =( Any how, thanks for tuning in!

[@julestrdprodjimavicpro2869]

@@modXELA I added a extra 1.5 in the front and back lift

[@modXELA]

@@julestrdprodjimavicpro2869 I'm doing the same thing. I ordered the 51025 Tuff Country levelling kit... just waiting for it to arrive.

[@julestrdprodjimavicpro2869]

@@modXELA I went with the Wescott Design TRD PRO lift kit and Icons Leafs

[@osamaabdelgader8348]

how's that winch holding up so far and do you honestly recommend ? Very great work by the way!! I have a super white as well and it'll look sick. Thanks

[@modXELA]

Hey Osama, good news is, I haven't had the chance to use it. I took 5 offroading trips this summer and went without a hitch so the winch kept pretty tucked up in there. Bad news is I can't give it any recommendations as I don't know how well it performs. From an installation perspective, it was easy, a definite DIY project. Aesthetically, installing the bumper and winch completed the overall look that I aimed for so at least I have that! =) I will make sure to make a review video as soon as I can. Thanks for tuning in!

[@osamaabdelgader8348]

@@modXELA Thats good !! At least you have not used it yet still in a good condition. Your rig def looks gorgeous thank you for the reply.

[@jkay1490]

Im thinking to buy 2022 Tacoma Trd pro

[@billdean.x]

Just ordered one

[@modXELA]

Nice!! It's a fun install, good luck with it William!

[@marielperez3064]

Hey brother, new subscriber here. A few questions. I will be installing a 4wp front and rear bumpers soon. 1) will the cut be the same with the BA.I do like that you did not remove the bumper out completely. 2) will my hidden caliraised lightbar behind the grill be on the way with the winch? Salamat bro.

[@modXELA]

hey Mariel. I'm currently away on a business trip but will be back home on Friday. I will have a look at my truck to address your Q's. Sorry for the delay but I'll get back to you soon. Salamat kaibigan!

[@modXELA]

Hey bro... 1) sorry but I can't say for sure if the cut will be the same but will be similar process for sure. 2) the front of the winch is 2.5" from the lower grill where your lightbar is. As long as it's not sticking out by that much, you should be able to clear it.

[@marielperez3064]

@@modXELA i does look like the cut on the BA is wider compared to the 4wp. Someone suggests to cut it where it flattens. Hope i can remove the crash-bar out with the bumper intact. Salamat kaibigan.

[@modXELA]

Good luck with your install, would love to see after-photos! I appreciate you tuning in... salamat pare ko! Btw, do you speak fluent tagalog?

[@marielperez3064]

The install went really well. It was a lot of work.. I love the 4wp front and rear bumpers. What is your measurements now with the added weight ? Yeah i soeak fluent tagalog. And bisaya.

[@ElStriker777]

🔥👍

[@weeweed86]

Nice job.....

[@laurencehiggins239]

How much sag did you have in the front end. I already have a lift with coil overs so I can adjust them after the fact. Just curious. Awesome video brother, my setup is going on in 2 weeks. Same as yours, just a Warn winch instead.

[@modXELA]

Hey Laurence it sagged a bit and enough to cause tire rubbing. Unfortunately I did not measure before and after so I couldn't tell you exactly how much it sagged. However, after installing the 51025 Tuff Country leveling kit which is a 1.5/1.5 lift (checkout my installation videos on that), rubbing disappeared so it would be safe to say that it sagged by 1.5" at the most. Nice choice you made there with the Warn... a little bit off my budget =) but my setup will suffice. Thanks for tuning in bro!

[@laurencehiggins239]

@@modXELA awesome brother. My icon lift will adjust, thanks for the info, I’ll send pictures once it’s all installed. Do you have an email address brother?

[@modXELA]

@@laurencehiggins239 hey, photos will be 👍 send to [e-mail]. BTW, how do you like your icons on the road and offroad? I'm considering the Beilstein 8112... eventually.

[@laurencehiggins239]

@@modXELA I have the icon stage 5 lift kit with the adjustable upper control arms, it’s amazing. Rides like butter on the road and is amazing off road. It’s not cheap at all, but it was money well spent.

[@modXELA]

@@laurencehiggins239 yeah I'm hearing nothing but good things about the icons. I'll definitely consider it when it's time for me to upgrade 😉

[@thumperbangin2000]

How do u feel it is for stremgnth ? Strong enough for winch pulls? Strong enough with how it mounts to the frame ? Thx

[@modXELA]

Hey thumperbangin2000, I've tested it winching an F-150 (see my demo video here: kzbin.info/www/bejne/inPagWhto5V5hLssi=q4CwWx_30EUsim53) and it handled it without issues. I also winched out my son's Honda Civic last winter off a ditch and it didn't even flinch so I'm very pleased with this installation.

[@thumperbangin2000]

@@modXELA good to hear. Ive been reading up on the front frame reinforcement plates. I think I'm over thinking things though.

[@modXELA]

@@thumperbangin2000 nothing wrong with overthinking things especially when it comes to safety. I'm sure engineers did their R&D due diligence before putting out a product (one would hope anyway)!

[@thumperbangin2000]

@@modXELA just a side note. I have the replica version of the hiline. Scored it for $260 shipped. I bedline painted it, its ready for install 11/1

[@modXELA]

@@thumperbangin2000 $260 is a big steal! Good luck with your install. I’m thinking of installing a hiline wing. What’s your opinion on that?

[@johnnyreb8030]

I'm going to buy this bumper and light and install it myself. What did you do for a light switch??

[@modXELA]

I just used the button switch that came with the lightbar and just stuck it where the rest of the light switches are as I've ran out of empty button spots. You can do an OEM style switch and here's of my videos showing the install: kzbin.info/www/bejne/b4CVaqlspaqoeMk Good luck with your install Johnny Reb! Would love to see how yours turn out!

[@davidr.1517]

Did you do a video on how ran the wiring into the cab for the lightbars off and on switch? Also, what switch did you use?

[@modXELA]

Hi David, I did not a detailed install video for the lightbar in this video and I just used the switch that came with it but I intend to swap that out with an OEM-style switch this coming spring. I have other videos that demonstrate switch installation for your reference (see kzbin.info/www/bejne/boqsZKWGa7xjpbM which is a video on how I wired the roof rack LED light bar). It's pretty straightforward, you just need to run the line for the switch through the firewall and connect the +/- leads to the battery and then the ground.

[@davidr.1517]

@@modXELA Thanks for your quick response. I know what you mean. It's getting too cold to be doing anything outside. Especially where you are at. Lol I just found you on Instagram too.

[@modXELA]

@@davidr.1517 here's a video on installing an OEM-style switch... kzbin.info/www/bejne/pISpgomBnrZ3eJI i hope this helps! I still have yet to post something on my Instagram lol... but it's coming. Thanks for tuning in David. Contact me at anytime if you have any questions.

[@davidr.1517]

@@modXELA Thanks and you too. I have a 2020 OFF-ROAD that I did the Bilstein 6112's and the 5160's . That front bumper and all are next

[@modXELA]

@@davidr.1517 nice lift system you got there. I want that same exact setup but I still want to keep my Fox 2.5 shocks so I went with the Tuff Country levelling kit for now.

[@tachoma8493]

Nice. 👍

[@modXELA]

Salamat! =D

[@Em2619]

Since the winch is hidden behind the bumper, how easy is it to access the winch controls?

[@modXELA]

Hey Josh, it's pretty simple and I actually posted a demo video ( kzbin.info/www/bejne/inPagWhto5V5hLs ) on how to operate this so check it out when you get a chance! Thanks for tuning in!

[@redbarron6574]

How much longer did the new bumper make the overall vehicle? I’d like to do this but my garage is tight.

[@modXELA]

About 2.5"... I hope it'll fit! One thing that I did not take into consideration was the amount of drop this 165 lb system to my suspension. Now I'll have to do a lift to rid off the rubbing. Anyway, I hope things work out for you and thanks for tuning in RedBarron!

[@chad7102]

How do you free spool or use wired remote?

[@modXELA]

Hey Chad.... check out my demo video here kzbin.info/www/bejne/inPagWhto5V5hLs

[@surfer04u]

I would love to know how you engage your winch ? Without a cut out in the front of the bumper to reach the winch

[@modXELA]

Hi Taco Tuesday. A few guys have asked the same thing so I will do a video to demonstrate. I'll send you the video link or just subscribe and turn on your notification bell so you'll know one the video is up. Thanks for tuning in !

[@Rungunseattacos]

Did you reinstall the bolt for the cooler lines? I can seem to get mine put back into place.

[@modXELA]

Yes I did re-use the factory bolts. Check the video at the 16:47 mark.

[@rmhignite]

What about the lone bolt behind the wheel liner that holds the line in place… did that one go back in?

[@silvestre08al]

It’s that a 24 inches light or a 22 in?

[@modXELA]

Hey silvestre08al... the description says 24" but physical dimension is actually 22". Just make sure that whatever you get, it measures out to at least 22" so you won't have a gap on the sides.

[@tgtech570]

What I want to know is how you can get to the winch in order to plug in the controller to operate it?

[@modXELA]

It's pretty simple, watch my demo video of it here. kzbin.info/www/bejne/inPagWhto5V5hLs

[@tgtech570]

@@modXELA very good. Thanks

[@p-51mustang51]

How did you angle the light bar correctly so that it is not pointing too far down or up?

[@modXELA]

Hey P-51 Mustang, for this specific lightbar, there's no option to change beam trajectory so I just made sure it was mounted flush against the anchor points.

[@tgtech570]

Hi Line bumper calls for a 20” light bar but you used a 24”?

[@modXELA]

Hey Troy. It's like buying lumber, the size is actually shorter than advertised. Mine is actually just under 21" and it worked out perfectly as the cutout for the light is 20.5".

[@travblurr8043]

Does anyone make a bumper similar to the Body Armor that doesn't require you to cut the OEM bumper?

[@modXELA]

Hi travblurr8043, I'm sure you did plenty of searching but I don't think it exists. I wanted to avoid all the cutting as well but I couldn't find one that looks similar to the BA or DV8 etc. However, if you Google "Toyota bumper guard" you'll see some that don't require cutting but they don't look anywhere close to this look. Good luck with your search and thanks for tuning into my channel!

[@davidr.1517]

Where did you buy the edge trim, or did it come with the bumper?

[@modXELA]

Hey David, it came with it 😀

[@robertmcivor834]

How do you engage and disengage the winch

[@modXELA]

Hi Robert, plug in the controller and there's a clutch that you toggle on/off. Here's my demo video of it: kzbin.info/www/bejne/inPagWhto5V5hLs Thanks for tuning in!

[@robertmcivor834]

Thank you that's exactly what I wanted to see. Getting ready to install the same setup on my 2021 OR. By the way love your videos

[@modXELA]

@@robertmcivor834 You are very welcome, good luck with your install and thanks for tuning in... I have done quite a few mods on my truck so make sure to check them out. This weekend, I will be installing bed and tailgate LED lights so stay tuned for those! Cheers!

[@ThePolarBearSquad]

How is your light bar any problems ?

[@modXELA]

Hey ThePolarBearSquad... no problems at all, works just fine. =)

[@ThePolarBearSquad]

@@modXELA thanks man

[@modXELA]

@@ThePolarBearSquad I appreciate it, thanks for tuning in!

[@Musaf3r]

what are your thoughts about the light bar that you are using?

[@modXELA]

Hey Musafir, it's pretty decent considering I only paid about CDN$50 for it. It gives out plenty of lighting and it's come very handy when I arrive at a campsite late at night. I really did not need another LED lightbar but since there was a spot for it in the bumper guard, I went this as it had decent reviews and wasn't a bank breaker.

[@Musaf3r]

@@modXELA Great, thanks.

[@chucksavage1980]

Where did you get the red TRD grill template ?

[@modXELA]

Hey Chuck. I got it from Aliexpress.com. Here's a link to it: www.aliexpress.com/item/4001009993186.html?spm=a2g0o.productlist.0.0.49d52ac0YrPK2p&algo_pvid=e5da30f4-7c4f-4aa3-bc34-9e890a4cf174&algo_exp_id=e5da30f4-7c4f-4aa3-bc34-9e890a4cf174-37&pdp_ext_f=%7B%22sku_id%22%3A%2210000013436736102%22%7D I hope this helps!

[@rubycalpito8043]

How heavy is the bumper and winch?

[@modXELA]

165 lbs combined

[@pdereniwski]

How long did the install take you?

[@modXELA]

Hi Pat, about 5 hours.

[@pdereniwski]

@@modXELA thank you!!!

[@anthonynguyen6009]

So you installed this on the stock suspension correct?

[@modXELA]

Hey Anthony, that's correct, on stock TRD Pro suspension but the weight caused the front end to drop so it caused tire rubbing that's why I ended up installing the 51025 Tuff Country leveling kit (1.5/1.5) which eventually solved that problem.

[@anthonynguyen6009]

@@modXELA I wanted to add the bumper with the light bar (no winch yet) on stock tires and suspension was curious on how much it would sag without the winch👀

[@modXELA]

@@anthonynguyen6009 unfortunately I couldn't say for sure but the bumper guard with the lightbar weighs about 78lbs so my educated guess would be about 5/8" to 3/4" drop. Here's an idea... try placing an object by the bumper that's about 80lbs and measure your height before and after and it should give you a rough idea on the drop. Also, note that if you're not planning to install a winch yet, it would be difficult to do it after the fact. You may need to remove the entire bumper guard in order to mount the winch on... just something to consider.

[@calebpflugrath9146]

Was there any gaps between the trim guard and the bumper?

[@modXELA]

Hey Caleb Pflugrath... there's a very slight gap in some points but almost negligible. Also, even if there is, I'm just curious to know why does it matter? Give me a few minutes, I'll take a close-up video for you and send you the link.

[@calebpflugrath9146]

@@modXELA ok. I was just curious because Im install the same thing and I want mine to be tight and not gapping. I’m pretty ocd when it comes to these things😂 I look forward to receiving the video👍

[@modXELA]

@@calebpflugrath9146 I don't think you can avoid some minor gaps and that's what the trim does, to cover up that gap. There's always an "acceptable" play in many installs. At any rate, here's the link to the video and I hope it answers your concerns... kzbin.info/www/bejne/ZnWui6Bumq2Lm6c

[@Ethereal_Nymph]

Good job brother, I need help

[@modXELA]

Hey thanks for tuning in Powell. Let me know if there's anything I can do to help. =)

[@dans2788]

How much if any does that bumper change the approach angle?

[@modXELA]

Not sure but it definitely dropped my front-end due to the 165 lbs added weight. This forced me to install a 1.5/1.5 kevelling kit to rid of tire rubbing.

[@shoegum7362]

How do you reach your clutch controls?

[@modXELA]

Hey Shoegum, since others asked me this same question, I will create a demo video and I'll send you the link. Will work on it this weekend. =)

[@chrisfernandez4631]

can you use a 22" led light bar?

[@modXELA]

Yes but you will have a gap at both ends.

[@PHILLIPS8822]

Doesn't this add weight to the Tacoma effecting gas mileage?

[@modXELA]

Hi Darryl, yes it adds 160lbs which equates to one person.

[@PHILLIPS8822]

@@modXELA Wow didn't realize it added that much weight

[@modXELA]

@@PHILLIPS8822 Yep, that's between the bumper guard, winch and lightbar. I had to install a levelling kit after as my front end dropped and caused tire rubbing in the wheel-well. =)

[@Pilsungbo]

It says on the website it fits a 20 inch light bar. Is yours truly a 24 inch? How does it fit?

[@modXELA]

There's plenty of room in there, you can adjust the light bracket accordingly. Although the description of the one I installed was 24", the physical dimension around 22" and it turned out to be a perfect fit.

[@Pilsungbo]

@@modXELA I ordered a 20. Should I order 22?? I don't want empty space when looking at it when it's installed

[@modXELA]

@@Pilsungbo the 20 will be short for sure!

[@Pilsungbo]

So 24 is the best size to make it full? No space on left and right! Why would body armor say fits 20 inch light bar. Shouldn't they say 24!? Lol

[@modXELA]

@@Pilsungbo I measured the hole for you just now and it is physically 20.625". The ends of my lightbar are literally sitting right at the ends. Just make sure that what you're buying physically measures more than 20.625 so you won't have a gap. My (so called) 24" physically measures 20-7/8". Same thing when you buy a 2"×4" lumber, it's never really 2"×4".... =)

[@silascastellanos]

Where do you live. Maybe you can install mine.

[@modXELA]

I'm in Canada ny friend so as long as you're in the GTA area, we can work something out. =)

[@silascastellanos]

I live in virginia. We are far away.

[@modXELA]

@@silascastellanos yep... that's quite a drive! Good luck with your install Silas!

[@indianpana]

Where in Canada olive in Vancouver

[@kermitec]

can you still reach the clutch on the winch?

[@modXELA]

Yes, I'm only 5'7" and no trouble reaching it. This is after lifting my truck by 1.5" as I got tire rubbing after the bumper guard and winch install.

[@kermitec]

@@modXELA I guess my question should have been, how do you get to the clutch on the winch? It looks like the winch is completely enclosed in the bumper, o how do you get to the clutch or hard connect your winch controller if the battery was dead?

[@modXELA]

@@kermitec The clutch does not need to be connected as it is sitting on top of the entire unit so it's very accessible. Maybe you're referring to the remote/controller - but this is also accessible. I can create a short video of this and I'll provide you a link by this weekend. Also on your note regarding the battery if it goes dead, connecting it would be moot point as I can't operate it without battery.

[@kermitec]

@@modXELA If you have time that would be awesome and if not then that's fine as well. Thanks a ton!

[@HM-vu9zw]

Did you remove the factory tow hook?

[@modXELA]

Hey H M, no, still there. Also, it's 20mm from the edge of the groove.

[@HM-vu9zw]

Thanks! It was a great help having this video as a reference while Installing my bumper, winch and light bar .

[@modXELA]

@@HM-vu9zw I'm glad this was helpful... cheers!

[@HM-vu9zw]

How have the bumper/winch/light bar held up? Any issues?

[@modXELA]

@@HM-vu9zw everything's holding up pretty well but my winch haven't seen real action yet (which i guess is a good thing) but i unspool and spool it once in a while just to make sure it's still working and to avoid seizing.

[@rogerjackson7144]

Do you have a volume control on that camara? If you do can you turn it up. Makes no sense watching your video if I can't hear you. Speak up man!!!

[@modXELA]

Sorry about that Roger. I will invest in better video recording equipment eventually but I don't have the budget for that right now. would be happy to answer any questions that you may have though. Cheers.

[@ThePolarBearSquad]

I can hear you good. maybe it’s that other guys speakers

[@finditfixitmechanics]

Yikes, thats over $700 American just for the center bumper. Better and cheaper options like DV8 for 100’s less. Good informative video though, thanks for making.

[@modXELA]

Yep... I did consider the DV8 but at the time of ordering, they could not guarantee delivery date due to COVID. The Body Armour delivery still took 2 months but oh well... anyhow, thanks for tuning in D Lash!

[@gabrielreyes8476]

You shoulda got the HF Badlands Apex 12000. It's better than a Warn or a Smitty and it won't leave stranded. Nice build none the less.

[@modXELA]

Hey Gabriel, nice, it looks like it has better specs. I wish I knew about it before my install. Anyway, I'm still happy with this and I'm sure it will do the job. Thanks for sharing!

[@baldhairyandfatguy]

Great video. Did your bumper come with the black trim to cover the cut? If not could you please link to it? Thanks.

[@modXELA]

Hey baldhairyandfatguy... it came with it.

[@baldhairyandfatguy]

How did you mount the front license plate bracket that comes with the bumper? It's required by law where I am.

[@modXELA]

Hey baldhairyandfatguy, I didn't use the one that came with it. There's one you can buy that flips up. I have it but I have not installed it yet.