How to Enable Remote Start RAM | Dodge | Jeep | AlfaOBD

[@Dan-p1f9d]

FYI, When some parameters are changed they need a specific amount of key cycles before they work. That's why it worked after driving it...

[@tinpea]

Brilliant! TY! This worked on a 2015 Jeep Grand Cherokee Altitude (original FOB) without having to reset ecu or test drive. For clarity, someone messed with my settings during a repair and left me without the remote start functioning.

[@martyposinski6392]

Thanks John for another helpful video in our Dodge & Ram community. You’re really doing a great job, keep up the good work because I get to live a part of my life vicariously through you with the things you are doing that I wish I could do. Lol

[@GeorgeJetson-o7p]

Worked perfectly on my 2013 Dodge Journey Crew. Programmed it first with your other video and was going to do all this reset and when I went out after 15 minutes and tried the remote start it worked. Yeah 🎉🎉 Did not have to do the reset, but want to thank you for making these great videos .... Cheers

[@justhere9937]

Did you have to add a remote Starr to your vehicle or just programed the computer?

[@szaw4452]

Thanks for the video... I had to do the RF reset/replace step. Work perfectly first try after that. No luck with the driving etc prior. Cheers

[@kostachristofides291]

Spot on worked exactly as you described on my second Jeep GC 2014 Overland, already had it from factory on my 2015 your a champion keep up the great work!! Both the videos are required normal key programming first then remote start also Read Pin from alfaobd was incorrect but calling a dealer gave me the correct code, wrapped love remote start !!

[@ronaldmoparornocar9590]

I believe you have to cycle the push to start through the rebooted RF HUB so it can do the cycle of lock doors flash lights and sound horn...heard that from a tech for dodge he had to install a new RF HUB and BCM in a RAM and I guess it was in the tsb. Was a recall to reflash the BCM.they did it and then it would not communicate with the RF HUB put in a new hub and got it to communicate and did what you did said road test cycle and it has worked since...but the service bulletin stated to road test cycle... hope it helps you and others ✌️👍👌🇺🇸🇺🇲

[@sr8shoota]

It's a bit different on older vechicles. On my 2008 dodge charger. My remote start went out and the inhibit reason was no hood switch. So I looked din alfaobd amd remote start was on but I could not find hood switch. It is under output b14 I th9nk. Make sure you turn that on.

[@skipg23]

Are all Ram trucks wired for this? I have a 2014 Tradesman or do I have to install a remote start

[@beardedg1nge303]

did you ever figure this out?

[@Repny2dafullest813]

Nice I almost paid the $200 for the other plug n play methods. I'ma try this out first and solder the button on the key fob.(2019 classic)

[@dearinghoward]

So you don’t have to have the module or antenna behind the back seat?

[@Blubyu99]

Will that key fob work on a Canadian Ram 1500 SLT truck?

[@McChuckD]

Another great video! I haven’t started changing anything yet but when I do, I know where to get the info! 🤘🏼🔧⚙️💯

[@BoostedMotorsports]

💪

[@serchbey]

Thanks for your video, it worked awesome with my 2014 Cherokee KL 2.0 Multijet Europe, just program the new fob in RFH, then enable the Remote start in the BCM, finally do a PROXI and done.

[@serchbey]

@@antijacobik Hi, you have to put the ingnition´s switch in the "OFF" pos, then in ALFAOBD go to "RFH" (Radio frecuency hub) -> "ACTIVE DIAGNOSTIC" -> "Read PIN" -> "START"(copy the 5 dig pin code ) -> "Program Ignition FOBIKs Highline System" -> "Enter PIN Data (5 digits)" -> "START", You have to push the unlock button once when the proccess ask to do so, wait some seconds and you´re done with the Fobik´s programming To enable Remote start: Put Ingnition´s Switch in "RUN" -> "BODY COMPUTER" -> "Body computer Delphi/Marelli" -> "ACTIVE DIAGNOSTIC" -> "Car configuration change" -> " Remote Start" -> "Select Value" -> "Present" -> "Start" wait a litle, then: "BODY COMPUTER" -> "Body computer Delphi/Marelli" -> "ACTIVE DIAGNOSTIC" -> "Car configuration change" -> "PROXY alignment" -> "Start" fallow the instructions at the end of the proccess. Pay attention to the "PROXY alignment" proccess, so all the modules are succesfull in PROXY, anyway i recommend you to do the proxy twice. If you have as my car all the modules, for examples the "Hood Ajar Switch" enabled and in function so you don´t need to do any things more to get the Remote Start to work, in my case it worked so. Enjoy it!

[@oleh.pavlyk]

Hi. I am also interested in how you did it. I have the same car. Could you share the instructions? Unfortunately, I lost one key.

[@serchbey]

@@oleh.pavlyk Hi, you have to put the ingnition´s switch in the "OFF" pos, then in ALFAOBD go to "RFH" (Radio frecuency hub) -> "ACTIVE DIAGNOSTIC" -> "Read PIN" -> "START"(copy the 5 dig pin code ) -> "Program Ignition FOBIKs Highline System" -> "Enter PIN Data (5 digits)" -> "START", You have to push the unlock button once when the proccess ask to do so, wait some seconds and you´re done with the Fobik´s programming To enable Remote start: Put Ingnition´s Switch in "RUN" -> "BODY COMPUTER" -> "Body computer Delphi/Marelli" -> "ACTIVE DIAGNOSTIC" -> "Car configuration change" -> " Remote Start" -> "Select Value" -> "Present" -> "Start" wait a litle, then: "BODY COMPUTER" -> "Body computer Delphi/Marelli" -> "ACTIVE DIAGNOSTIC" -> "Car configuration change" -> "PROXY alignment" -> "Start" fallow the instructions at the end of the proccess. Pay attention to the "PROXY alignment" proccess, so all the modules are succesfull in PROXY, anyway i recommend you to do the proxy twice. If you have as my car all the modules, for examples the "Hood Ajar Switch" enabled and in function so you don´t need to do any things more to get the Remote Start to work, in my case it worked so. Enjoy it! Svara

[@james-browny]

I am trying to install a Mobokey remote starter in Dodge RAM 2013. I have done the remote unlock part. They dont have an OBD device. It has its own wiring and stuff.

[@135ieric5]

Im wondering if I can do this to my 2012 4 gen 2500

[@Relevantminded]

You can buy the hood pin separately, plug it in, and mount it along the hood rail it'll work, too.

[@jtoland80]

Thank you for this info, I want to get my tradesmen to work too

[@alejandroernestomeyeraltamiran]

I have a Dodge Durango 2005, and my original key fob has only the open, close and panic button; i bought a key fob with remote start, but it does nothing, only the original buttons work, when i press the remote start button only makes noise inside but it does nothing; my question is: can i do this same thing to my Durango?

[@kreazyd]

I just added a rear view camera on my 2014 Ram1500. It has the 5 inch screen and didn’t have a reverse tailgate camera but when I installed the new tailgate handle with a Mopar camera I found the wires for a camera were there. I just plugged the camera in the socket. Can I use the AlphaOBD to program the screen to work with the new camera?

[@CarsTrucksWhatever]

That's awesome but my came with remote start but I have to get a new key fab because I lost a set keys somewhere at work lol this is good to know

[@azmaz73]

So am I understanding this right, ANY model can be programmed to remote start with a new fob? Even my pretty basic 14 express?

[@WhiteNoiz]

Taking it for a drive might be like programming a tach on an aftermarket remote start. You can't make a remote starter work until it learns the tach feature. That would be my guess. Could try just turning the truck on for a few minutes and shutting off.

[@jonnycola5398]

Do you need to have the remote start button on the fob to work or can you just hit the lock button three times

[@johnnyninetytwo]

That’s for start x

[@Ukeelau]

My 2014 Laramie has the FOB with the air suspension button. Does that feature have to be programmed as well?

[@gleem1751]

I have a 2014 big horn. Tried to put a 2018 8.4 uconnect in it. Got everything to work except backup camera and steering wheel controls. Any help?

[@joshjohnson5347]

So your saying you can just toss a resister in there, and activate it with jscan?

[@lovemyguns1000]

Will this alter any engine tunes already installed?

[@TheBullboy1]

Love ur video great work

[@hotballer02]

I have a question I have a ta with the regular seats with just heat and upgrade to the full alcatera seats with heat and cool will this let me add the cool seats in the bcm so it will show up on the uconnect

[@OT_Tips]

I have a 2010 with a key fob you insert. I’ve seen some aftermarket remote start dongles that use the Lock button as the way to remote start the truck. Would the key fob you bought fit since I’m using the Lock button instead of the button you’re using?

[@o2c4u]

Does this work for 2023 ram 1500 bighorn?

[@MM_in_Havasu]

Very cool tutorial! Thanks John for great video content!

[@BoostedMotorsports]

Thanks mark!

[@TheRealThaenatos]

So I'm seriously considering doing this, but worried my 2016 express might be missing something to make it work. Do you by chance know that this would work on a lower end ram 1500?

[@TheRealThaenatos]

Did this right after posting. Only needed to ground pin 11 on the upper left BCM module. I wouldn't recommend purely for the hood safety mechanic not working. But it works great!

[@Gatorman6924]

@@TheRealThaenatosis this the one by the brake pedal?

[@TheRealThaenatos]

@Gatorman6924 the BCM is near the brake pedal.

[@Gatorman6924]

@@TheRealThaenatos did you have to use the resistor? Or just straight ground?

[@TheRealThaenatos]

@@Gatorman6924 straight to ground

[@ShoriOmar]

Hey, i get failed. the ecu has detected that the request contains parameters with value outside allowable range. When trying to RF-HUB reset/replace. What is the cause of this?

[@jonny_chain1970]

Does it work with Ram 2500?

[@yzfmatt7107]

Will those two videos work on a 2019

[@maverick__mike]

What about for those with push button start?

[@Octiviono]

Boosted performance and features!! Nice Vid!

[@BoostedMotorsports]

Yes sir! It’s the little things 💪

[@Hugolopez732]

Where would I be able to buy a resistor for this?

[@Unfinished-Business24]

If I have factory remote start would I have to program the remote start separately on my fob or since I had it stock does it just pick it up or I need to do 2 programs tia brother

[@V6Chargerguy]

We're did you get your after Market key from

[@hhporsche83]

I have a dodge Durango SXT 2015, the first issue I got is the invalid PIN, the Alfaobd shows me a pin but it seems invalid, so I went to a locksmith and he gave me the correct PIN and he programmed it for me. I enabled the Remote start from Alfaobd, but my car doesn't have a sensor for Hood, so I kept PIN 11 settings as No, which didn't work for me, then I tried to make the PIN 11 value as Yes, but now it shows me an error when I try to Remotely start the car "remote start canceled hood open"

[@scottcpan68]

I can tell you that to add the OEM remote start on the Dodge Durango, you will need other parts besides just programming. I have a 2014 SXT and I bought the Mopar remote start kit # 82214118, which I believe only works for model year 2014. There is a revised kit with a different part # 82214597 for 2015. The kit came with the hood latch, wiring harness, a new RF Hub with a different part # and an additional antenna module to be added in a spot where there was none from the factory.

[@pido0082]

hi you think i can do that on my2013??

[@jamielawson1534]

Great video but I installed one on my 2018 Ram 1500, all went well, used alfaobd to add all the settings and program the keys. The issue is when I push the button on the remote the horn beeps but no start, get a message on the EVIC that says REMOTE START CANCELED HOOD OPEN. The hood isn't open. I did the take it for a drive thing but still doesn't work. Any idea's?

[@ryanseigfried2496]

Check to see if you have the correct hood latch with wiring... if not... the wire may not be in the plug in the body controller... the bcm is way up under the dash on the left... on the driver's side

[@jamielawson1534]

@ryanseigfried2496 thanks, I ordered the kit from the Mopar dealer. The instructions say if the existing harness has the plug for remote start to NOT use it, as it would cause failure. I've got the new wire run, but will have to get someone to add it to bcm, just too tight for me to reach it.

[@hidros1461]

What size resistor?

[@Zaid-pi2qq]

what about GM car how to enable remote start ??

[@autotronics918tulsa5]

What is the resistance value on the hood latch?? Bro?

[@autotronics918tulsa5]

IM THAT GUY THATS GONNA PUT THAT RESISTANCE 🤣🤣🤣🤣🤣

[@420him420]

A 1000ohm 5watt 1amp resistor should doo it

[@autoguydiy4244]

You have to drive it so the truck can register the change. Same process if you disconnect the battery before you get it inspected You have to drive the truck 40 to 60 miles to let the computer do its run sequence and pcm can accept your changes

[@BoostedMotorsports]

That’s a different scenario. Disconnecting the battery and having to drive it before an inspection is so that the emission monitors can run and pass the checks. I’ve done a ton of computer changes and usually they are immediate or within minutes. Even the key fob was instant. The remote start requiring a drive is a weird odd ball one

[@autoguydiy4244]

@@BoostedMotorsports That's what's up. I will stick to my guns big dog. These newer computer systems are weird. I think the same principle applies

[@nl0hal]

@@BoostedMotorsports probably a security feature, if you change functions to open/start the vehicle remotely, a unwanted copy of the FOB by a bad guy can't be used right away to steal the car. It need a full "key-cycle" to activate the change. Key-cycle maybe defined by distance or time running... {maybe only in Pushstart versions IDK).

[@estebancarrera6375]

Off topic but involves alfaobd hopefully, I have a 2014 ram 1500 limited, the gains on my cluster won't go up or down and it says "trailer not connected", brakes and turn signals work, (I've tried attaching to multiple trailers) is there anyone that could help out?

[@brothertrucker3304]

I have the same problem with my 14 i cant figure out how to fix it either, i did disconnect the trailer brake module under the drivers side foot well and the message went away

[@brothertrucker3304]

But plugged it back in and it came back

[@estebancarrera6375]

@Brother Trucker I got the problem fixed. My truck came with air ride suspension (changed it to coil over), and I unplugged some fuses to get rid of the service message. Turns out that for some reason, the trailer brake controller and the air suspension share a fuse.

[@brothertrucker3304]

@@estebancarrera6375 thanks for letting me know ill check through my fuses and see if ones bad, mine doesnt have the air ride but its worth a shot to check

[@gerr35]

We're do you get the resistors

[@BoostedIntegra]

Has anyone done this with a tradesmen? Mine came with a physical key (no remote unlock) but I was able to program a key fob and the remote unlock. I’m hoping that means I have the rf hub and other hardware to program remote start

[@walcont]

How did u do it ? Because i have tradesman 1500 2017 , i took it to locksmith he programmed a fob to start the car only he couldn’t make the unlock/lock buttons to work , I tried to do it with alga obd same thing only start the truck key functions lock/unlock does not work .

[@BoostedIntegra]

@@walcont Do you have power lock/unlock inside the truck? If so you can program it with alphaobd.

[@BoostedIntegra]

@@walcont Checkout the video I uploaded on my channel, I go over how to program the remote unlock.

[@jdfjbird76]

Bro what I need is to know what size ohm resistor to purchase??? Asking for a friend:)

[@420him420]

1000ohm 5Watt 1Amp resistor, search up how to bypass the hood latch sensor for confirmation

[@leoscott321]

How do I disable my remote start on my 17 Ram 1500? My key can be in my pocket and it still starts my truck randomly. I push the lock button to go somewhere and it’ll just start another one or two more times before I even make it inside.

[@gleem1751]

2:30 Change your present to NO 2:55

[@MrMando9909]

To fix it, open your key fob and super glue the silver contact on to the button

[@yzfmatt7107]

Or would I have to add a bypass to get into the computer

[@DanielGarcia-zi3wx]

I am working on my 2014 RAM. Following all the instructions in the video, I was able to code the new key with remote start button, but when I want to remote start using the new remote, it just honks once but won't start. On the dash it says "press the brake and press the start button"

[@DanielGarcia-zi3wx]

I checked and mine does not have the hood sensor wiring

[@brycerushing]

i’m having the same issue any luck?

[@thedodgenutt]

Best place to purchase alpha obd ?

[@mysticjuzo6783]

Play store android only or on pc (windows)

[@pido0082]

i have a remote start canceled hood open

[@aaronr1926]

Any idea if I can do this on my 2016 dodge dart se

[@BoostedMotorsports]

Should be similar. Some models required an antenna for remote start but the rest should be the same 👍

[@aaronr1926]

Perfect thank you very much

[@derekprice5510]

On a 2014 Ram is the remote start already installed but just needs to be activated with AlfaODB?

[@kentwicker6818]

I don't think so. I'm working on a 15 now. The factory kit I bought has a new RF module and antenna module so the 14 is probably similar.

[@brothertrucker3304]

I have a 2014 too Im working on this right now i programmed a new key with the start button, i turned on all the settings like in the video but when i try to start it with the key the dash says "remote start inactive hood ajar". So my guess is i need the resistor, because the truck honks like its going to start but it doesnt. I can let you know if it works this weekend.

[@kentwicker6818]

@@brothertrucker3304 The switch probably isn't that expensive. What if you are working under the hood and someone accidentally starts it?

[@brothertrucker3304]

@@kentwicker6818 if someone plans on going the route of not getting the latch and plans on working under the hood hopefully they know that is a possibilty And disconnect the battery or put the key in a safe place so that cant happen. Im just testing to see if it works. And if i can find a latch for a decent price ill probably snag it which most people probably should.

[@DanielGarcia-zi3wx]

@@brothertrucker3304 I am working on my 2014 RAM. Following all the instructions in the video, I was able to code the new key with remote start button, but when I want to remote start using the new remote, it just honks once but won't start. On the dash it says "press the brake and press the start button"

[@thewhitedemon0761]

I got one thing I want to say get a 2500 Cummins

[@manny.5.7]

If I have a tune will this erase the tune?

[@BoostedMotorsports]

No

[@Gatorman6924]

Can you do this with jscan?

[@Gatorman6924]

I am pretty sure you can, I did alot of the thing you can with this… But ended up just getting the other for the support.. No real video or much support for Jscan, but it is all there from what I have seen

[@BoostedIntegra]

@boostedmotorsports What resistor should be used to do this?

[@phillipburrows2479]

I read that it’s a 1k ohm

[@frankl9254]

Does alpha obd work on 2011 ram?

[@JamesValentineBaja1000]

Ya

[@robgill4378]

Hey bro what size resistor did you use in that hood latch plug?

[@420him420]

I figured it out its a 1000ohm 5w 1amp resistor 🤘search up how to bypass the hood latch sensor and you can get confirmation

[@lakelandcarkeys]

your original key does have the remote start button, it just does not have the pop pad inside the key to press the button. if you put that pop pad inside your original key, the button would work.

[@tgtshirts1]

Thumbs UP.!

[@christophermellon1980]

Doesn't work on 2019... It won't read any pin... It just says it's not able... They told me after 2018 you can not just get a pin.

[@christophermellon1980]

Don't get me wrong... It's a great program, I love it. Used it alot actually. ☺

[@mikescott6247]

I got 2019 classic it still be the same?

[@Avanote]

Hey guys I know this is frustrating and hopefully I am not too late for some of you. It took me some atime but I think I got this. Follow this video but when you get into the WRITE THE SUSPENSION HEIGHT VALUES let the app read your truck sensors, then let your truck adjust its height and then STEP OUT FROM THE TRUCK AND MESAURE THE DISTANCE FROM THE MIDDLE OF THE WHEEL TO THE EDGE OF THE FENDER AND WRITE THIS VALUE FOR EACH SUSPENSION. After this your truck will adjust to its original height values, meaning this will adjust the normal, exit, off road 1 and off road 2 standard heights of your ECU System. Hope this works for you. kzbin.info/www/bejne/o6W5fZ5tjLVlrbc

[@pido0082]

can someone helo me

[@TheMarcial53]

“IF” someone wanted to get a resistor where could they get one that works for this application? 😂

[@jdfjbird76]

Asking for a friend what resistor and where to get it?

[@jdfjbird76]

Why can't we get answered?

[@420him420]

1000ohm 5watt 1amp resistor, shouldnt be to hard to find

[@cswatson4823]

I don’t think this works with an iPad???

[@JamesValentineBaja1000]

Absolutely not

[@bawarska_machina_wedrowna6713]

Get closer to the mask, what is the given resistor?

[@MrSwift05]

OBDLinkMX+$200.00 plus AlfaOBD Google play $60.00 Fobs $200.00 Total $460.00 NZD and none of them work GREAT !!!

[@420him420]

it all works just fine, did you install the obd port security gateway bypass? its needed in 2017 plus models...the dealerships put this on in order to stop people from using 3rd party diagnostic software and scanning tools making the consumer have to go to the dealership or buy really expensive scanners

[@Quiverfull12]

So you don’t have to have the module or antenna behind the back seat?

[@braden6402]

Nope