BoreMeister - Vibration-Free Solution for Deep-Hole Boring

[@lieberthj18]

I have the same tool from sandvik it's great - really no vibrations👌

[@amanlikhitker3118]

Do you have a such a tool which can done 1 meter length and 41 id

[@ДаниилСергиевский]

Haas have m38 command. Reduce slightly cutting depth and rise feed.

[@yuttapongtohtable]

please advise about standard to boring pup piece if reduce thickness from SCH80 to SCH40 and mechanical properties still contain.

[@naveenvandal4049]

Tool quality super, we need direct contact no tool and insert suppliers

[@gauthamkinim6564]

You should try Taegutec products. They also have a production unit here in India. More superior to tungalloy. Also both these companies work under one group IMC. So not a major difference in performance but prices are comparatively less

[@debjitkanrar7895]

Is that cylindrical thing in viscus fluid inside ....or how it works as damper ??

[@TungaloyCorporation]

Thank you for your interest in our tools. If you get the chance please check for this. www.tungaloy.com/us/product/boremeister/

[@hebbarlekhmissi9630]

Vous avez de la chance de travailler avec ces outils comme celui-ci à alleser utra moderne avec pastille en carbure métallique ,dans notre temps les outils c'est nous qui les confectionnons avec des barreaux d'acier spécial

[@kyoadam1593]

What about deep boring is there any

[@userwl2850]

I've never had luck with this type of tool. I use wood to support long tubes.

[@JesusSanchez-xu2is]

Are you using at least a split bushing? I've used these and they work great...

[@terrynaude284]

Jesus Sanchez what is a split bushing?

[@JesusSanchez-xu2is]

@@terrynaude284 tool holder bushing,but they have a flat and that's where you tighten the bore bar, ... If you try to clamp on boring bars with set screws it induces harmonics. www.roviproducts.com/tool-holder-bushings-and-boring-bar-sleeves/b-style-tool-holder-bushings/. Sure boring bars with flats are easier to center, but round shanks are the way to go for deep boring.

[@terrynaude284]

Jesus Sanchez thank you, it goes to show there’s so much more to learn. Blessings Terry, South Africa.

[@bigsmoke6189]

@@JesusSanchez-xu2is I've been using Sandvik silent tools for over ten years in clamped round tool holders and they are simply amazing ,as you point don't have clamp screws directly on the bar .also bars with flats perform better in round bushings.

[@GeneralG1810]

Now if only they could invent a boring bar you can use in a conventional lathe that you don’t have to pack to the max in the tool post to BARELY meet centre height!

[@GeneralG1810]

@TrashGamer-2020 Nah trust me man talk to conventional machinists. All of them will tell you about this problem, because carbide tools are designed mainly for use in CNC they design them for that and us conventional boys are left behind 8(

[@ChrisBrown-dy8ts]

I make up boring bar holders as I use a 50mm Dia bar in my quick change tool holders regular 👍

[@jarisipilainen3875]

0:29 yes thats what you sold before. best of the best.how we know this new is now last what we need? lol

[@---MarcosVanzuita---]

incrível esta ferramenta antivibração, muito show!!!!!!!

[@TungaloyCorporation]

sim! É uma ferramenta inovadora!

[@firstname_lastname3507]

Wow, I guess you could say this is pretty boring

[@Threat_LvL]

badum tsss

[@turolretar]

This tool could bore anyone to death

[@Honeybhai-wk7jr]

Can anyone tell me borung is single point ya multi point cutting tool

[@umarmujawar4461]

It's nice but I want the tool for SS material its bore dia is 10mm and tolerance is +- 0.008 micron with RA 0.

[@AlexMageethefirst]

then ream it.

[@MF175mp]

You're askin too much for most tools. 8 nanometers is a really tight tolerance

[@FireGodSpeed]

@@MF175mp +-8 so 16 microns

[@MF175mp]

@@FireGodSpeed I was joking, 0,008 microns is 8nm.

[@101picofarad]

What ~ price for this tool?

[@TungaloyCorporation]

Thank you for your interest in our tools. You can check the price from online shop of Tungaloy. If you have any further requests or questions, please feel free to contact us. Online shop : webshop.tungaloyamerica.com/search#/catalogue/group/1?kw=BoreMeister Web site : www.tungaloy.com/us/#

[@Mpm-bu4gy]

Donde venden

[@RealNotallGaming]

0:20 i have the second utensil strange but true is designed for finishing but is better at roughing best internal roughing utensil i have at work ^^ F0.16 mm ev with insert r0.8

[@mauryasatishc]

I want make a die total depth job profile 200 mm small dia 19.8 if possible please suggest me

[@kittycoma]

sandvik copy, i have tried both and this one pales in comparison

[@lalitkaushik6311]

I need this

[@davidwillard7334]

We'll go ! And buy one then !

[@dfergrg4053]

Character In the video It's great, I like it a lot $$

[@Michal_Sobierajski]

Just like Sandvik

[@gummel82]

Looks like a cheap sandvik knockoff

[@jagjeetsingh8587]

Very good

[@TungaloyCorporation]

Thank you!!

[@sandrobranco743]

Muito bom

[@КрасныйСерп]

дико сомневаюсь что это работает....а если звука и нет то отклонения от размера на таком вылете 100% сильно превышают норму!

[@chelowek_v_sibiri]

Читая такие комментарии за страну обидно. Брать иномарку или ладу тоже сомневаетесь? На счёт резцов - посмотрите различие в работе расточного из инструментальной стали и из высоколегированной, а также объясните как дребезг повышает чистоту обработки (исходя из вашего умозаключения)

[@КрасныйСерп]

@@chelowek_v_sibiri работал я и обычными резцами... и митсубишивскими резцами... и режимами играл... и скоростями... расточка свыше 100мм дает дробь на поверхности... не спорю возможно зависит от металла заготовки... от жесткости станка... и т. д.... но работая на мазаке и особенно на китайце... у нас возникали проблемы с внутрянкой глубже 100мм...

[@chelowek_v_sibiri]

@@КрасныйСерп возможно вы не так поняли габариты? Там резцы 3-5см. Видео от компании sandvik залиты на KZbin 8 лет назад, учитывая что сейчас есть такие видео от десятка компаний - технология точно используется. Особенно на горизонтально расточных, как я понял. Пока мы сомневаемся, предпочитая "кувалду и лом" технологии производства уходят семимильными шагами. А в наших институтах учат на перфоленте программировать.

[@КрасныйСерп]

@@chelowek_v_sibiri пересмотрел видео... теперь понятно в чем фишка резца... там компенсатор внутри стоит... он и резанирует при вибрации стабилизируя резец! почему то первый раз я не обратил внимание на него...

[@filvov]

Это работает. Я себе борштангу переделал по такому принципу, на вылет в 400мм, мелкая вибрация исчезла, можно сказать вообще. Сделал немного топорно, в следствии чего какие то отголоски остались, но качество поверхности в два три раза улучшилось точно.

[@thecreator6774]

I really like tools but i have no money for buy.

[@thecreator6774]

@TrashGamer-2020 yes bro

[@juanfranciscogonzalezcasal3757]

Lo confirmo los portaherramientas de mandrinar de tungaloy son bastante malas.... bibran una barbaridad.....

[@АлександрАнтонов-й1щ]

АМЦ такими резцами не проточишь

[@omega2845]

а что есть необходимость? Не протачивайте, точите по своей методе.

[@PhuongMai-nx8ex]

Character In the video It's great, I like it a lot $$

[@haivp.comvnpham9509]

Character In the video It's great, I like it a lot $$