Good stuff! I’ve been 8 miles offshore with one motor heading back and nothing better to do than diagnose the problem at 7 mph. It was a complete loss of power. Trim and everything! 115 Honda. 20 minutes later after going through the biggest fuse to the smallest it was....the smallest fuse that was the problem. 10 amp fuse shut the entire right engine down. I replaced that fuse 16 years ago and never had any problems.
@alfakrab61343 жыл бұрын
I just diagnosed this exact issue! 02 Vmax 150 carbd. I had Stuck poppet valve... removed calcification and greesed, also..5/16" ethanol damaged shredded line from primer bulb to engine was hidden in rigging trunk... upgraded to 3/8" (cut grommet at rigging trunk to make fit). Runs like a top now.
@davidwindhausen61943 жыл бұрын
Just got a marlin with a omc 115 took it out to find that at full speed the boat would fall on it's face . It was a rotten fuel line it was sucking air. CHECK YOUR FUEL LINES!
@Nonplused3 жыл бұрын
I once blamed my wife for power loss because she gained too much weight. She hit me. Turned out to be a spark plug wire fell off. Anyway start your analysis with the engine not your wife.
@CSJiGSaW083 жыл бұрын
LOL
@boashna3 жыл бұрын
what do I do if it was the wife ? . .get a divorce to get the top speed back .. how much that cost ?
@CSJiGSaW083 жыл бұрын
@@boashna You buy a bigger boat to make the center of gravity more efficient to your WOT top speed lol...
@erniemoore2365 Жыл бұрын
Your a brave man 😂
@pierredufresne6148 Жыл бұрын
Sound familiar 😅
@danielrobert71813 жыл бұрын
I found that a leaking fuel connector allowing air to seep in is also a very likely culprit. Check all connections frrom the tank all the way to the carb ... and be happy !
@RichaRat3 жыл бұрын
Good info. I did not know the trim sensor would cause that. The plastic strap with positioner on the rod that the motor pivots on broke and the trim gauge wasn't working. I replaced it before taking it out. Yamaha 200 HPDI
@john922143 жыл бұрын
An issue I ran into with reduced power was my belt going out on my 175 verado. I lost half my RPMs at WOT and didn’t know what caused it. No overheats or change in motor sound, just lost power. Having a broken belt causes the supercharger not to run, just decreasing the RPMs. A new belt and she was all fixed up.
@mikecurtis11113 жыл бұрын
Was out on the lake the other day, and was running WOT when my motor slowed from about 6200 RPM to 5000 RPM. It would run at the lower RPM for a few seconds, and then speed back up. This happened several different times over the first 15 to 20 min. Then I ran around pulling kids on a kneeboard, so we weren't running that fast. After a couple hours of moderate speed boating, I opened it back up to run back to the dock, and didn't have any more issues with the throttle. I'm guessing maybe I had some water in the gas.
@gabrielhernandez21043 жыл бұрын
This might help someone I had the same issue. I spend over a thousand dollars on parts thinking it was stator- trigger which had nothing I was getting water into the cowling so before buying anything make sure you check if you are getting water inside the cowling
@mikesolns13648 ай бұрын
How would water into the cowling cause that problem?
@HookedOnTuna3 жыл бұрын
Experienced the trim sender issue twice this week. Once on a verado and once on an evinrude G2. Glad to see you mentioned it. Completely ridiculous that this can put your boat into rpm reduction.
@johnurso5184 Жыл бұрын
Good stuff !! Excellent advice for any boater...This is why I do a spring make ready on my boats, first mechanically and then cosmetically. Then I do a late fall post season Mechanical before I put her to bed. You can still have problems, even with all that, but it will definitely reduce the chance of it.
@sketti7424 күн бұрын
Very informative video in a short time . Well done I am not getting full revs on one of my 70 hp 2022 Suzuki's. Runs fine just won't go over 3200 rpm for some reason now .
@BornAgainBoating19 күн бұрын
I'd check fuel system and fuel pressure
@Giovanni6993 ай бұрын
Don’t forget to check for a loose ground connection, had that happen to me 2 times one with a new engine install
@GameFishermen2 жыл бұрын
Optis and verados, thermostats. Being able to read temps and water pressure is a big thing. My verado wouldn’t get up to temp and had low water pressure. Pulled the thermostat and sure enough had issues with rocks in it
@Fireship13 жыл бұрын
Was cruising on the river for a few hours heading to open water and all at once my carbureted Yamaha150 just fell on its face. If I tried to go above 2,000 rpm she’d shut down. Come to find out the fuel line in the rigging tube had turned into bloated jelly. That and the heat from the sun made the line collapse. My engine was trying to drink through a straw that comes with a kids juice box. All new fuel lines and she was back to running like new. The morel of the story is change those fuel lines. If they are a few years old it’s time.
@Mike592153 жыл бұрын
Loss of power 09 Verado, Supercharger band snapped so it was sucking air. Easy fix once I had a hose clamp the right size when I got back. They don't sell those on the water. I keep a couple on the boat now. Also had an issue when the prop hub spun. No problem, I have an extra prop ready to go on the boat. Oh yeah, you need a prop wrench to change it out on the water! They also sell those in plastic so they don't rust, just not on the water.
@jayderwin13 жыл бұрын
If you have a 2 stroke triggers, CDI’s and power packs will kill your power because they are usually running on half the cylinders. I’ve had this happen with evinrudes, mercs, Yamaha’s and even a Kawasaki stand up jet ski.
@calespinosa39623 ай бұрын
My boat bogged down on me yesterday on my way to my fishing spot. The motor only has about 49 hours on it. I've had the boat for about a year already. I hope it's just my primer pump not passing fuel.
@floridaoutdooradventures89813 жыл бұрын
I had this problem. Mine happened to me this one time when I was going full throttle and out of a sudden, I started losing power. The boat would not go over 7 miles an hour and whenever I would try to go over 7 miles, the engine would just die on me! Turns out, I had water in the fuel system and I think I know how that happened. I believe after I got some gas at the gas station couple of weeks prior, I forgot to close the gas cap, came home and washed the boat with the fuel cap open. That's what happens when you rush things and have millions things in your mind... -:) Better to take it slow and focus on what you do. After that experience, I check the water fuel separator every so often and also add some fuel stabilizer to the gas tank if I don't use the boat for more than 2 months.
@L2fish3 жыл бұрын
So my 50 Merc which is a 1984 revved fine on muffs . Has rebuilt carbs by me, but has sat I don't know how long as I bought it used. Has all new trigger and ignition module. took it out first time Saturday and it wouldn't rev up. I was running an old metal tank and 5/16 line. I went to the marina to buy a new tank thinking that maybe the pickup on the tank is clogged. The marina told me that my motor takes a 3/8 inch line and that my old tank is made internally for a 5/16" line and probably not allowing enough fuel flow. So I bought new fuel lines too. Not sure if the motor runs off just fuel flow through the main jets at full throttle or if the float level maintains a full bowl. I dunno I am stumped. If this does not work I think I will check for a clogged exhaust and if not that compression
@phillipternullo49343 жыл бұрын
Years ago I replaced a COIL on a inboard engine with another bad COIL . That’s right the NEW COIL was bad . I wasn’t familiar with the boat and thought the boat was just underpowered. Until I saw an arc while I had the engine compartment open . I replaced the coil again and thought I gained at least 100 horse power : ) .
@pacificdynamicbuilders43803 жыл бұрын
The Yamaha 225 and 250 four-stroke have a filter inside the high pressure fuel pump that clogs up and kills your speed. Just thought I would throw that out there for people with those engines.
@dennismurphy32883 жыл бұрын
This happened to me on my 225 yamaha. Dirty filter screen on the high pressure fuel pump in the vapor separator tank. Was intermittent. Filter/screen had fine black dust covering it. Not sure how that would get through the fuel system unless it was hoses on the engine breaking down inside.
@joraanma262 жыл бұрын
@@dennismurphy3288 good to know I have the same engine having the same issue, will take a look at these things.
@joraanma262 жыл бұрын
Thanks good to know, some place to start my troubleshooting
@tomterrica4032 Жыл бұрын
Ethanol. @@dennismurphy3288
@robertpendzick92503 жыл бұрын
Was out on Lake Michigan, motor ran great, stopped, drifted, and then tried to restart, NOPE would not start, towed back to shore. Out of the water, went through the engine, fuel, plugs, screens, nearly everything, and all checked out, went back in, engine fully functional, never found the cause of problem, and never occurred again.
@lluisr.1853 жыл бұрын
Some months ago i got my rpms limited to 3000, because of the neutral position switch cable on the motor to the ecu was broken. Nice vid like always! Cheersssss
@BornAgainBoating3 жыл бұрын
Thanks for sharing
@northwestlife_93 жыл бұрын
Bad thermostat, causing overheating and low rpms. Excessive water in bilge causing sluggishness, turning issues, and slow to plane issues. 😞
@deathbeyondcompare3 жыл бұрын
One problem I had with my old Evinrude was prop shaft bearing
@osbornebay944 Жыл бұрын
The best engine tests for folks, thx a million. As a marine mechanic, those are valuable tips for most of the issues.
@bwagenberg3 жыл бұрын
I forgot. Why did you make the decision not to make videos about I/O engines and outdrives? Always LOVE your detail.
@anthonyraspantini66753 жыл бұрын
Do you have a video on how to test my relay for my fuel pump on my 200 Yamaha two-stroke
@rubendelatorre84033 жыл бұрын
Ver y good information. I just got the overheat alarm yesterday. Well kept 2019 Suzuki 140's. It slowed down at 5krpm.with heat alarm.Tween Vet 240 with 6 passengers. ???
@BornAgainBoating3 жыл бұрын
Thank you for your question! Please post it in our Born Again Boating Community! Go here and scroll down to access - it’s free: www.bornagainboating.com/
@ericdavi12313 жыл бұрын
Diesels love their oil like a sailor loves his rum! Gotta love captain Ron!!!
@crappycarracing3 жыл бұрын
I literally took my bass boat out yesterday it broke down. Get on KZbin today and see this video, maybe it’s a sign.
@pap91rt503 жыл бұрын
Another great lesson...mystro!!! I have a problem...I'm IO...
@edelpena86653 жыл бұрын
I wanna add one to the list ......a bad prop bushing ...that one is fun
@mikeweatherbee23 жыл бұрын
Don't forget primer bulbs. We were out on lake Erie and lost fuel pressure. I had my friend keep squeezing bulb so we can get back.
@stephenwaller3118 Жыл бұрын
With this issue need to be sure the gas tank is vented otherwise negative pressure builds up in the gas tank and doesn't allow adequate flow to the engine. By simply turning the vent knob on the gas cap flow is restored and voila, problem solved!
@mikeweatherbee2 Жыл бұрын
@stephenwaller3118 I own a Trophy WA with an 85 gal on board tank, and it's vented from the outside. The primer bulb failed to keep prime. We had to keep squeezing the bulb to get back. It's cheap insurance to keep one extra on board.
@Ronilac Жыл бұрын
Closed or clogged fuel tank vent... the first thing to check.
@claudew55823 жыл бұрын
Would you know if a 2013, 90hp mercury outboard 4 stroke # 1B986113 has that trim sensor. Motor misses at idle and “bucks” when trying to get on plane, but no alarms. Motor has been at the dealership for about a month, they have ran fuel, electronics, compression and water test. They “think” it’s a faulty ecm.$$$ BTW, very informative videos
@pipermang3 жыл бұрын
I had a power loss problem on my 2000 mercury efi. It would max out at 3500 rpms then jump to WOT out of nowhere. Found a loose hose clamp at the water separator. I suspect the small fuel leak was letting air into the system?
@BornAgainBoating3 жыл бұрын
Thank you for your question! Please post it in our Born Again Boating Community! Go here and scroll down to access - it’s free: www.bornagainboating.com/
@rcl35143 жыл бұрын
Had a 40 hp carbed Yamaha run off a 6 gallon poly tank, on a 13 foot Del Quay Dory. Engine would idle fine out of the canal for the 10 minute or so run but after 2 minutes or so of wot, would die like someone turned the key off. Would start right back up like nothing was wrong. Checked the vent valve, nothing wrong there. Played around with it for little while and figured out that the fuel pick up assembly on the tank, the gasket had failed, so when we would push the throttle down, the fuel pump couldnt pull enough fuel thru the hose, because the gasket was allowing too much air into the tank, and not creating a little bit of a vacuum that the engine needed to run
@mr.cryptobull15206 ай бұрын
I don't think you realized it.. but I'm guessing your pick up tube was loose and you pushed it in tighter without even realizing you did it
@rcl35146 ай бұрын
@mr.cryptobull1520 nope. 6 gallon portable tank. What we think happened was over time the seal on the portable tank assembly went bad. The tip off was there was fuel under the area where fuel line plugs into the tank. It was all plastic. Put a different tank on it and the problem went away. At idle, it was fine, but under speed conditions the top would start to pull air and the engine would loose it's prime.
@sneal777773 жыл бұрын
I don’t know how you could have a boat with a fuel water separating filter that doesn’t have a see thru bottom sight glass
@bottomknockinbaja60923 жыл бұрын
OMG!! THAT BOAT BOTTOM AT 1:03!! I thought I was at the Aquarium! Lol
@PFLEONARDI09063 жыл бұрын
Regarding the hull parasites, if you have zebra mussels use hot water (140F) to get them off the hull. I f you find zebra mussels in your bilge, baitwells, or other compartments use hot -120F water. This references the ABYC/manufacturers testing parameters to prevent damage to bilge pumps, etc. Thanks for these excellent videos... I know you are working on a troubleshooting checklist ;)
@ryantait1772 ай бұрын
Hi. Thank you for the great vid. My 115 Mercury Optimax was standing for about 7 months with about 4 flushes over that period. I took it to the river over the weekend and for some reason it is in limp mode. No alarms just limp mode. Any help?
@BornAgainBoatingАй бұрын
Could be anything but I would start with checking out your fuel here's some videos: kzbin.info/aero/PLDFOb030syP4fpLlxGN3EH7gmSUb1VFS3
@ryantait177Ай бұрын
Thanks
@catallaxy20003 жыл бұрын
Yamaha HPDIs drop two cylinders in neutral... If the shift position switch sticks, you can run in gear on four cylinders instead of six... Ask me how I know this... 😕
@mikeprince54593 жыл бұрын
Had that too.
@RichaRat3 жыл бұрын
Thanks so much for that tip.
@ellisd4529Ай бұрын
This was great knowledge. Thank you
@melinda57773 жыл бұрын
Great video! I gotta save this and watch it again! Very informative!
@BornAgainBoating3 жыл бұрын
Glad you enjoyed it!
@markdavis209011 ай бұрын
My Mercury 2 stroke 90hp 2009 3 cylinder will idle great at the right rpm. But when throttling up the motor begins to spit and sputter and begins to pop out of the prop exhaust. Waiting on jets. That what is left to change everything else checks out. In the video I see a round plastic screen. I wonder if I have one of those on my engine and where would it be located.
@nazarsulaimanbekov42094 ай бұрын
Did you figure out what is was? I have the same engine. It idles fine, but doesn't rev up. Cleaned up fuel system, replaced all filters, still nothing.
@PETERVITELLO Жыл бұрын
HELP! I have a 2007 Boston Whaler with a 2007 Mercury 25 HP engine. The engine starts and runs well but will not plane. When in neutral, the RPM's go up to 5k with out hesitation however, when in gear under load, it refuses to go over 2500 RPM's. I've replaced and updated several parts with zero change in performance. Those improvements are as follows: prop, water pump, fuel injectors, spark plugs, fuel filter, oil filter, thermostat, fuel tank and fuel line. Had the VST looked at as well and checks out. Please help! We have a very small window of time to enjoy the ocean here in Massachusetts and the window is closing. Thank you!
@Redbird453 күн бұрын
We have a boat with an I/O and it gets so gross you can’t even see the paint on the outdrive 😂
@mgshoe45263 жыл бұрын
Anyone have a recommendation on a good mechanic located in either the Ft Myers or Stuart, Fl area? Trying to keep the Florida boating dream alive while out of state. Engine is a 2005 Mercruiser 5.0 MPI, I/O. 260 hp. Thanks.
@TheBenbeyer3 жыл бұрын
All the growth on the one hull can be power washed off? That was a crazy amount of sea life on that boat!
@zacpearson18783 жыл бұрын
Bad gas, bad lines, missing hose clamps, primer ball, cracked cylinder, and old fuel filters are all problems I’ve un into on my engine aside from electrical
@stevenyoung80385 ай бұрын
I hit a big wave and lost power, but I’m confused because it idles fine. You can rev it up in idle. It’s not getting hot or it’s not smoking but when you put it in gear, it just loses power and dies.
@BornAgainBoating5 ай бұрын
Really hard to say, could be anything depending on the engine model and type. Fuel, spark, who knows, not much info my man
@robertlatham49513 жыл бұрын
just bought my first boat. I need videos for I/O engines.
@pap91rt503 жыл бұрын
Don't exist...unfortunately...love this guy!!
@claudequeen66143 жыл бұрын
I got a 1980 735 horsepower Mercury and it was running great and all the sudden it started running on one cylinder the bottom plug ain't firing what should I do I re checked the car decors fired so what should I do can you come at me back and let me know thank you and have a blessed day and be safe
@claudequeen66143 жыл бұрын
I was hoping you would tell me what it would be on a 35 horsepower Mercury thank you and have a blessed night
@whiskybravomike24863 жыл бұрын
Wish I had this video 6 months ago lol. I had the trim sensor issue.
@glengilliam99993 жыл бұрын
Great video, please keep them coming.
@glengilliam99993 жыл бұрын
Do you have any videos of sterndrive boats.?
@imurtroll52423 жыл бұрын
Awesome video with great content, thanks for everything
@Dademold2 жыл бұрын
Great videos do you guys have a shop ??
@MrMoosekiller312 жыл бұрын
Mine runs great on the trailer it's when I put boat in water it's starts fine you put it in gear and that's about all the revs I get 70hp troliing motor lol it opened up a couple times during the summer for about a mile or 2 than back to trolling spped I changed coils all 3 and plugs I'm stumped had it running 2hrs with the muffs temperature is fine rpm good throttle opens up put it in water back to troliing speed this is the first time I have a problem with something and have not found the solution online and I've looked several times it's been a year since I last looked so I'm giving it another shot before this summer has come an gone an hopefully I can go enjoy some time on the lake again I bought this motor off a landlord who said someone left it behind 70hp evinrude middle to late 70s the mechanic who installed it said it looks all rebuilt it has all gaskets unfortunately his shop burnt down recently and no marine mechanic within 100km of my place so hopefully your video gives me a clue as too what it might be watching er now cheers
@jbettss3 жыл бұрын
Captain Ron is a great movie.
@jamesrahn83393 жыл бұрын
This is gold...thank you again
@BornAgainBoating3 жыл бұрын
You bet!
@penny2001003 жыл бұрын
Please Talk To Us About Gear Ratios - Power Head Revolutions Per Minute Vs. Propeller Revolutions Per Minute. Also Include The Differences Between Diesel Power Vs. Gasoline Power as Far as Torque is Concerned. That Should Make Very Interesting Viewing, Thanks Mate!
@C5drummer3 жыл бұрын
Ahhh, yes the pee hole issue...In July 2018, had a mud dauber make a home out of my engine's little urethra that ruined a planned offshore trip with 2 bathing suit female friends to the Middle Grounds...The day got scrapped till 3 weeks later and I spend 3 hours clearing one of the hardest substances known to man...A Mud Daubers mud nest! Luckily, 3 weeks later was an amazing day, but that day was gonna be epic...and it wasn't.
@sunayrobinson83813 жыл бұрын
Summer is here again with the restriction of movement of and recess to be enjoyed by most workers. ;It's an opportunity to utilize and redirect this funds into life changing investments as to secure financial sustainability!!!!
@amberleonacoakley32253 жыл бұрын
I have secured financial freedom myself investing in bonds , equities , EFT's and some digital currencies .
@nikonovsergey76063 жыл бұрын
I wanted to invest more in Crypto but I got caught up in the dip so bad so I had to dump
@alissacampbell43773 жыл бұрын
After the dip in price of Cryptocurrency from a higher level, some traders and investors view this as an advantageous time to buy or add to an existing position, I'd advice family and friends to trade rather than holding, because buying and holding doesn't guarantee maximum profit.
@lucaslewis38803 жыл бұрын
@@nikonovsergey7606 that's why you need the help of a professional who trade and understand the market more to earn good income.
@carinalopez19253 жыл бұрын
@@lucaslewis3880 These professionals understand the markets like it's there own farm and makes maximum profits for investors
@lachyelmulatiko74353 жыл бұрын
So i have a question i have a 2004 yamaha 225 4 stroke with 420hrs, i was running offshore hit a wave and the engine rpm and speed drop, my alarm came on, i shut it off and back on with out any problem, it has done it like 5 times, what can i look at, i checked my oil level and is good, and this is something that just started doing
@tonchido3 жыл бұрын
You can check outboard height,when wave hits you it can dlow you down and prop loose grip,and starzs to ventilate.you have to lowrr rpm and get on plane again.
@lachyelmulatiko74353 жыл бұрын
@@tonchido this just started happening, is kind of weird to be honest
@JesusVargas-lr4yo3 жыл бұрын
2002 mercury 200hp saltwater outboard 4 beeping alarm run un high rpm went lower beeps and lost full power
@JesusVargas-lr4yo3 жыл бұрын
Any recommendations I watch all you videos and thank you very much
@1ruppenkamp3 жыл бұрын
Had lose of power for loose connection on battery disconnect
@UltraMagaFan3 жыл бұрын
We have a 23 horsepower Vanguard on a Go Devil long tail that was loosing power because the hose that runs from the cylinder to the fuel pump was old and had a crack in it. I don't know if this is the case for the newer ones (ours is 32 years old) but it does not like to run on low fuel pressure. I'm not complaining when there's no problems this thing runs like its brand new but Id like to get one of the new fuel injected Vanguards and a new long tail. Unfortunately we do not have the money to buy a $5000 motor mainly because we just got a 1999 Key West 210 Bay Reef that is in immaculate condition for $6500. (it was a steal we got lucky)
@jasonbarrett61842 ай бұрын
I have a 25 horsepower Evinrude. In the first time I took the bolt out the first 5 minutes. The engine was running perfectly and after that it just will not go over 5 mi an hour for some reason. Do anybody have a clue what the situation is
@BornAgainBoating2 ай бұрын
Most likely fuel issues: kzbin.info/www/bejne/oWildaSOe9mMe8Usi=kC7ozMvmQ48YkpHA kzbin.info/www/bejne/m4uriadjhsmZhK8
@marshall6604 Жыл бұрын
1. Run out of gas. 2. Prop falls off. 3. Stuck in reverse. 4. Locked in the garage by Greta. 5. Voted out of office.
@MichaelOrtega-k8i11 ай бұрын
Hi I lose some times power on mi ya Maha 2 stroke 60hp wen I just go aut of the dock but after probably 20 minutes it fixed and starts running good wat it the issue
@marlonm3963 жыл бұрын
My head is spinning of all of these potential troubleshooting steps. I got BoatUS printed on my forehead.
@boaterbil3 жыл бұрын
Ok, so your offshore and have a misfire. You pull coil wires and see #2 does not change. #1 DONOT unplug with engine running! #2 now you know #2 is misfiring, What are you going to do about it???????????
@boashna3 жыл бұрын
you know that it is not going to get worse and may find a rpms sweet spot for max power. if it is a clogged fuel filter it may get worse .I am not a fan of diagnostic in the ocean.
@timw8796 Жыл бұрын
Man I have a 2016 mercury 150xl 4s with 90hrs on it. It will not go past 3800 rpms or over 9mph I have no clue what could be the issue.
@Talzfishing-gc243 ай бұрын
Hey guys I have an evinrude ficht that bogs when I accelerate but reaches top rpm any advice on what to do? I had to put a temporary in line fuel filter could that be starving my engine?
@BornAgainBoating3 ай бұрын
Shouldn't be, you should have a fuel filter in the boat for sure! But sounds like a different issue with the engine. Timing advance, TPS, fuel injection issue, not really sure, could be a lot of things, but you can bypass the fuel filter and test if you want, but I doubt the fuel filter is your issue :/
@Talzfishing-gc243 ай бұрын
@@BornAgainBoating hey thanks for the reply is it common for injectors to be blocked and if so can I use the method you had In your video using the little 12v battery?
@Talzfishing-gc243 ай бұрын
I can't seem to find a mechanic who will service it
@scooter81873 жыл бұрын
I have a 2-year old (220 hours) Mercury 150 4-stroke that has run flawlessly until about a month ago. Now, the first time during each trip that I accelerate to get up on a plane, the engine shutters as it climbs to higher (around 4K) rpm's' for a few minutes and won't reach max rpm's. After that, it runs perfectly for the rest of the day, even at full throttle/5500 rpm's, and even after stopping and starting. I use the boat about once a week and only use ethanol fuel. I know it's covered by warranty, but I like to take care of this kind of stuff myself. The fuel filter was changed at 100 hour service and it doesn't have a separate fuel/water separator. I'm wondering if it could be a venting issue.
@tractorguru81683 жыл бұрын
Why do you only use ethanol fuel?
@scooter81873 жыл бұрын
@@tractorguru8168 Sorry I meant non-ethanol only
@markdrabik93123 жыл бұрын
Did you find the issue? I’m having the same problem with a 150 hp Mercury 4 stroke
@scooter81873 жыл бұрын
@@markdrabik9312 I thought I had found the issue...lack of good fuel tank ventilation. When I remove the gas cap, I get a very significant wooshing sound like the tank has a lot of pressure (or maybe vacuum). Based on some things that I read online I thought that might have been the problem but when I contacted the dealer who sold me the boat they said that my fuel system is pressurized by design and should do that. I did experiment with taking the cap off to release pressure when I was having the engine shuttering problem but it didn't seem to help. More recently I am wondering if the problem could be related to ventilation in the cooling system. I noticed that if I accelerated to plane from slow speed with the engine trimmed up too high, the engine would briefly ventilate. As soon as I hear that sound I trim the engine down but I get the engine shutter for a while after that. I'm wondering if the shuttering could be related to having some air in the cooling system and then the engine limits RPM's until it senses good waterflow. I've never heard of that before, but there does seem to be a correlation between those two things happening.
@swhite12 Жыл бұрын
Hello my 50 4 stroke motor mercury can't get power after sinked in water
@OZD-mb2bs Жыл бұрын
These video's are awesome! Great job!
@joelubin5479 Жыл бұрын
Terrific , what about a power head ?
@duro8453 жыл бұрын
What's a bote?
@marcoshi23 Жыл бұрын
I've got a yamaha80efi engine. which runs quite well. I have one issue which i cant seem to find the problem for. after running it for a good while and trying to get back to the harbour, it seems to have problems to stay in lower rpms. this problem does not happen when i leave the harbour. any ideas? greetings from Germany! :)
@odinsteinnes65113 жыл бұрын
I take my bout out of the water at the end of the season to clean and wax it so its ready for the next season
@je7758 Жыл бұрын
I have Yamaha 2012 f350 dies after 15 seconds?
@BornAgainBoating Жыл бұрын
No idea, maybe fuel :/
@louisstellini77118 ай бұрын
Very good and much much knowledge thank you
@BornAgainBoating8 ай бұрын
Most welcome
@cmacedo11773 жыл бұрын
Very good advices, thaks
@BornAgainBoating3 жыл бұрын
thank you
@fernandofolgueira51913 жыл бұрын
Excellent video for all of us
@darreldavis6145 Жыл бұрын
I have a 2018 mercury verardo its putting a lot of gas in crankcase every time I use it can anyone help it only has 15 hours on it
@813_racing33 жыл бұрын
Hey man what would be a reason that my rpm jump and down and the boat would lose power and die been kicking my ass change a few thing already if you ever had that go on in mercury optimax 200
@jonnyglez35303 жыл бұрын
Another great video 👍
@BornAgainBoating3 жыл бұрын
Glad you enjoyed it
@majorpain87723 жыл бұрын
Throttle position sensor module going bad causes the same problem.
@timbonaparte5120 Жыл бұрын
I have a problem my optimax is going for a 1h and then it dies the buzzer won't sond an the fule pump won't start need to wait 10-20 min so it cools off to start it again do anybody no the problem?
@earldaisgomez39593 жыл бұрын
Dear sir. Greetings. Good lessons
@BornAgainBoating3 жыл бұрын
So nice of you
@UrbanFisherman3 жыл бұрын
Awesome video 📹
@BornAgainBoating3 жыл бұрын
Thanks for the visit
@wolfpackflt670 Жыл бұрын
You failed to mention to check the thermostat to see if it's stuck closed causing an overheating issue.
@unisuit9 ай бұрын
Spun wheel hub?
@teachingrounds3 жыл бұрын
Super information
@BornAgainBoating3 жыл бұрын
Thank you
@MrMorbo4203 жыл бұрын
I have had power pack problems this season. its been crappy.
@alexppp2303 жыл бұрын
Man I would like to have you on my boat all the time I have my boat in the watere🤣