Bosch GBH 2-24 DSR disassemble field o-rings grease hammer

[@schmuhf]

Thank you for the video. I was scratching my head a little because I have all the fresh O-rings ready on the bench, but couldn't figure out how to replace the ones inside the tool holder. Your video should help me remove the lock ring and get that sorted out. Once I've done that, the 2-24 should be ready to rock once again.

[@ايمنالمؤذن]

thank you so much Today I repaired GBH2-22RE ,GBH2-26DFR The credit goes back to you I wish you success Dear Engineer

[@ايمنالمؤذن]

Hammer Piston O-Ring groove ball bearing Striker Pin Ø7,5 MM

[@ايمنالمؤذن]

I am a new engineer at the Bosch branch in my country

[@strummer6642]

Good basic teardown video

[@IsrarAhmad-en3sn]

Can I apply lubricant if the moter is rusted

[@sdnicolash183]

Excellent videos, thanks for the help.

[@3103dario]

Excellent videos.... Thanks

[@handyman7282]

Thank you

[@okiheh]

Thx for this it helped a lot :)

[@MoTourCu]

Thanks bro.

[@Sachertortehmmlecker]

Which Torx size have the screws?

[@suleymanbelik9803]

Very good..

[@a125aa]

Good video where part two?

[@alexandrucsomos3541]

hi, i have a problem with my drill, sometimes when i need to drill in masonry and i put my drill on drill and hammer position my drill make a bad noise and i cannot drill in masonry then i need to turn again to only the position and try again maybe a couple of times until it work. do you know what could be the problem? after i watched your video i'll try to disassemble my drill next week thanks for all your videos

[@mariusz1586]

hello, could you help me?, my bosch GBH 2-24 after switching on loses power and slows down to almost zero, and smell a little from the engine , Brushes look good, what could be the reason for this? best regards.

[@handyman7282]

Hello, it can be armature or field bured out. Armature comutator may look dark or have burn marks. Andcyiu need to check armature bearings

[@suatozturk9927]

İyi günler bende dre 2 26 var sıkıntısı motor çalışıyor fakat kırıcı delici vede darbeli delici çalışmıyo

[@dabiensalain3832]

Nickel vos commentaires Une deuxième vie pour un perfo

[@rafthbib]

👍thanks for you

[@SharkStudio]

I have a same bosch hammer like this. The porblem is my hammer is shoot the oil from middle. Could you help me how can i fix my lovely hammer? Thanks.

[@handyman7282]

You have overheated it. You need to clean it, change oil and oil seal.

[@TheHeisenberg1970]

@@handyman7282 : Which Oil? I saw only grease. Can I use silicon grease for lubrication? You mean the seal of the gearbox towards the motor?

[@jonedwards7824]

Great videos, thanks for the help. Are you based in the U.K? Do you do a repair service?

[@fabioosoriobetancur822]

Jon Edwards solo me sirve el percutor!!! Que puedo hacer?

[@nabilelmahjoub7413]

Bien

[@gdlbarax7027]

Top

[@vindodasaguasescuras]

Como sempre, os americanos cheios de frescura até pra desmontar uma máquina de furar🙅🙅

[@user-fb9on1zc2h]

ок ок ок 😂😂😂😀

[@robertohurtado2758]

Explicacion en castellano

[@geovanesilva3540]

já começou fazendo merda. em bater a carcaça do motor pra tirar o estator

[@lazarsamardzic3654]

Ću ću

[@lamalama6286]

.