Bosch/Siemens Tumble Dryer Not Heating or Drying Clothes

[@petitprince05]

You're a legend. Thank you so much for the crystal clear explanations and showing how to strip & test every step of the way.

[@d.mmaropack1480]

Good explain.

[@stevandjes]

Have you ever change a temperature sensor F2 fault on a Miele tkr650 wp. Thinks it’s the one just below the door? Thanks

[@murate6029]

I have Siemens Iq series, it stopped working no lights no power. I got the pbc changed now it works but stops after 20 minutes and gives the waterbox full signal, although it is completely empty and the water pump works. Do you think they placed the wrong pbc on the power card? Thanks for the excellent videos

[@MultiSchatzi123]

hi how-2-repair. do u have any videos about bosch dryer serie 2, ( belt replacement)? i cant find anywhere. by the way, your videos are awesome. thanks.

[@samweston7779]

This was a great video, explained very clearly. I'm currently trying to troubleshoot my Bosch dryer which is presenting an E09 error, which I understand is a error in the heating circuit. I tested each of the components as you demonstrated here and I observed the correct results. Do you have any recommendations on what I should try next?

[@How-to-repair]

Hi Sam, to be able to help you properly I need a little bit more detail. You have not included the model number on your machine. You can either send it across here, although it's a proper contact form at the website where I would be able to upload exploded diagrams or anything else I find once I have the model number @samweston7779 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@hosamajram1164]

Nice explation 🎉🎉🎉🎉🎉🎉🎉🎉

[@How-to-repair]

Thank you

[@dashcamdriver9126]

Great Channel - Hoping you might be able to help. I have a WTW87560GB/02 Condensing/Heat Pump dryer which is not getting clothes dry. Initial problem was that the dryer was not working - kept giving E-90 code. I isolated it to a faulty relay on the power board and replaced the relay. It is possible that one of the adjacent relays has also been affected and so I have ordered more relays. I took the machine apart and cleaned all the lint out included from the front of the condenser and evaporator. I checked the pump resistance (170 Ohms). Finally I've run the various test modes (all 28) and the only issue I could find is several of the tests stop after 5 seconds with E-14 and -00. I can't find anything online detailing the test modes or resulting error codes. Any advice on what to look for?

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@dashcamdriver9126]

@@How-to-repair Thanks - subscribed and message sent.

[@shaysinay]

Hi there, I was wondering if you could please advise me about a a BOSCH thumble dryer (maXX 7 sensetive) that wont heat up. I cheaked the thermostat for continuety - its fine. The NTC sensor which is located at the back of the heating unit - fine. The microswitch (tny266gn) - fine. The heating element values - fine (30 Ohm for one coil, 42 ohm for the other coil). no visible damage or tear. Although everything seems fine, the heating elemet isnt getting hot enough, and the drying cycle ends with damp (yet hot) cloths. Could you please help me solve the issue? Many thanks.

[@How-to-repair]

Hi, please use our contact us page and make sure you fill out the request for what your problem is. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@shaysinay]

@@How-to-repair Thank you for your replay. I have filled out the proper request, as mentioned. cheers.

[@shahidabbas5830]

🌹