How to machine a brake drum on an ammco brake lathe.
Пікірлер: 29
@HienHuaaaa8 жыл бұрын
I'm at work doing rear drums right now. I had to look on youtube to figure out how to use this again. It's been probably couple years since i've cut drums lol. Thanks again!
@jmmcdon255 жыл бұрын
Thank you. You are a very good instructor. well done!
@Destiny-tg8mo6 жыл бұрын
Nice video it's been 30 years sense I used one of these Ammcos .Took a automotive class in 10th grade of high school I remember being fascinated with the machine.So I picked one up for my personal garage.Great overview .Thanks
@7Westwood2 жыл бұрын
Great Video, Thanks for sharing your knowledge.
@bruceo19873 жыл бұрын
If the drum measured 188mm and the spec is 227mm then the drum seems well under spec, ok to turn.
@mtejada18 жыл бұрын
Great video!!! A have a lab tomorrow where I have to do this. I have already done the on car lathe which was extremely easy, I have also done it on this same mechine but resurfacing a rotor.
@myastlabhelper8 жыл бұрын
+Mario Tejada. Thanks Mario, I'm glad I could help.
@9traktor3 жыл бұрын
What a workshop! Fine!
@fbgm_yousef91832 жыл бұрын
I wish my teacher was as thorough as you
@unclegreybeard39692 жыл бұрын
What type of cutting tips do you use and how many drums can they cut before needing to be replaced?
@lesthomas58316 жыл бұрын
What do you think about the quick change chuck
@lesthomas58316 жыл бұрын
Have you ever seen the small drum tip for doing small brake drums
@idahormj667 жыл бұрын
I enjoyed your video but never thought you were in Kuwait, maybe the moon but im not sure
@smileyrod118 жыл бұрын
do you still teath class let me know thank
@decentcngworks.52318 жыл бұрын
nice video good iam asif from mumbai india i want thish machene how much
@Cheepauctioncars4 жыл бұрын
Whare can i get this done
@eduardovarela2319 Жыл бұрын
Bery intrusted thanks.
@Cheepauctioncars4 жыл бұрын
Live in nj
@shaheebshahid84882 жыл бұрын
Why use belt on drum
@bernardinovillalobos14832 жыл бұрын
Posi como dijo mila
@steveu2358 жыл бұрын
lot of stuff to go through to use a brake lathe I do them on my engine lathe with a shaft and centering cone and that's it..
@ragibsaba84879 жыл бұрын
Hi.. Sir where is your agency in kuwait. I need your address.
@myastlabhelper8 жыл бұрын
Sorry, I'm located in the US. I'll be posting lots of new video's this fall and winter so stop back and thanks for watching.
@myastlabhelper8 жыл бұрын
+Ragib Saba Sorry Ragib, I'm not in Kuwait. Let me know which video helped and if you would like to see others in the future. Glad to help.
@lesthomas58316 жыл бұрын
If you can the quick chuck makes thing easier when mounting a rotor or drum have you ever see the small drum tip for small brake drums
@fathieljali20585 жыл бұрын
Great job sir Where can i get like that machine. Thanks
@aidanlyons11554 жыл бұрын
Fathi Eljali hi, I can get you one of these lathes. Shipping to you may be expensive though. Let me know