1978 Evinrude 85 HP - Carburetors and Fuel Lines

  Рет қаралды 81,893

Brandon's Garage

Brandon's Garage

Күн бұрын

Пікірлер: 90
@osbornebay944
@osbornebay944 3 жыл бұрын
Can t stop watching your vid for oldies. I got a 70 Evinrude 85 hp. very low hour , 1-200 hrs, compressions 148-151 lbs cold. Working on sparks.....
@brianstinson5865
@brianstinson5865 Жыл бұрын
About to do this on a 1979 100hp Evinrude. I have no mechanical skills but your video has given me the confidence to take this job on. Thank you!
@Zach-uy8ny
@Zach-uy8ny 4 жыл бұрын
Great video. Love how you get straight to the point and keep it moving. You don't get hung up on the little stuff like not having a specific tool etc. - and no fluff. Thank you
@rafg2857
@rafg2857 4 жыл бұрын
Dude, you make Great self-help instructional videos. Even the haters pretty much leave you alone. You Da Man! Thank you.
@redgreen610
@redgreen610 3 жыл бұрын
Just doing the same job on 1971 85hp Johnson. Thanks for posting. It's been about 30 years since I've rebuilt a carb. I think the line going from the fuel pump to the crank case is the source of positive an negative pressure that runs the pump...pretty sure these were never engineered with efficiency and emissions in mind! But that old engine still starts with the first crank. Had to rebuild the transom and all stringers in boat, so thought I'd rebuild the carbs this winter because I think idle jets are worn (original carb, never rebuilt).
@Troys221
@Troys221 4 жыл бұрын
Hi Brandon, I have the exact motor & have done everything you have done. The only difference is is when cleaning my choke solenoid it has a spring in it between the solenoid piston & the solenoid itself. I checked my 74 evinrude solenoid (older 3 wire) & it also has a spring. I know it's an older video but I thought it would help by posting my findings. Both choke solenoids work as they should, no sticking. The motor runs great after doing exactly what you did.
@zacheliasjacobson1115
@zacheliasjacobson1115 3 жыл бұрын
I'm trying to bring the same motor back from the dead you're video has helped alot thankyou
@toddmaki2959
@toddmaki2959 4 жыл бұрын
Thanks for the video. I'm tackling this project today. Watching a few youtube videos before doing a project really makes it go smoother!
@timkrull7237
@timkrull7237 Жыл бұрын
I’ve been having problems I watched this and I missed the little port in the bowl I was not getting gas too one cylinder thanks video saved me
@jacklowe3788
@jacklowe3788 6 ай бұрын
Those old 85's are strong motors!
@normandunnaganjr.5034
@normandunnaganjr.5034 5 жыл бұрын
Thanks Brandon. I recently bought my first boat and it's got a 15hp 76 Evinrude. I just post a video with it, I'm impressed by the condition of the engine and how it runs still. Watching your videos and trying to learn more about carbs, mine idles a little weird but runs well-
@Steve-wz5pz
@Steve-wz5pz Жыл бұрын
Ultra sonic cleaner works a treat on clearing out those clogged carbs, and you do not need toxic/caustic chemicals.
@Will_Russell
@Will_Russell 6 жыл бұрын
Does the carb cleaner not damage the plastic bits on the throttle linkages?
@wlukew3052
@wlukew3052 6 ай бұрын
Hi I have a quick question about needle valve placement, rubber up or down thanks
@wlukew3052
@wlukew3052 6 ай бұрын
Looks like you put rubber in first
@ksfishingadventures
@ksfishingadventures 3 жыл бұрын
How are the gaskets ? I saw other kits on Amazon and the reviews say the gasket gets all warped after 2-3 uses of the motor cause ig fueling issues
@a7mad421
@a7mad421 Жыл бұрын
Do you have a video of you removing the carburetors?
@fredhuang9223
@fredhuang9223 Жыл бұрын
Informative! Brandon do you know what those two brass tubes are in front of the carb? Mine spews out fuel and the needle and seat seem fine...
@BrandonsGarage
@BrandonsGarage 10 ай бұрын
Pretty sure the evinrude carb video showed how to test and fix that problem.
@markromero634
@markromero634 3 жыл бұрын
The drain valve on your float bowl is brass or plastic? Mine are plastic and cracked and leaking, wondering if brass replacements are sold.
@themostexcellentadventure5473
@themostexcellentadventure5473 5 жыл бұрын
Excellent video. I am working on a 85hp Johnson. Looks very similar to this one. I have never worked on an engine with a carb. I am getting the manual for it soon. Mine runs then revs up really high at idle. I am noticing there is a lot of fuel in the intake area just before the butterfly’s. I noticed this when I took the intake cover off. Floats don’t make sense to me right now because what if the engine is not level, like the trim is not flat, wouldn’t it not be working properly? I think something is going on with my floats because this seems to be the only thing controlling fuel delivery. As for the measurements of the float travel the important part would be at the closing point. Need to make sure that is closing at flat position. The other direction seem to not matter to much as long as it gets full travel to bottom of the bowl. Would this be correct? Thanks for making these vids.
@Z-Ack
@Z-Ack 4 жыл бұрын
I got a 79 100hp and is leaking gas, looks like it builds up in the breather cover from the looks.. does that just mean the needles getting stuck and overflowing/ overfilling the carbs? Ive ran the motor with no issues for years but always had the fuel leak and tired if the gas headache and risking a mid lake fire.. it has started to get bad enough that when you cut it off you can see the gas mix run down the outside of the lower unit from pooling up in the motor case so much.. like i said though runs fine. Idles smooth at 800 and high throttle it pushes me about 50mph on my ole dynatrak.. hoping replacing everything in the carbs and gaskets will stop the gas leak.. gotta get it all ship shape to sell it to pay for my funeral. A quick reply would be awesome as i got to get everything done before my strength goes. They stopped my radiation other day so guess im pretty ate up inside.. Ps. Spend half of life learning so the other half can be spent teaching. Thoughts die but words can live on...
@michaelgreene7385
@michaelgreene7385 4 жыл бұрын
Prayers be with you brother....
@Z-Ack
@Z-Ack Жыл бұрын
Im still here! So those prayers helped.. minus half a stomach, colon and worst part is they took my left nut.. that crap will make you walk funny for a while.. never sold the boat either, couldnt find a buyer but things still leaking gas..
@Table1000
@Table1000 2 жыл бұрын
I have a 115 hp crossflow V4. 4200rpms it would act like it ran out of gas. 4000 rmps runs perfect all day. I replaced and tightened all the lines up. Replaced all coils with oem. The vro is deleted. Now will run great till 4200rpms. 4300 it hits a wall and not as smooth sounding. What do you think? Fuel pump? High speed jets?
@BrandonsGarage
@BrandonsGarage 2 жыл бұрын
All of the above. But, if you pump, you would have a few seconds until it ran out of gas. Then jets or timing.
@Table1000
@Table1000 2 жыл бұрын
@@BrandonsGarage Do you think it could be over propped? 19.6 ft, 14 inch/ 17 pitch aluminum prop. Thanks for the replies
@cjballard87
@cjballard87 3 жыл бұрын
Hey sir, I have a 1976 Johnson 115 V4 and need to replace the whole fuel system. Would this club kit also work on my motor?
@robertoswald2321
@robertoswald2321 6 жыл бұрын
Thank you for the info. I'm new to boats . have a 1978 115 evenrude hard start cold have to idle up when going into neutral even warm . are all the adjustments done in the linkage? Iv set carbs on old VW bugs and dirt bikes . I don't see u set any air fuel stuff any info would be much appreciated thank you for your content
@robertoswald2321
@robertoswald2321 6 жыл бұрын
Also choke solenoid inop so ill surely try my power probe on it before and after the rebuild u just showed. But even manual choke still hard start ether only
@ct1762
@ct1762 5 жыл бұрын
you won't see any air-fuel needles because, and this is the best part: nothing to adjust with FIXED jets! So really just make sure they are absolutely clean and you are good to go.
@codys3975
@codys3975 4 жыл бұрын
I know this is a old video. I got the same motor this is my first boat when I tried to clean the carbs the first time I had the floats bent to far not I got them measured out the boat won't even start. Any suggestions?
@sqzbox56
@sqzbox56 10 ай бұрын
Brandon, When I went to your site to buy a Carb Float Gage, my computer gave me a warning saying that the site was a potential security risk. Is there any other way I can still buy one of your gages without risking bringing harm to my computer? Thank You.
@BrandonsGarage
@BrandonsGarage 10 ай бұрын
It's saying that because I didn't buy a SSL certificate; as I don't handle the credit card processing, or payment at all (PayPal does), this would have been a waste. I can't get more secure than paypal.
@daynelindquist4696
@daynelindquist4696 4 жыл бұрын
I have a 1979 100hp johnson javelin. It runs pretty bad at low speeds on a load but really good at fast speeds on a load. How can i make it run better at low speeds?
@unsaltedlife5998
@unsaltedlife5998 2 жыл бұрын
Did they use straight 30 weight oil for 2 stroke outboards back then?
@BrandonsGarage
@BrandonsGarage 2 жыл бұрын
Not in 78, but in the 50's they sure did.
@ManuelHernandez-eu5jp
@ManuelHernandez-eu5jp 7 жыл бұрын
Awesome channel!!!....I recently bought a 1966 Rivers with an 80hp Johnson Seahorse previous owner said just needed to be fined tuned. I really don't know anything about boats but couldn't pass up the deal was wondering if you've worked on this type of motor before?
@BrandonsGarage
@BrandonsGarage 7 жыл бұрын
What year is the engine?
@ManuelHernandez-eu5jp
@ManuelHernandez-eu5jp 7 жыл бұрын
I believe it's a 1966 as well not sure. The Model Number is V4SL-18C if that helps
@BrandonsGarage
@BrandonsGarage 7 жыл бұрын
1966 80 Hp. I'm not that familiar with them - but you should be able to get a manual pretty cheap. But, you might want to look into a newer motor with more available parts.
@ManuelHernandez-eu5jp
@ManuelHernandez-eu5jp 7 жыл бұрын
I will look into it. Any suggestions on what I could replace it with? Appreciate your help
@BrandonsGarage
@BrandonsGarage 7 жыл бұрын
Any newer evinrude / johnson. I would try to go 80's and newer. Seems they mastered them by 1980.
@sirjustis
@sirjustis 4 жыл бұрын
You are doing such a great job with the content! Quick question: did you do a follow video of this motor?
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
I have the install and test run footage, but its horrible quality.
@thomasflynn642
@thomasflynn642 7 жыл бұрын
my carbs are flooding? what is the float settings asap thanks
@fdyhdfhy
@fdyhdfhy 6 жыл бұрын
Thomas Flynn he says it in the video. 31.3/2.
@williamriley2528
@williamriley2528 4 жыл бұрын
Hey those old stories you heard about carb cleaner were totally true... A little 175 psi compressed air works wonders... It's called a "needle & seat"... Do you really wanna run ethanol in your boat engine...? They are called Corbin clamps...and Corbin clam pliers... Just spray the gaskets with Permatex copper coat...
@j.inlighten4020
@j.inlighten4020 3 жыл бұрын
What measurement did you set your float at?, I'm rebuilding 2 of the same carburetors..both of my floats were different lengths..
@BrandonsGarage
@BrandonsGarage 3 жыл бұрын
I have a float gauge I use
@j.inlighten4020
@j.inlighten4020 3 жыл бұрын
@@BrandonsGarage ..I can't find the specs for it?..the length anywhere?
@TheRIFLEMAN243
@TheRIFLEMAN243 Жыл бұрын
Have you ever had any luck with cheap aftermarket carb kits for this motor?
@BrandonsGarage
@BrandonsGarage Жыл бұрын
Eh, floats kind of suck as does the bowl gasket. I mean, they work, but how well/long.
@javiermontes3777
@javiermontes3777 Жыл бұрын
I got the same carburetors where I can buy the gaskets
@jasonkinley2243
@jasonkinley2243 5 жыл бұрын
Hey Brandon . Where do I find the plastic piece on the end of the choke solenoid? I've looked all over the place, whats the actual part called?
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
Depends on the year/HP, but this one is: 0322405 - CLEVIS, Plunger to lever
@jasonkinley2243
@jasonkinley2243 5 жыл бұрын
That is it . It's a 78 115. Thanks man !!
@jasonkinley2243
@jasonkinley2243 4 жыл бұрын
You got one laying around ? I can’t find one anywhere
@donavinalbright1544
@donavinalbright1544 11 күн бұрын
That choke linage where it connects I can’t find anywhere anyone got any suggestions
@jeffhayhurst9538
@jeffhayhurst9538 6 жыл бұрын
Do you know what part numbers the rebuild kit was. Have exact motor and fuel line and carbs all clogged. Also where did you order from if you remember. Thanks Shop wanted over $650 to do the work.
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
its in the description. Well, click the link then it is. And yeah, thats too much, thats why we do it ourselves!
@fdyhdfhy
@fdyhdfhy 6 жыл бұрын
When you took apart the first carb there was no hanger for your float pin. You replaced it WITH the hanger. Does this matter? Mine is bogging and I’m thinking it’s becuase the pin is getting stuck becuase it doesn’t have a hanger. Could I be correct? Was this why you put a hanger in???
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
So, Years ago I had a 1984 Honda ATC 200x. The float worked, but the needle got stuck up there all the time. When the thing wouldn't start, or would start, then die after using the gas in the float bowl, I would find a rock and tap on the carb, then I was good to go! Years later, I was helping a friend move some stuff around a yard, and there was a Ford 9N tractor there for us to use, which didn't run because of a carburetor problem. Once again a rock was used to remedy this. So, do I believe that happens, YES! New kits come with the little arm to pull the needle down and I love it. Keep in mind, the engines I reference were gravity fed. Out motors use a fuel pump, and thus have pressure to push the float down. If you're ever stuck somewhere, you would be surprised how handy a rock is. A rock is just natures hammer.
@ronaldstover636
@ronaldstover636 3 жыл бұрын
is there any way to adjust these carbs to get them to idle??
@ghoff2
@ghoff2 3 жыл бұрын
Adjust your idle screw
@jatoav8or
@jatoav8or 4 жыл бұрын
Should have done the welch plugs just to show folks how easy they are. There’s been many a time I’ve found debris caught up in the little chamber.
@dougfleming8816
@dougfleming8816 2 жыл бұрын
How do you reseal the new plugs?
@jatoav8or
@jatoav8or 2 жыл бұрын
@@dougfleming8816 Most carburetor kits have the new plugs and you just put them in place where the old one was in tap them in with a soft metal or wood punch. When you said it in place it’s convex like a little button and then when you tap it down in the middle it’s concave and it seals tight metal to metal. I’ve been extremely sick with Covid and not able to reply to anything for sometime so sorry for the delay
@simonelizondo3080
@simonelizondo3080 6 жыл бұрын
Do you know what the float adjustment is on the carb? I’m rebuilding mine. Do we even need it?
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
Its pretty important, get it as close as possible,
@johnpalmucci6351
@johnpalmucci6351 6 жыл бұрын
Brandon's Garage l
@harrymhill
@harrymhill 4 жыл бұрын
Where did you get the rebuild kit?
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
Amazon probably, maybe ebay. here is a reference chart: everythingoutboards.com/brp/carbkit/index.html
@chase9390
@chase9390 4 жыл бұрын
We’re do you order your parts for this motor?
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
I believe these were from boats.net
@chase9390
@chase9390 4 жыл бұрын
Brandon's Garage hey I was curious if you could help with som wiring questions I need to know what color wire does goin to the ignition switch. Rats chewed up the wires pretty good. It has a dash mounted ignition switch
@trevorhanlon471
@trevorhanlon471 7 жыл бұрын
HI Brandon great informative videos,here in oz we have a fellow youtuber (DANGAR MARINE) . You guys help so much : ) Thanks
@thomasflynn642
@thomasflynn642 7 жыл бұрын
hey, gas comes out if the hole in the middle of the top carb? why is that ? i set the float height to specs! RESPOND ASAP
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
Was the engine level, or tilted up a bit?
@ct1762
@ct1762 5 жыл бұрын
that carb cleaner is nasty stuff. i recommend a cheap ultrasonic cleaner with simple green HD (not regular as it can be corrosive). cleans the carb in 20-30 minutes way better than just a soak, and you won't risk getting lymphoma lol.
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
Naw, Thats California CARB friendly. Its similar to colored water.
@ct1762
@ct1762 5 жыл бұрын
@@BrandonsGarage Oh...i always thought it was super toxic. Good to know!
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
Well, talking to old timers they would say the carburetor would get clean when it came in contact with the fumes from the 'old stuff'. You dare not let it soak. Even the factory manuals mention this. This modern junk, naw.
@ct1762
@ct1762 5 жыл бұрын
@@BrandonsGarage Yea i'm sure some of that stuff was bad. I guess they way the factory wants you to do it is with alcohol and a syringe. never tried that either.
@Ralphecy
@Ralphecy 2 жыл бұрын
never stick a wire in any carb you can scratch the internal walls of the gas or air
@Ralphecy
@Ralphecy 2 жыл бұрын
canals and change flow Use a strong Rubber tipped Air gun nozzle to blow out small canals in the carb .
@fredhuang9223
@fredhuang9223 Жыл бұрын
Bottom carb..
1978 Evinrude 85 HP Lower Unit Service - Fluid and Pump
30:36
Brandon's Garage
Рет қаралды 183 М.
1988 Johnson 90 HP; Carbs, Fuel Lines; VRO Delete
46:36
Brandon's Garage
Рет қаралды 84 М.
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
Top 5 Most Common Carburetor Problems & How To Fix Them
6:05
Rocky Mountain ATV MC
Рет қаралды 206 М.
How to Rebuild a Evinrude Carburetor Step by Step
19:31
Om Fishing
Рет қаралды 205 М.
Classic Car Survival - Troubleshooting Carbureted Engine Fuel Delivery Systems
21:07
1985 Evinrude E150STLC0S Carburetor clean & rebuild.
16:54
Robert Stephens
Рет қаралды 3,4 М.
1977 Evinrude 115 HP - Fuel and Ignition Issues
19:55
Brandon's Garage
Рет қаралды 3,6 М.
60 HP Johnson VRO Evinrude Carburator Rebuild
29:00
Ralph Pierre
Рет қаралды 207 М.
9 Symptoms of Bad fuel Injector; How to Diagnose and Clean?
9:30
haile auto garage
Рет қаралды 552 М.
Awakening a 90 HP Johnson After a 12+ Year Slumber
19:43
Brandon's Garage
Рет қаралды 189 М.
Evinrude 85hp wont idle
2:25
ElGlenbob-O Loco
Рет қаралды 6 М.
Johnson / Evinrude carburettor service
18:32
Dangar Marine
Рет қаралды 584 М.