Bravo One Outdrive Service - Remove Gimbal Bearing

  Рет қаралды 144,148

jcook007fix

jcook007fix

Күн бұрын

Пікірлер: 58
@gd9704
@gd9704 11 жыл бұрын
Love REAL WORLD videos of repairs....it never goes easy! Great job figuring out how to get it done and not giving up!
@milkman44107
@milkman44107 8 жыл бұрын
Thank you commander! This video and music inspired me to do the work myself! I hooked up my laptop to my boombox and blasted the music as I did the work! It provided great motivation!
@WhoeGivesAFunk
@WhoeGivesAFunk 6 жыл бұрын
I'll give you pleasure! LOL. Working on removing my gimbal bearing now. Time to go back outside and keep pulling at it! Thanks for the video.
@grantsans4775
@grantsans4775 10 жыл бұрын
Funky music aside thank you for a very informative video. Somethings locking rotation on my 3.7L Alpha One (Engine, Gimbal or U-Joints). Learned more about the gimbal bearing and good tricks to remove it.
@VR-fn3kv
@VR-fn3kv 4 жыл бұрын
You are as determined as a Tasmanian devil. The stuff you were trying reminds me of myself. I was laughing at myself watching you. For $45 it's easier to buy a gimbal bearing puller.
@paradisemace1
@paradisemace1 9 жыл бұрын
If the slide hammer fails, run a two foot piece of all-thread through the puller and spreader with nuts on either side to spread the puller. Grab the bearing then slide a piece of metal with a hole in it over the all-thred. Chase that with a nut and tighten until bearing is pulled free. Good luck
@knowyuhgrow420
@knowyuhgrow420 3 жыл бұрын
Thanks for sharing 👍🏽
@bonvivant55
@bonvivant55 11 жыл бұрын
Please give the rights to someone, that music is epic
@jkdwayne
@jkdwayne 11 жыл бұрын
Easy Way.... Drill about 3, 1/4 diameter holes in the aluminum ring. It Relieves the press fit and the bearings fall right out.
@s9bryant
@s9bryant 11 жыл бұрын
Great video! But I must have missed something. The foot on the puller pulls the bearing out, but how do you get the carrier out?
@lmllosa
@lmllosa 8 жыл бұрын
Great video..! I'm having exactly the same problem, I drilled holes on the carrier but didn't work. I can't turn the bearing, which kind of blade did you used to make the knoch?. I bought the gimbal bearing puller, I rented hammer with the pullers... simply doesn't move a bit..
@lloydcisco3027
@lloydcisco3027 7 жыл бұрын
I did get some good out of this video. I taped the music so I could blast it for my liberal. Nabors to piss them off worked great! Thanks for sharing.
@chrismadaj8751
@chrismadaj8751 2 жыл бұрын
But they will never understand it
@oddev
@oddev 11 жыл бұрын
What's up with the music?
@wolfhawg
@wolfhawg 5 жыл бұрын
Great high stress music.
@ccccen
@ccccen 11 жыл бұрын
can the alignment be done without removing the sterndrive? I just had a new drive put in and afterward the mechanic told it was out of alignment, should he had made sure it was aligned before putting in the sterndrive?
@Criticalyconcernedregular
@Criticalyconcernedregular 3 жыл бұрын
Here it is 2021 and this is an epic video and I died laughing at all the comments and I personally thought the muzak was appropriate for the sH!+ Job that it is to do this service.. hope everyone is still alive in well as we dive into tyranny and medical overbearing government over reach! Also let’s go Brandon!
@Autobotsunited
@Autobotsunited 2 жыл бұрын
Lol amazing comment.
@jcook007fix
@jcook007fix 11 жыл бұрын
Well, the carrier comes out with the bearing. The outside dia of the bearing is convex and the inside dia of the carrier is concave |))| . This creates the gimbal movement of the Gimbal Bearing.
@laundert
@laundert 12 жыл бұрын
How often do you have to change that bearing?
@habit681
@habit681 11 жыл бұрын
great info but why put the most annoying music ever in the background. why did you even put music in......its not MTV!
@brianswimmer23
@brianswimmer23 12 жыл бұрын
thanks for the info!
@ryanlas54405
@ryanlas54405 7 жыл бұрын
had to mute this.. the music is awful... way to loud. drowns out the voice.
@kbgking7921
@kbgking7921 3 жыл бұрын
Sorry the music killed it for me!!! Only could handle 30 seconds
@RobbyWorld1
@RobbyWorld1 10 жыл бұрын
Ok, after watching it again it's a great how-to video, but I'd still like the music turned down or the voice turned up. Good music, just too loud. And I see it's original. Impressive. A+ overall. (no luck yet with my #$%^@&^ gimbal bearing. Need that bigger slide hammer ;-) )
@jcook007fix
@jcook007fix 10 жыл бұрын
Sorry for the loud music.
@goodboyringo9716
@goodboyringo9716 9 жыл бұрын
Why had music while showing an informative video?
@andyc3020
@andyc3020 12 жыл бұрын
Great video but either lose the music or turn it way down. Thanks
@eorchestrator
@eorchestrator 12 жыл бұрын
Nice job.
@lloydcisco3027
@lloydcisco3027 7 жыл бұрын
Turn that music. If that's what u call it off.
@MortuMoturi
@MortuMoturi 11 жыл бұрын
Well, if your wife would have help you, it would have been alot quicker! Great job!
@raulduke7142
@raulduke7142 2 жыл бұрын
PITA. Nice job. Whhwwew
@waterwater2193
@waterwater2193 3 жыл бұрын
Had to turn the volume down
@jairperez8565
@jairperez8565 8 жыл бұрын
good good good thank you
@guglielmodicarlo4139
@guglielmodicarlo4139 3 жыл бұрын
love your vids,, but brother loose the music
@goodboyringo9716
@goodboyringo9716 9 жыл бұрын
Why have , not had
@jcook007fix
@jcook007fix 9 жыл бұрын
R Shay Get more free help at www.bravoone.slantpower.com
@stuartadair
@stuartadair 5 жыл бұрын
Watched half way through then couldn't stand the music anymore
@keithmalatesta7660
@keithmalatesta7660 9 жыл бұрын
good video... turn the music down.
@UrbanCheese709
@UrbanCheese709 6 жыл бұрын
Oh my god. Why did you think you needed the dreadful music?
@fishheds
@fishheds 6 жыл бұрын
Music gave me PTSD. Thanks, Obama.
@markjennings2315
@markjennings2315 5 жыл бұрын
I couldn't bear that musak
@Bymb2020
@Bymb2020 11 жыл бұрын
I think someone bought there puller from harbor freight lol
@RobbyWorld1
@RobbyWorld1 10 жыл бұрын
No need for music in a how-to video.
@joelopez4758
@joelopez4758 7 жыл бұрын
Why do people ruin a good video with horribly distracting music? Had to look for another video...couldn't take it anymore.
@kennsaunders1690
@kennsaunders1690 5 жыл бұрын
Music is annoying.
@artmolina
@artmolina 7 жыл бұрын
Dude! The fucking music!!! Had to stop watching, annoying.
@gary1984g
@gary1984g 3 ай бұрын
Background music is unnecessary and annoying
@kingtut5923
@kingtut5923 4 жыл бұрын
What's with the fucken music
@chrisdiebold9368
@chrisdiebold9368 3 жыл бұрын
That background music sucks
@BerryMcCaulkiner859
@BerryMcCaulkiner859 4 жыл бұрын
That music is fucking horrible
@skidooboy332
@skidooboy332 12 жыл бұрын
gay song
Bravo One Outdrive Service - Drive Shaft Seal
12:46
jcook007fix
Рет қаралды 87 М.
How to Remove Stubborn Gimbal Bearings (Without Breaking Your Boat)
7:52
Moccasin Marine LLC
Рет қаралды 2,7 М.
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 14 МЛН
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 16 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 53 МЛН
Support each other🤝
00:31
ISSEI / いっせい
Рет қаралды 44 МЛН
Removing a mercruiser bravo u joint bellows and gimbal bearing
11:27
Purpose of your outdrive gimbal bearing - How it works
11:29
DIY with Michael Borders
Рет қаралды 7 М.
Remove Mercruiser alpha / bravo outdrive gimbal bearing - DIY
13:33
DIY with Michael Borders
Рет қаралды 19 М.
Bravo One Outdrive Service - Install
11:23
jcook007fix
Рет қаралды 121 М.
Exhaust Bellows in minutes with this home made tool!
7:23
PM-Performance
Рет қаралды 33 М.
Bravo III Gimbal Bearing / Oil Seal Removal
2:31
Outdoorsman Channel
Рет қаралды 14 М.
Replace Mercruiser alpha gimbal bearing grease seal
12:53
DIY with Michael Borders
Рет қаралды 8 М.
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 14 МЛН