If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. Clamp set: amzn.to/45UKgnS Removal/alignment tool: amzn.to/455xUbm Exhaust bellow install tool: amzn.to/3EKIQQG Bellows replacement kit: amzn.to/3RL7h8v Outdrive gasket kit: amzn.to/3rb5HBR ************** 1. Replace Mercruiser alpha one gen 1(2) bellows - PART 1 kzbin.info/www/bejne/hJSyk4eFjr2nh68 😎👍
@davestewart9146 Жыл бұрын
It’s all in the right tools, I really like the hose clamp tip, thanks Michael 👍😁
@DIYwithMichaelBorders Жыл бұрын
So true, having the right tools makes or breaks the forward motion of a DIY project. Thanks Dave. ☕️
@mlbowdish123 Жыл бұрын
Nice work Mike!
@DIYwithMichaelBorders Жыл бұрын
Thank you, many more to follow. 👍
@markbailey60519 ай бұрын
Notice that the barring comes with the barring carrier. The barring carrier is designed to stay in place and the barring is designed to pivot 90 degrees and slid out of the carrier slots. If you are lucky enough to have the carrier installed by the guy before you with the slots facing aft, then just buy the barring and leave the carrier alone. If the barring comes with the carrier, remove the barring from the carrier and install in your existing carrier. The carrier allows the barring to pivot, this allows the drive shaft the ability to align properly. If you are replacing the barring You should be replacing the billows.
@DIYwithMichaelBorders9 ай бұрын
Thanks for watching and sharing your thoughts, always welcome here. Very nicely explained and below is a link to our video explaining the design and purpose of the gimbal bearing. kzbin.info/www/bejne/b53He56XqbR_bZosi=Vn0EMwyICIErBwTO You get to see us moving the bearing all around in its race. Engineering at its finest. 👍🧰
@independentthinker8930Ай бұрын
The gimble bearing I replaced had radius outer race, tilt and came out through 2 notches
@DIYwithMichaelBordersАй бұрын
@@independentthinker8930 Thanks for watching and sharing this. How’s your DIY project going along? 🧰
@independentthinker8930Ай бұрын
@@DIYwithMichaelBorders going good, when I get parts, trickling in
@DIYwithMichaelBordersАй бұрын
@@independentthinker8930 Very cool, that’s exciting. We know that feeling all to well as we patiently wait for our parts to arrive. 👍
@njsford4life2 ай бұрын
Need help diagnosing. Have a mercruiser alpha one gen 1. Gave it some throttle and it felt like it was dragging. Low power. Almost like a car with a slipping transmission. Any advice is that appreciated!
@PBinns22 ай бұрын
Sounds like a bad drive coupler. I've never had one myself but am told it will often smell like burning rubber in the engine bay.
@njsford4life2 ай бұрын
@@PBinns2 turned out to be the carburetor
@inthenameofmyfather38365 ай бұрын
should the new gimbal bearing be tight so that you cant turn it with your fingers after install? thanks
@DIYwithMichaelBorders5 ай бұрын
Thanks for watching, it should be tough to move or rotate after install. 👍
@PaulDudek2 ай бұрын
I am doing the same project on a 4.3 1989 GEN, one alpha one and I can’t find the serial number to get the exact maintenance manual for all the right part numbers that I’m gonna need any ideas?
@DIYwithMichaelBorders2 ай бұрын
@@PaulDudek Thanks for watching, any update? The serial number can also be found on a sticker or placard placed on the inboard engine. Worst case scenario, you will have to remove a decal or two from the outdrive where you will find serial number. If that ends up being what you have to do, we have attached a video below that shows us installing brand new decals to our outdrive. 1. Remove and install new decals. kzbin.info/www/bejne/e4OYY2iwdt1kebssi=1xOC-hJZCw2t9w30 2. Punching serial number into new decals. kzbin.info/www/bejne/pXrVhoipfcp7bNksi=kg-KT6xTluADxKbb 😁👍🧰
@shawn_hu Жыл бұрын
is this gimble bearing supoose to be service free?
@DIYwithMichaelBorders Жыл бұрын
Good morning, that’s the design indeed. The newly designed sealed bearing will not require routine maintenance/greasing.
@davidjessee77013 ай бұрын
Or you could get a 3 jaw puller and a slide hammer and pull the old gimble bearing out.. then use the correct bearing driver and a hammer and drive the new bearing in till it bottoms out! No need to mark … make sure you align the grease hole on the bearing with the grease fitting to grease the gimbal bearing.. if not it will not accept grease from the zirk fitting
@DIYwithMichaelBorders3 ай бұрын
@@davidjessee7701 Thanks for watching and sharing your thoughts. 😁👍🧰
@DIYwithMichaelBordersАй бұрын
@@randycraft3166 👍
@Mbrown5534 ай бұрын
Was your bearing hard to.spin after replacing it?
@DIYwithMichaelBorders4 ай бұрын
Thanks for watching, it will be a bit tough to spin by hand however not too tough. Once bearing is installed into cavity/bore, it adds a tiny level of compression to carrier however shouldn’t impede on the operation of bearing. We have added a video discussing more about the gimbal bearing. You may find it helpful, you may not. kzbin.info/www/bejne/b53He56XqbR_bZosi=3ndhplOoSCqU_ooq Keep us posted with your DIY project.
@Mbrown5534 ай бұрын
@DIYwithMichaelBorders okay that's what I figured. I put the shift in it and it spins freely. The motor goes back in tomorrow. I replaced the old locked up motor with a reman 3.0L and the lower unit due to a cracked case. Upper unit was in good shape. I only decided to do the gimbal bearing to get a sealed unit in there to avoid worrying about keeping the greased older unit full of grease. Thanks again for the attention to detail. P.s I found a copy of the service manual online for free somehow.
@DIYwithMichaelBorders4 ай бұрын
@@Mbrown553 That’s awesome, sounds like you’ve been busy. Great idea replacing gimbal bearing, adds peace-of-mind knowing you have a brand new bearing.