I watched both part 1 & 2 to the end and I don't even need to change a water pump right now, but I own two of these Ecotec's. I appreciate the detail, tips and humor, and I know how much work it takes to edit, "render", upload, publish, etc. Thanks
@mikeh35592 жыл бұрын
the video work is a pain in the rear.
@TheCrazycray4 жыл бұрын
I watched until the end I'm about to attempt on my sister Malibu your a life saver they want to charge her 600$ for this job now it will cost her only parts!!!! I'm totally subscribing
@rommelges11 ай бұрын
Truly appreciate the time and effort show us the job, I’m pretty good at basic car repair, but this one’s got me on the fence.
@jayssimplelife45544 жыл бұрын
Great video did whole repair about 2 hours keep everything organized and work slow I’m not even a mechanic and job was completed if I can do it you can do it trust me good luck everyone
@hizkie82383 жыл бұрын
I'm working with a 2012 chevy malibu and there is a hidden bolt behind the water pump near the exhaust, how do I remove that?
@loganwork70247 ай бұрын
@hizkie8238 I know I'm too late, but maybe it will help someone. Service manual says to remove exhaust manifold, but you dont have to. I got a 1/4" flex head ratchet with a short 10mm in from under the car. There isn't much room to turn it out by ratchet, I had to put the socket on and use my hand. I also have the fender cover and oil pan off, so that might have helped me. Good luck!
@MikefngarageАй бұрын
buy the tool that covers the whole thing. Copy of the dealer tool. Ebay 10 bucks.
@edwardcruz74711 ай бұрын
Awesome job explaining all the steps. Never done this before and got the job done thanks to you. I will add I did drop a bolt in the crank and thankfully was able to get out fishing blind with a magnetic. Thanks again for the video.
@woodyglendell74004 жыл бұрын
What have I learned from this well done video? That there's no way my arthritic hands, fingers and wrists are gonna make it. It will be sent to someone like you, Sir! Thank you.
@006Painkiller4 жыл бұрын
I have 0 mechanical knowledge but gonna replace my water pump later today thanks to your videos. Hopefully everything works out good
@bluesriot24 жыл бұрын
how did u make out ?
@joelopez11712 жыл бұрын
I failed to mention the excellent quality of this video, thank you. I will have to take it to the dealership
@Mayamax35 жыл бұрын
I watched all the way to the end. Couldn't resist my morbid curiosity to view a truly nightmarish water pump repair. The lack of access & limited visibility makes that repair a royal pain. Thanks for sharing the experience.
@briansmobile15 жыл бұрын
The beauty of this video is that any of the unknowns or hidden things that could trip you up are blown wide open. If you understand the concept and know what you'll need and what to do- it's not a big deal anymore.
@Mayamax35 жыл бұрын
@@briansmobile1 I've tackled many a repair in my day, but I'd gladly pay you to take care of this one for me. No substitute for experience.
@bruceyounger59083 жыл бұрын
Generally I am not afraid to tackle a repair unless we get into pulling engines or something. Also, I am not a pro, I am a mechanic out of necessity! My son has a 2010 Cobalt and it appears that the water pump has failed. I have spent a lot of time researching the replacement of the the pump and to be honest it has me a little frightened. To this point, your two-part video is calming my fears. Thank you for taking the time to explain the details and especially the magnet to bolt tip. If anyone is going to drop a bolt into a timing casing, it's going to be me! So Thank You for that, I am ordering the magnet tool in the link right now!!!
@dave11355 жыл бұрын
I watched to the end, and loved the man's prayer at the end from red green
@blk95gsrt4 жыл бұрын
Hey Brian, when I do these I take a 6x1.0 bolt and cut the head off of it and thread it into the drive pulley on the pump, that way I have a stud to line it up with the gear.. then you don't have to fight it trying to line up the bolt holes from the gear to the pump. Also, instead of trying to use a magnet held against your socket take a tiny piece of paper and set it in the side of your socket and push the bolt in, the paper will cause a tight enough fit to hold your bolt in the socket and then you can thread the bolts in that way. Hope that helps.
@pdaddy879 Жыл бұрын
Excellent tip
@maustank88645 жыл бұрын
Great video. I’ll be getting rid of my Malibu this week lol!
@MyProductTutorials4 жыл бұрын
Just bought a Malibu with a leaking water pump and here I am lmao
@RamenRanger3133 жыл бұрын
I got a Terrain that just smoked the WP. FML
@ThomasJohnson.2 жыл бұрын
😂😂😂😂❌🧢
@johnjacob99762 жыл бұрын
Lmao
@meganhendrickson15963 жыл бұрын
Thank you very much even though this took me two days with a two year old I managed to get the job done.... the right way.... 100%
@mt18855 жыл бұрын
WATCHED to the END great video !!!
@TG-be3io4 жыл бұрын
Just got into one on an equinox tonight after watching this video. One big set back that I came across that you dont have to worry about is the engine block heater goes directly behind the water pump! And its really in the way! Also seems to be alot less room around the 2.4 in the equinox. So far not a bad job if i can avoid pulling the exhaust manifold. Thanks for the tips. Sure makes it a hell of alot easier!
@982Nighthawk13375 жыл бұрын
I'm not doing this job but I'll watch just about any video you put out. Thanks for putting out quality content.
@Scout4Truth3 жыл бұрын
Love the scrapyard moment at the end, worked at a yard for a while and it was full of fun times like that. I have seen pickups break in half from rust, the other yard worker took the fork and ripped the cab off the frame since it was all scrap so we could get to the engine
@bomarc88593 жыл бұрын
Great video. Yes. I watch the video to the very end and I appreciate the detail. the quality and the time it takes to make such a good video. thank you.
@markmartinez37803 жыл бұрын
I don't think your video was missing anything or was too long. Thanks! Lisle FTW
@phantomhowl123 күн бұрын
This took me 3 days to complete. Mostly because I'm a goober and procrastinated. Your video made this a whole lost easier. I haven't turned it on yet. So I've yet to find out if it's gonna whine or not.
@iamPhZ2 жыл бұрын
Got it done!!!! ✅ THANK YOU for both your videos! This saved us from the stress and spending money for the water pump replacement job. I did end up with a whine at the end BUT, I’m sure it’s because I tightened the water pump sprocket bolts too tight. Going to SLIGHTLY loosen them. Wish me luck!
@jeffedwards20452 жыл бұрын
Did that work?
@benjarvis54072 жыл бұрын
Thanks so much for posting this up. It's really helped me out a lot. Currently halfway through doing this on my 2007 Alfa Romeo 159 2.2JTS Selespeed with a squealing water pump bearing @ 260,000kms
@frankregan90163 ай бұрын
Thanks for taking the time to make these vids brother
@spankey00695 жыл бұрын
Great videos as always. I watch to the end, but I don't always watch the bonus footage...BUT I usually skip to the end to give you credit for the whole vid.
@daniellebowman77244 жыл бұрын
Took me 2 days to complete this job because I dropped a bolt in the timing cover. Took the oil pan off wasn't in there so finished taking out the water pump where I was able to fish it out with a magnet. I consider myself mechanically inclined but this is by far the hardest job I've ever done and ive replaced whole engines and transmissions. If anyone on here is thinking about buying a Malibu or equinox with the 2.4 don't do it and if you do take it to someone else to be serviced. They'll hate it too but it will save you the headache.
@biff2k2 Жыл бұрын
I’m replacing my timing and balancer Chain and the kit has a water pump so this should be fun.
@City_BusDriver Жыл бұрын
Where did you fill the car up with coolant? Was it threw the reservoir?
@moegamezzz3622 Жыл бұрын
@City_BusDriver yes it's through the expansion tank
@craigjorgensen46373 ай бұрын
Some shops will quote sky high prices to do a job like this! They actually hope the customer will take the job elsewhere. If the customer decides to stay with them then they make a lot of money still taking the risks of a miserable job! I really can’t blame them. Anytime a shop takes on a miserable job that is time intensive they likely have to turn away other more profitable jobs!
@paullindsley80812 ай бұрын
I’m doing it right now, spend 4 years doing transmissions and engines etc. this is the hardest job I came across as well
@richardcrouse46442 жыл бұрын
Watched both parts to the end!! Thanks for the education.
@wyelandlebeouf72024 жыл бұрын
Great video parts 1 and 2 thanks to your knowledge and telling me about that special g.m. timing tool I got grandpas new waterpump in for a fraction of what anyone would've done it for. Sucked putting the new one in I ended up having to pass it from the under driver side over the exhaust over the frame then stuck it in from the bottom. Guess theres a 1000 ways to skin a pig! Thanks my guy!
@gfildirt5 жыл бұрын
Nice video. I did this on a vue and dropped the bolt. Took 20 minutes to fish around with a magnet to finally get it out.
@cka17995 жыл бұрын
Funny you posted this today. I just finish a timing chain and water pump on a 2.2l ecotech this afternoon. I think I like working on my 2.5I better, but I have to say the timing was super simple. The chain really stick in the teeth compared to a belt. Oh I love your tips and Bonus footage, so I watch till the end
@benmccallie1214 жыл бұрын
I'm gonna go for it tomorrow thanks for the video
@milanwaggoner3632 жыл бұрын
Watched both parts to the end. Thank you
@droppindeuces69815 жыл бұрын
As always Brian, great video. There is a lot to that H2O pump! Where ever you feel the extra (put back together) instruction is needed, it probably is. Personally I can use all the help I can get. Thanks for all the work you put into your content!
@kitjasabsgabs183014 күн бұрын
It's retarded. I showed the lady my car, 07 town car. See the alternator? Under that is water pump. A handful of bolts, and fill with coolant and put 2 alternator bolts back in and I'm done in 30 min flat. Your Malibu takes me 30 min just to get the damn tool like this blue 1 in cause not enuff room, right beside the front support, can't jack up engine for the way it's made. It's Insanity. Only worse 1 was 3.5 ecoboost. 10.5 hours, and while I'm there it had Ober 100k, Ford says do timing set while there. I don't think I'll ever do another ecoboost unless it's mine. No more GM like this. Wtf GM???
@davidsoncortlandt295924 күн бұрын
Great job great explanation. Watched both videos from beginning to end. It worked out well for me and I'm glad I didn't take it to the shop.
@AntonioClaudioMichael5 жыл бұрын
The extra footage is always great to watch bro
@RayRay-ov7uw5 жыл бұрын
Love the Red Green show as well and I watch all your videos to the end
@jgrm44432 жыл бұрын
31 December 2021, I watched both part 1 & 2 to the end. Thanks for sharing. Help me a lot. Good Job
@briansmobile12 жыл бұрын
Awesome, thank you!
@dustinpetrey81484 жыл бұрын
So glad I watched this video before doing it I watched another video he didn’t use the tool and took timing cover off
@robertnovotny45883 жыл бұрын
Entertainment video on your descent job , great video Brian.
@michaeltyniec70103 жыл бұрын
Loved your Man's Prayer (Red Green) at the end - so yes I watched to the end. Great video - I've got a Buick Verano that will need this soon.
@patrickknox46182 жыл бұрын
Thank you for your time into this and probably all your vids!! that helped soo much, now i know i can do it. im just a shade tree mechanic i prefer to rebuild an engine on a stand because leaning over the hood kills my back as i am fused . thanks again.
@d.j.99613 жыл бұрын
Hey Brian, Could have sworn that I was subscribed to you, a few years ago, I could have sworn!!!! Anyways, I hit the sub button AGAIN! I purchased a 07 G5 2.2 vin-F & lucky me, This car has every problem a G5 can have & some!!! It was running when I approached at the lot so, The tapping at start up was hidden from me! When I realized the issue, I rushed & ordered a timing tensioner & THANK GOD I HAD MY LITTLE EXTENDABLE, ANTENNA STYLE MAGNET WITHIN REACH Because, As I unscrewed the 32mm socket, IT ALL CAME APART INTO PIECES & Thankfully I had the magnet ready! I just ordered a dr.engine timing set $124.88-133.93 after tax, from ebay! It comes with a new oil pump/front engine cover, water pump, both timing chains, 3 tensioners, oiler, & all the guides, 2 cam gears, 8 bolts(new cam bolts, & guide bolts, along with a front engine cover gasket. My water pump works fine so, I am debating on whether to change it & the biggest thing is, My cooling fan DOES NOT WORK PROPERLY ON ITS OWN! I extended all my know how & don't know how to fix it but, when I probed one of the pegs in the fuse box for the cooling fan relay, (test light attached to ground) When I touched 1 peg, the fan came on! I went to the junk yard & got another relay & that did not help! So, I connected to that peg in the fuse panel, ran to a toggle inside the car & then to ground so, When I hit the toggle, the fan comes on! The temp usually bounces between 183-189 but, If I am stuck in traffic or going up a massive hill at low speed, I have seen 210-212 degree-SCARY!!!! The fan spins when I activate it but, I am a loss as to why it does not function properly? So, I am scared to open up the cooling system & risk any air bubble's! I do not have a cooling system vacuum tool or any fancy cooling system tools! besides a squeeze clamp tool.. anyways, I worry about summer time temps & just how to get my cooling system working properly but, I ordered a timing kit & soon, I will be installing it & getting to the root of the tapping noise at start up!!! Any suggestions on my cooling fan issue? it has a single fan yet, the fuse box has relays for cooling fan 1, & 2 with a 3rd spot for a fuse. The car had some front end damage in the past & i don't know if this fan is the correct fan or not? I also purchased a new crank bolt, & the two 0-rings for the coolant tube (90537379). Still need dexcool! Gasket maker & maybe a new thermostat gasket? Will a small sqeeze tube of gasket maker be enough for the timing job or do I need a full tube that fits into my caulking gun?
@onsab123 Жыл бұрын
Great video. This is a job in dreading. Thank you for the tutorial!
@dybukk4 жыл бұрын
FYI - The best way to line things up when reinstalling is to install an M6 threaded rod (about 50mm) into one of the screw holes. Helpful when installing those things blind when you have the full circle holding tool.
@salvadorsalcedo8733 жыл бұрын
Ok, this is the easy way ? How will be the difficult way....
@TheNobleLoyalist Жыл бұрын
Ryan, I'm about to change water pump and thermostat on my 06 pontiac solstice 2.4L manual (fhe 2.4 is the non turbo base model but my car has a Hahns Turbo and Intercooler, with custom tune, and obviously original air box and air filter removed and replaced with an open conical filter attached to a long tube running from the intake obviously, and sits dead center over the fan shroud/between the turbo charge pipes. Not sure why I just told you that as it has nothing to do with my reason for commenting LOL My question to you is could you explain this rod method you stated? Thank you
@virgiliob35723 жыл бұрын
It's that Pittsburgh Mini Pick I love those tools 🔧 I like the video by the way thanks for your help brotha.
@joebradshaw92263 жыл бұрын
Thank you. going to do the water pump on my wife's 2010 Hhr. A very thorough,and informative video.
@briansmobile13 жыл бұрын
Glad it was helpful! You're welcome!
@randallhoward30773 жыл бұрын
Love thelonger video way more helpful thanks
@davidostring8035 жыл бұрын
I watched to the end & now I know what not to work on. Thank you for a great video.
@chrismcpherson61492 ай бұрын
Hey Brian, your video of the eco reach water pump replacement was spot on! I have a 40 year old Cornwall 10 mm deep well socket that has a magnet in it. The number is 10mm-mms-0210. Hopefully you can still get this from cornwell. Thanks again for the awesome video
@chrismcpherson61492 ай бұрын
Eco tech. Not eco reach
@jacobstevens293 Жыл бұрын
Thanks for the video brother! Highly appreciated!! Prepping to do this on a 08 Saturn sky, wish me luck! Also, watched both videos till the end 🤙🏽
@ahill007ny4 жыл бұрын
Thanks Brian I purchased the Control Freak version of this tool that you posted in the description and got it done 👌
@eddiebernal23796 ай бұрын
Thank you for the video, it was alot of help. My sister has a 2015 GMC Terrian and wants me to change the water pump, but I am going to think about it.
@terryharvey4811 Жыл бұрын
I watched to the end but it took me 4 years to find it to watch.
@gerattamayo34184 жыл бұрын
Thank you so much for this video man. I been trying to figure this dumb water pump for over a month but you just gave me the information I needed to get the job done. Thee so called mechanics I talked to could not figure out how the hell to replace this pump. Even two Bridgestone Firestone places I went to turned me away because they didn’t know how to replace this part.
@djsnaps123 жыл бұрын
Watched till the end and thank you for your work.
@josephwall9161 Жыл бұрын
When I was an apprentice many moons ago my Mentor taught me to use thick grease to hold bolts inside the socket for tight areas. Dip the head of the bolt into red grease cover it good then pop it into your socket. It won’t come out until it’s threaded into where it is supposed to go.
@andyschmidt20093 жыл бұрын
Thank you so much for this video!! I did one on a customers Terrain and it is whining and couldn’t figure it out to save my life. Will be resetting the tensioner
@jonathanheap26132 жыл бұрын
I watched til the end sir thank you
@anthonyproulx3136 ай бұрын
I watched till the end was wondering what year your equinox is my daughter's is a 2016 you made this look alot easier than other video they were pulling exhaust manifold off and catalac converters off and alot of other parts
@zachmckee93892 жыл бұрын
If your new pump has sprocket on it is it ok to take it off to use this method?
@Bunkysworkshop5 жыл бұрын
Watched to the end my friend. Thanks for the video.
@briansmobile15 жыл бұрын
Thanks Craig!
@macro8205 жыл бұрын
I need this on my 2.2 in the HHR. That engine bay looks way more open than what I'm dealing with
@meganhendrickson15963 жыл бұрын
Right I did on a Saturn Vue but still great guidelines to get job done
@bernardsanchez28952 жыл бұрын
Great videos! Saves me a ton if time and money. Unfortunately mine is whining now...do you have a video showing how to fix it? Or can you direct me to some instructions please??
@briansmobile12 жыл бұрын
This is what I've got and a part 1
@richardobenshine3014 жыл бұрын
Thanks u help me out alot today. Only watched ur first video and was over book time by 3min for first time
@Luis-sanchez3 жыл бұрын
thanks for you time doing this video very helpful on my line of work best of luck
@mikeh35592 жыл бұрын
i watched both parts all the way. multitasking. and i edit videos so i feel your pain,
@NIS_ONE4 жыл бұрын
Excellent video. Watched to the end. Thanks for the great video. One of the best videos covering these excellently designed gm vehicles 😂
@endorider728 Жыл бұрын
Hi Brian, Great video and i have a couple questions. First, does the exhaust have to come down in order to access the water pump? And, is there an advantage to using the "control freak" version of the timing chain holding tool? Thanks Scott
@wallautomotive86024 жыл бұрын
Great video, good balance of time vs. information
@ironbow1235 жыл бұрын
Right to the end and awesome video by the way!
@briansmobile15 жыл бұрын
Thanks Ironbow- nice truck!
@craigbryant26823 жыл бұрын
I think I think it was a great video watched it all the way through learned a lot thanks for the video
@geojohnson56133 жыл бұрын
Good job...what hassle just to change a water pump. I hope mine doesn't go out on my 2011 Equinox! I did watch both parts to the end. There was a time when I would have tackled this job. But now I am 74 and would rather pay someone else to do it. I can tell that you have done these before. 😉
@j.carlosandrioli76395 жыл бұрын
"if you stick your finger in the back, right there" --- always the best quotes
@melsmobileservices42235 жыл бұрын
I watched to the end, brother! Great videos as always! BFATE is always why. You make great content & thanks for doing it.
@fpigunk5 жыл бұрын
I watch till the end. Thanks for making videos for us to learn stuff
@JerusBarnett5 жыл бұрын
Loved the red green reference. Keep up the fantastic videos.
@glenharper31365 жыл бұрын
Always watch to the end. Why wouldn't we.
@briansmobile15 жыл бұрын
Thanks Glen!
@davidgarcia22735 жыл бұрын
Your good bro keep up the good work. All your tips were great. I was having trouble before watching your video. Thank god i did. Thanks bro. Congrats on the pullapart win as well
@dwaynechaulk73875 жыл бұрын
Keep up the good work, longer the better!
@XChaoticComposerX3 жыл бұрын
THANK YOU for all those tips...
@NorthCoastT8 ай бұрын
I watched all the way to the end of both videos. Not sure I want to tackle this job. I have the belief that I can do it, just not sure I have the time to dedicate to it.
@chrisharley19294 жыл бұрын
great vid! starting the job tomorrow
@Ghostacc956 Жыл бұрын
I was able to get the water pump holding tool on the timing sprocket without having to remove any of the timing sprocket bolts. I am really confused as to why you pulled them off, or even why you “turned the engine” to line up the holes to get the tool on. I was able to get it on without turning the engine at all. I understand there is a thin cover that goes over the timing sprocket that has 4 bolts, but it looks like you are taking off the bolts holding the sprocket in place
@samifoaz36402 жыл бұрын
יפה כל הכבוד לך עזרת לי כמה זמן עבודה פירוק והרכבה
@chadoliver29663 жыл бұрын
Brian I watched both videos as my water pump is leaking from the side of the engine. I already replaced my thermostat and put in a new radiator. Now the water looks like it needs to be replaced plus my belt needs to be replaced and probably do my tensioner assembly as well. How long does it take to replace the water pump? I will be getting the special tool as well.
@K1NGPUFF9 ай бұрын
1-3 hours, normally 2-4 hour job but expect 6+
@crash0it4 жыл бұрын
I did this work spot on and have a wine from the pump now. Any times on what to do next?
@wadepeterson10473 жыл бұрын
The job went really good thank you for your thoroughness. I made a slick socket for bolt removal in the gear timing chain area. I just cut off a magnet and put it inside a 1/4” drive deep socket, also wrapped a little hockey tape around it for grip to spin bolt. IMG_0453.heic
@konstantinusstoyanov97495 жыл бұрын
You are passionate person, love to watch your chanel
@badge_man2 жыл бұрын
Great video, whish you had the toque specs, but everything else spot on
@kelvinwoodsworship3 жыл бұрын
Great video. I watched part 1 as well. Great job!!!
@rkdyo2 жыл бұрын
Thanks for the tutorial, it helped a lot. Thanks.
@AntonioClaudioMichael5 жыл бұрын
Great video Brian
@briansmobile15 жыл бұрын
Morning Antonio! Thank you!
@AntonioClaudioMichael5 жыл бұрын
@@briansmobile1 morning Brian How are you Brother
@jimjohnson90795 жыл бұрын
Great video brian. I was wondering if you had used the OTC 6616 holding tool. The bolts couldn't fall into the engine when they were removed.
@bernardsmith23512 жыл бұрын
You've done a great job on the water pump. But for the best results on O-rings I find that MOLYKOTE O-ring grease works best on any O-rings 😎
@d.j.99613 жыл бұрын
I have one for ya! On my 07 Pontiac G5 vin-F 2.2, The cooling fan does not operate! The fan spins when power & ground is applied. I thought maybe the relay was bad & replaced them but, That did not fix it! The temp displays on the dash so, I assume the temp sensor is okay? Since it was not operating, I removed the relay & taped into one pin & when I ground that pin, the fan comes on so, I ran a wire into the cab, to a toggle then to ground! I have a aftermarket fan controller but, the temp sensor is 3/8ths if I remember right...Any idea what size threads are on the factory temp sensor? I am wondering how I can run a aftermarket fan controller & still retain my temp display on the dash? Any suggestions???? Watched to the end!!! I enjoy watching & learning about the job that I am about to do! I watch them from beginning to end & watch as many video's as I can find regarding the issue of which I am about to tackle, To see what I am getting into! Looking for tips & tricks, & what to watch out for!!
@malohispop734 жыл бұрын
Great content sir. Keep doing what you're doing I really appreciate the approach you use.
@luisalvarez23313 жыл бұрын
great video now on the next video can you show how to use the tool to hold the 2 camshafts ?
@briansmobile13 жыл бұрын
I'll do better than that! I'll go back in time and create a part 1 of 2. You're welcome!
@badukp17925 жыл бұрын
I watched to the end. Good video.
@noecampos1359 Жыл бұрын
Hi you can use a longer 10 to aling. Tre holes
@haileysmith5224 жыл бұрын
Watched all the way, this was very informative, And a Great big help, Not sure if I'll do myself yet or take to mechanic. My pump is not leaking, but changed tstat and still trying to get hot. Could it still be the pump?? Thanks
@bierbrauer115 жыл бұрын
I always watch to the end, bro -- always solid vids!