SKIP TO 3:45 IF YOU JUST WANT THE SOLUTION, NO BACKSTORY. Plugged gas ports in the nut which holds the carburetor's float cup. If you'd like to cut to the chase, so to speak, skip to 3:45 in the video. Hope this helps someone.
Пікірлер: 162
@DuffusMonkey7 жыл бұрын
Thanks to this video I fixed my neighbors powerwasher. He was so happy he gave me a riding mover that just needs the mowing deck repaired!
@Mrsplashdown6 жыл бұрын
Good sir, you just saved me from having to buy a new carb. I had torn it down, cleaned everything, new the float worked and the needle was traveling correctly and still wouldn't start. Your tip about the bowl boat was the exact same problem I had. After several long soaks in carb cleaner and a couple good hits with compressed air, viola! She works! Thank you very much for taking the time to save other cost and headache.
@rayallen8906 жыл бұрын
I had cleaned my carburator and couldn't get my engine to run right. Changed the plug, no improvement. I always use Seafoam with my gas and use gasoline with no ethanol in it. I ran the engine rich to get anything out of it and it was still hard to start. When I saw and listened to your explanation about the main jet and the plugged ports I removed my bowl, took the main jet off, blew carburator cleaner through it, put it back on and the engine starts first pull now. Yay! Bravo!!!
@davechew51008 жыл бұрын
Wow, thanks to you I got my lawnmower fixed on my own. I spent a day cleaned and checked everything but the lawnmower did not start. No fuel was getting to the engine. I decided to give up and take it to the lawnmower repair shop. I saw your video, cleaned the screw and bingo started immediately! Thanks again!
@jaytee51922 ай бұрын
Fantastic! my Quantum was dying immediately. Cleaned the dirt inside the bolt and now, all fixed. Receiving a new carburetor by the Post in a few days (but won t need it !! thanks to your explanations ). Thanks a lot
@alzaidi77396 жыл бұрын
Thanks for the video. REAL QUICK! Remove the brass nut on the bottom of the carb bowl, and clean out the top orifice and two side orifices with a pin, needle , small wire or tiny undersized drill bit. Blow out with carb cleaner and re-assemble. Add carb cleaner / storage additive to keep it clean in winter. No Need to Remove the carburetor.
@callmehank883 жыл бұрын
Thanks geezer. 2021 and I just fixed a mates mower that was doing exactly as yours was. It wasn't totally blocked but close enough. Cleaned her out and she purring like a kitten.
@nawtmail10 жыл бұрын
Thanks a lot. Your video allowed me to do what the professional repair shop couldn't or wouldn't do. If anyone is ever in Manning SC do not go to Palmetto Outdoor Power Equipment. They claimed they couldn't get my mower to start and run. I took the carb off with the help of this video, cleaned it and it's working great. Thanks again!!!
@kelvinpeters21259 жыл бұрын
Spot on! You helped me fix my 2005 B&S 6.5 hp 3500W generator. Cleaned carb all around. Only a couple of mouse clicks from ordering a new one (not skilled enough for rebuild kits). Cleaned the nut with ports with very small wire and carb cleaner and compressed air. Reinstalled and started on first pull !!! Great Job !!
@NerdyGuy575710 жыл бұрын
Thanks for your video. I just removed the bolt and bowl, cleaned the holes in the bolt, cleaned the bowl, and reassembled. Wow! My main mower died today after 26 years so I had to get out my spare but previously perfect mower. But I had let the gas settle and dry. You really made my day! Thanks!
@Reps.and.Doubletime4 жыл бұрын
I was gonna buy a new carburetor. Found this video, cleaned the bolt, and it stays running. Thank you. 🍻
@amante47486 жыл бұрын
thats exactly what it was, an easy fix. somebody left a brand new craftsman on the curb for free as they couldnt start it after the winter sitting with the ethanol gas in it and got mad obviously. I simply undid the carb float bolt/nut as shown, cleaned the clogged orifices, wiped off the gunk, drained and refilled with pure gas and starts with one pull runnin strong. I knew this from the past but liked the refresher video here.
@dekletv8 жыл бұрын
Thank goodness for this video. I fought the exact same lawn mower for an entire day trying just about everything. I boiled the carburetor float bowl nut in water and vinegar. Started up immediately. Success.
@braderrick6 жыл бұрын
Your video has saved the day! I’ve had the carburetor off my pressure washer 3 times since yesterday troubleshooting . This one wouldn’t start at all. Thought I had cleaned every part of the carb until I watched this lol. I simply removed the bolt and could see it immediately. A quick cleaning and reinstalling it worked like a charm. Thanks again!
@gooburrum2 жыл бұрын
That bottom nut holding on the float bowl…… that was the culprit. Thanks for the video which fixed my mower.
@davidlaksa6 жыл бұрын
My bolt under the float had no holes but your video inspired to take a look at the float and it was installed upside down, I reversed it and I am good to go... Never been so excited to mow lawns since I was a kid.
@3pw44605 жыл бұрын
YOU ABSOLUTELY ROCK! I had completely torn apart and cleaned the carburetor... and was pulling out my hair (what little I have left) with frustration... Completely missed this... Thank you, your video saved me a trip to the ER!
@tsmith84947 жыл бұрын
I've been watching KZbin videos for two days trying to fix this issue on my mower and you're the first person to suggest a clogged fuel bowl nut. Everyone else seemed to have me tearing apart the entire carb looking for clogged ports everywhere else. Thank you sir! Fixed my problem in two minutes without having to tear my carb apart again.
@wayneworkman21842 жыл бұрын
Q H775EXq2a
@cmkuhl19 жыл бұрын
I was actually trying to find the part number of the carburetor when I stumbled upon your video. Mower is fixed now with no need for new parts thanks to you!
@77LionTree8 жыл бұрын
If there is a heaven you are in for sure for sharing this unclogging the holes in the brass bolt secret. I I did everything but that. A pure savior of mankind's time and mind. Thank you so much!
@daydozer7 жыл бұрын
Oh man, I was about to replace the carb on my generator until I tried this. I didn't see any clogs, but sure enough a couple of sprays with carb cleaner through the holes and it runs now! I had taken the bowl off with that screw about 50 times today looking for clogs and sediment. +suleskes you saved my day man!
@1OlBull7 жыл бұрын
Sure enough, the orifice in the bowl nut was clogged preventing fuel from getting to the carb on my Briggs and Stratton engine for my log splitter. Works great now, thanks for the video instruction.....
@themadone418 жыл бұрын
You are a life saver! Worked on many small carbs in the past but never knew this! Thanks so much!
@Dragonslayer4w48 жыл бұрын
this was actually the problem with my snow blower..after cleaning the carb numerous times with no luck, I seen this video and went out and cleaned the nut hole that goes down, it was clogged .. I said no way is it that easy.put it back together, and whalaaa!!fired up first pull and runs great!! thank god for youtube videos..
@garypopp58997 жыл бұрын
Dragonslayer4w4 very informative
@huepowered7 жыл бұрын
Same thing on my dad's snowblower. Luckily we found this video and I was able to walk him through cleaning out the screw!
@ppger448 жыл бұрын
I found that my mower has 2 side holes also on the fuel bowl bolt. One of the holes was plugged. Great video! I'm glad I watched it.
@jeepcjvii6 жыл бұрын
Thank you! This fixed my problem and saved me from buying a new carb.
@michaelwalters26068 жыл бұрын
Hi, thanks for your helpful video...I was able to start up and cut my lawn with a Lawnmower-Toro 6.0 HP Model 20010 after it sat in storage for 10 years...it started after 2 pulls...thanks again for video!!!
@mehill008 жыл бұрын
I cleaned every part of the carbeurator EXCEPT that nut, which I thought was just a nut...didn't notice the little holes in it! Thanks.
@larry007810410 жыл бұрын
Thanks. It was the float bowl nut. Tried for 3 days pulling the carburetor apart and cleaning it before I found your article. Thanks again.
@azizkian1769 жыл бұрын
Thank you for sharing. For fixing erratic speed, and those who don't care about how the carburetor works, all they need to do is just watch the last part of the video and unscrew the brass nut holding the cup to the carburetor to clean the two holes. Thats the first thing to do before tearing up the carb. Thanks.
@Fitz357AS7 жыл бұрын
Aziz Kian , thank you!
@dannilaser166 жыл бұрын
I hear that.
@Joelaurencechannel8 жыл бұрын
Well that was it, THANK YOU I can't afford another lawnmower so I took it on and low and behold the carb. cleaning didn't work. well back to youtube. another idea, didn't work then YOU. I had no idea that bowl nut or whatever it is had dual purpose. The bottom hole must have been plugged not the side ones. Now it's running again. Thank again good job
@joshpiceno46049 жыл бұрын
Awesom! Just fixed my power washer that would not start. Thank you sir! The bolt at the bottom of carburetor was clogged and I had cleaned the carburetor the day before but missed the bolt and now it runs like a champ.
@Tom-ym5bo7 жыл бұрын
Ditto
@OreExplorer8 жыл бұрын
I cleaned every part of the mower and thought this was just a nut....many thanks!
@paulfenn9402 жыл бұрын
So I had exactly the same problem and like you but not quite to the same extent, I took things apart but still no luck. Watched your video, went back and pulled that brass plug and sure enough, plugged. Ran a needle through the hole, reinstalled and boom, off she went! Thanks so much for the great video and solution! On we go…
@jacklucas72657 жыл бұрын
Thank you for your post. In my never to be humble opinion you have earned your place in heaven as far as I am concerned!
@tim423588 жыл бұрын
I just pulled off the air cleaner and took off the float bowl nut and cleaned it. I am running like new! Thanks!
@theaquariumcurmudgeon10 жыл бұрын
Hey thanks so much, your advice allowed me to get my pressure washer running without having to take it to my father-in-law for repairs!
@DS-rs1xv10 жыл бұрын
Thanks for the video. My pressure washer has been sitting for years and the varnish had clogged the holes in that screw. It takes a very fine wire to get that top one cleaned out. Once it was clean (and I'd changed the oil and added fresh gas), the engine ran great.
@david35803 жыл бұрын
Fantastic video. Saved me a shed load of time and effort. Thanks!
@kevinnulton93928 жыл бұрын
Thank you so much! This was exactly my problem! I wish I would have watched this before I replaced the thermostat & carburetor. It's a pain in the butt to replace that thermostat.
@mclarkallen7 жыл бұрын
how could 138 people thumb down this video....it was great. Thanks.
@johnpauljohnson65258 жыл бұрын
Poulan Pro Briggs & Stratton 675EX Series, this was my exact problem, thank you for your video and helpful information.
@olifield9 жыл бұрын
Great video. My rotorvator ran for about 30 seconds then as soon as I engaged the drive it stalled. Also I was having to run with choke on prior to this. Followed your instructions and found green layer, like lacquer, in the float bowl. Cleaned it all off with white spirit, steel wool, used a pin to clean holes and works perfectly now. Saved me so much hassle as I was able to finish the job that day. I have been told the green substance was cleaner the fuel station puts in, nice.
@luisbermudez89559 жыл бұрын
Great video!! I had that exact same problem!! I've been trying to get it started for two days after it sitting for a few months. took the carburetor apart twice and cleaned it twice but never thought to look at that nut until this video. Thanks a lot!!
@jameshintexas8 жыл бұрын
Just fixed my pressure washer, thanks to you Suleskes.
@moneyjones23236 жыл бұрын
This Video Just opened my Mobile Detailing Business! Thanks !
@kevanbarnes1137 жыл бұрын
Don't often post, but I must take the time to Thank You. I cleaned EVERYTHING (except that jet bolt). :/ Thank you for your time.
@gjk2914 жыл бұрын
What a great video. I was looking to change the carb as I had cleaned and checked it several times, didn't check that nut though. I will be trying this out first thing tomorrow!
@creativeguitarstudio9 жыл бұрын
Just fixed my lawnmower using your video! Thanks a MILLION.
@abijahgribble Жыл бұрын
Worked for me as well!! Thank you for this video, didn't even have to take the carburetor down because od this video 🤙, thank you sir!!!
@andyandmarlys9 жыл бұрын
Nice work. Solved my problem. Starts first pull once again... it was the holes that were 90% clogged. Just ordered new float bowl and gaskets as the old gasket had worn out and probably is part of what gunked up the holes.
@dannilaser166 жыл бұрын
You just saved me a ton of time. You’re my hero. THE CHECK IS IN THE MAIL.
@tonyjandura96546 жыл бұрын
carburetor float vessel, float reservoir, it's actually called the float bowl
@OilBaron1006 жыл бұрын
Outstanding! Thanks for posting. I have starting issues too; I will try this out.
@SickaydaMars8 жыл бұрын
Hell Ya it worked, I think in general, just stripping the carb down to it's basic parts and clean the crap out of every little part, My problem was it would start, run for about 3 seconds and then die, now it runs great! props, lesson learned!!
@KeoweeChristopher17 жыл бұрын
The key is the tiny hole that runs through the body of the nut on the float cup. Soak the bolt in carb cleaner, then run a fine wire through the tiny hole until you can see it through the larger two holes which intersect the small channel. Use the wire from a twist tie, after stripping off the plastic or paper. Worked like a charm for me.
@neptuneruler289 жыл бұрын
Thanks a lot for your video actually I knew how to clean the carburetor but where you opened my eyes to was that switch next to the muffler I took that off a couple of days ago but didn't put it back correctly, so even after I cleaned the carburetor I found myself making the carburetor rev up by holding it. But when you said that switch next to the muffler controlled the carburetor the bell went off, running great.
@jonasfellgard71958 жыл бұрын
thanks. made my mower work like a charm.
@Aesir511 ай бұрын
Love that you pull the mower onto the wife's best rug 😂
@gatorfan85378 жыл бұрын
thank you for the video it fixed the problem I had on my mower that I had had apart several times thanks again
@seemore788 жыл бұрын
Awsome cleaning that nut worked for me
@mikemahoney29376 жыл бұрын
Thank you! This was exactly what I was looking for and it worked perfectly.
@jamesdenney96536 жыл бұрын
I have one of the Murray 30" mini riders with a similar carb. I had intermittent fuel issues with it from the second week I had it. Turned out to be that bowl nut. I'd sprayed them through with carb cleaner and assumed they were clear... not so much. I probed the holes with a drill bit of a slightly smaller diameter and pulled out a small brass chip left over from the machining process. =/
@huepowered7 жыл бұрын
Great Video! Helped me out immensely
@tvmanjon8 жыл бұрын
Best You Tube Video. This was a easy job and didn't cost me a thing but a little time Don't buy a new carb when its so easy to clean it Thanks Suleskes
@smytree9 жыл бұрын
You sir get a gold star. Thanks for saving me so much time I was going to put the carb but alas just had to clean that bolt/jet assembly.
@Kothas012 жыл бұрын
Same carb body as a snow blower however the choke is set up different. The Toro snow blower doesn't have an air filter by design. All the air ports can get gunked up easily.
@TallLongGuy7 жыл бұрын
@4:20. ... yup, that was my problem! Thanks
@fred295269 жыл бұрын
Great Video , My pressure washer wouldn't start this year and that was the problem You saved me time and money ThankYou!!!!!!!!!!!!!!!!!!!!!!
@Tylerthomasmiller847 жыл бұрын
Sir, I cant tell you thank you enough!!! This totally worked for me!! Exactly what i needed! And thank you for the explanation of what everything does at the beginning!!!!
@themattk26 жыл бұрын
just saved me a whole bunch of time, thank you!
@deepcover6809 жыл бұрын
Just found out if fuel is left in your tank over a month it begins to break down and will not start. The ethanol sets at the bottom of the tank and will cause no starts. The tank had to be completely drained and fresh fuel added to the tank. It started right up after replacing the month old fuel.
@grassroot0118 жыл бұрын
And this being partially plugged will cause surging. That is running fast then slow and repeated over and over. I hear a lot of these going on the the neighborhood.
@jonienglish32316 жыл бұрын
my 250 cc 1150 snow engine main jet plugged , cleaned and also cleaned the needle and the main jet shaft small holes now surging !!!!!!!!!!!!
@thevoiceoftruth557 жыл бұрын
This fixed my mower!!! TY!
@ericstuckey76207 жыл бұрын
thanks this helps a lot my 5 year old power washer is working.
@johnelliveps80022 жыл бұрын
I had the same problem about 4 to 5 years ago with a blocked jet in the carby and now I now always use a very fine mesh when pouring petrol into the tank.I could not believe the crap one get from buying petrol at the station.I found sand ,dirt and ever pubic hair in the damn thing.
@aveoxus11395 жыл бұрын
Had mine apart (used to run the hydraulic pump on my husky log splitter) and I had already shined up the coil and used air to clean out the jet in the carb, guess I should try cleaning the nut intake
@walterkersting99228 жыл бұрын
Um, I ran over a beer bottle with my lawn mower that my neighbor threw in my yard and he's saying I did it on purpose just to shoot glass and rocks and dust at him and his beer buddies, so does that hurt the mower? I care about it cause it has a Briggs and scrap iron.
@bcb66348 жыл бұрын
thanks! This was my issue as well.
@alexthestork7328 жыл бұрын
Thank You , this worked to perfection !!!
@johntrauger687 жыл бұрын
I had that same problem last season. I only found it out of desperation and close inspection.
@clemensschmitter76165 жыл бұрын
Clem schmitter Thank you. Great Video and a Fixer!!!!
@leecno7 жыл бұрын
Thank you so much! Made it easy!
@LaughingRandomly8 жыл бұрын
thanks for the helpful video!
@arfurdaley63992 жыл бұрын
Very useful to know !! Thanks
@tigerstripes39262 жыл бұрын
Man this is awesome great vid. Thankyou
@zircon30358 жыл бұрын
Thanks, worked a treat!
@696johnboy10 жыл бұрын
thank you your video helped me and gave me all the information I needed to fix my carburetor on my generator ;-))
@Jim-ie6uf6 жыл бұрын
Glad you’re learning.
@rogerlovett63038 жыл бұрын
The root cause of this problem is ethylene dibromide (EDB) which is an additive to the refined petroleum fuel. It degrades over a period of months and produces the gunk sediment that settles in the float bowl and glues up carb jet ports and those small holes in the brass pieces. This affects everyones engines, even us in England !
@Evoy68 Жыл бұрын
Thanks for this video this helped alot!!
@Daluke619 жыл бұрын
I've got a similar B&S engine; one with an auto choke, too. Mine is the 6.75 hp model with a primer button. In my case, engine always starts up just fine, first pull most of the time. Trouble is, when it's hot, restarting is a major pain in the ass. Floods out most of the time after the first pull (when it's hot) and it'll take well over 20-30 pulls to finally get it restarted. Once it's running again, operates just fine; the problem only occurring after shutdown. You're pointing out the auto-choke and it's heat/thermal characteristics got me thinking my problem may have something to do with it, not necessarily a carb or fuel supply issue. Regardless, good information... thanks!
@brianperkins61217 жыл бұрын
when warm starting the thermal actuator near the muffler is supposed to hold the auto-choke mechanism fully open to prevent choking a warm engine ,, there is a more detailed visual description of how Briggs and Stratton auto choke mechanism works they can be quite temperamental also check simple common things like dirty Air filter and fuel cap vent ,, A carburetor float that not closing will also tend to flood a warm engine
@goedeck18 жыл бұрын
If you blow it out with compressed air check that the tiny red rubber seal is seated under the needle valve.
@machapee44279 жыл бұрын
Thank you. Great video and a fixer!!
@Johnofsulphur7 жыл бұрын
This guy is a WONDER! I had a Briggs Generator that has given me troubles .... Start and then quit! ( sound familiar? ) The bottom "bolt" was completely PLUGGED... as were most jets...One more issue..Before the starting issue, the generator would quit by itself after some time. . The plastic gas tank vent was completely PLUGGED also.... You should see how much FUNK came flying out after carb Cleaner, wire reaming and 90 PSI!
@Johnofsulphur7 жыл бұрын
It started with the first pull! and ran perfect.
@Johnofsulphur7 жыл бұрын
Briggs model 030238 Generator...121012 0114 E1 Motor....591299 Carb
@jimgarrison73867 жыл бұрын
I had exactly the same problem. but I didn't figure the holes were plugged. it was very clean except for some dirt or tiny sand in the bottom of the float bowl. I'll have to take the jet back off n run a wire thru it. I just hope I didn't lose the needle. (the carb is still on the motor). thanks for your help
@jamierace8443 ай бұрын
Thanks for the video. Do you have a video of putting it back together? I was given a lawnmower that doesn't run. Come to find out many things aren't connected. One of them being the automatic choke. What' gets connected there? I can't find anything.
@asjackman8 жыл бұрын
Thank you, this worked!
@MegaFlaxman7 жыл бұрын
Nice fix!! And is there any way to adjust the engine speed, seems yours runs much faster than mine, I'd like to kick mine up a notch