Broken Cam Position Sensor Removal, Bad Day!

  Рет қаралды 7,257

74stevedc

74stevedc

Күн бұрын

Пікірлер: 28
@lightpawshird
@lightpawshird 8 ай бұрын
I had one break off inside the block today too. I used a 1/2 sheet metal bolt with a 9/16" head and used it to screw into the plastic and through the back of it (pushing down against the side of the hole with the wratchet to drill into the broken plastic housing.. used the screw driver method originally explained here to pull it out.. easy and simple.
@74stevedc
@74stevedc 8 ай бұрын
Yes, Remember it wasn't fun glad you were able to get it out.
@lightpawshird
@lightpawshird 8 ай бұрын
@@74stevedc Than you for making this video!
@74stevedc
@74stevedc 8 ай бұрын
@@lightpawshird Thanks for watching.
@74stevedc
@74stevedc 3 жыл бұрын
This particular one is a 2007 F150 probably all your 5.4 trinton engines 1997-2010? Will work on probably any make or model.
@anarchybuildz1749
@anarchybuildz1749 11 ай бұрын
This just happened to me the same way you explained it but, I tried to take it out with a screwdriver and I think I ended up sending that plastic right inside and now my whole finger fits in, what do you recommend doing ?
@74stevedc
@74stevedc 11 ай бұрын
I like the drill bit, it wasn't fun that's for sure, let me know how it turns out.
@TrevorGottschall
@TrevorGottschall 4 ай бұрын
This same thing happened to what did you do?
@74stevedc
@74stevedc 4 ай бұрын
Did you watch my video, I used a sharp drill bit,
@undrejohnson2588
@undrejohnson2588 Жыл бұрын
I'm trying to replace mines now...I can't seem to get it out!😢
@74stevedc
@74stevedc Жыл бұрын
There definitely not fun Undre, The drill bit worked well for me.
@undrejohnson2588
@undrejohnson2588 Жыл бұрын
@74stevedc....is that the only way to pull it out? I've been trying to get it out for over an hour now...I sprayed some wd40 on it
@74stevedc
@74stevedc Жыл бұрын
@@undrejohnson2588 I only did it that one time. I remember when it breaks off there's really not much to work with.
@timbuk2.019
@timbuk2.019 Жыл бұрын
I pushed mine back into the block I gues it will chew it up but I should've warmed up my engine before
@74stevedc
@74stevedc Жыл бұрын
I feel your pain, definitely not a fun project.
@74stevedc
@74stevedc 3 жыл бұрын
This truck has 290,000 miles and climbing daily.
@PedroMendez-i7j
@PedroMendez-i7j 4 ай бұрын
I tried to remove mine but it fell in... It's that bad?
@74stevedc
@74stevedc 4 ай бұрын
It was my first time doing it, I'd try a drill bit or a easy out Pedro, hopefully it works for you. I was worried that would happen, but you have to get it out or timing will be way off and possibly not run.
@tdeleonxx
@tdeleonxx Жыл бұрын
What should I use if the broken camshaft is plastic that's stuck inside ?
@74stevedc
@74stevedc Жыл бұрын
I used a new drill bit found the tightest fitting one and tapped it in. Mine broke off so I couldn't use pliers. A easy out might be another option and a pb blaster soaking overnight if you have a option to. Thanks for watching my videos I really appreciate it.
@linmatthew6197
@linmatthew6197 9 ай бұрын
thanx you relly helps me alot 🎉
@74stevedc
@74stevedc 9 ай бұрын
Hi Mathew, Glad to hear it went well it's never a good thing seeing something break off like that.
@74stevedc
@74stevedc 3 жыл бұрын
Start off with the smallest bit first, that way you can work your way up. Tap drill bit in try to rotate bit tapping it in with hammer they rust in. Side note bought cheap harbor freight kit and this bit was razor sharp never used, dull worn out bit might not work for you,🍻
@lightpawshird
@lightpawshird 8 ай бұрын
Use the bolt method above. No chance of damaging the threads in the block. Using a drill bit your going to get shavings down inside your engine that is going to cause future problems and high repair bills. Using a sharp tipped 1/2" sheet metal bolt with a 9/16" head you will thread through the plastic and then can use the flat head screw driver to pop out the plastic like a cork'
08-14 Sierra/Silverado (GMT900) Cam Position Sensor Re&Re
5:38
DIY - Signs & Symptoms of a Bad Camshaft Position Sensor (CMP)
7:11
Как Ходили родители в ШКОЛУ!
0:49
Family Box
Рет қаралды 2,3 МЛН
Какой я клей? | CLEX #shorts
0:59
CLEX
Рет қаралды 1,9 МЛН
24 Часа в БОУЛИНГЕ !
27:03
A4
Рет қаралды 7 МЛН
The Lost World: Living Room Edition
0:46
Daniel LaBelle
Рет қаралды 27 МЛН
How to Remove Broken Camshaft Position Sensor 07-13 Chevy Silverado
9:34
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 132 М.
SYMPTOMS OF A BAD CAMSHAFT POSITION SENSOR
3:04
EasyAutoFix
Рет қаралды 1 МЛН
Remove broken cam position sensor from engine block
4:13
Kevin Harper (List With Kevin)
Рет қаралды 64 М.
ford 05 F150 5. 4 crankshaft position sensor
7:51
Marty09933
Рет қаралды 44 М.
Crankshaft Position Sensor Test
4:21
ScrewsNutsAndBolts
Рет қаралды 530 М.
unscrew the broken bolt without drilling and welding, simple trick
8:05
Quickly Diagnose The Most Common Fault on Ford 4.6L & 5.4L 3v Engines
7:30
FordTechMakuloco
Рет қаралды 1,3 МЛН
Как Ходили родители в ШКОЛУ!
0:49
Family Box
Рет қаралды 2,3 МЛН